Each year, the coffee machines at Ericsson in Kista produce around 100 tons of ground coffee waste.The companies Coor Service Management, Löfbergs Lila and Selecta are all responsible for differentstages in the logistical chain in delivering coffee and, together with Ericsson, they want to increasetheir environmental benefit. The plan is to produce biogas through anaerobic digestion instead ofincinerating the coffee waste in a heating plant. The results are to be presented as different businesscases in which different biogas plants are compared with the reference case (heating plant),comparing costs and environmental impacts.There are two major environmental benefits from producing biogas; reduced carbon dioxideemissions from when fossile fule is replaced by carbon neutral biogas, and reduced emissions fromreturning digestate from the bio reactor to farmland instead of using industrial fertelizer.In order to determine the biogas potential in coffee waste, a couple of properties had to bedetermined in a laboratory. Properties such as the dry substance content, heating value, moisturecontent and ash content. The results show that 100 tons coffee waste could produce around 16 500Nm3 biogas which would contain 163 MWh.The biogas reactor and upgrade plant both need energy gas to function and uses around 14 MWh ofthe produced gas.

Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

At the Division of Electricity at Uppsala University there is an experimental rig forhydroelectric generators. The experimental rig?s vital part is a 12-pole synchronousmachine, whose electrical characterizing parameters (resistances, inductances andtime constants) are unknown. The aim of this thesis is to characterize the machine inits current state by perform a Standstill Frequency Response (SSFR) test. From theanalysis of the measurement data, which is a part of the test, a set of basic parametershave been received.

Perfluorinated substances (PF) are environmental pollutants that are used to coat fibres of so called ?all weather clothes? to make them water resistant. PF are effectively spread through water. Waste water treatment plants (WWTPs) are a pollutant source of these substances. PF are poisonous to different kinds of organisms, and supposedly also to human beings, if concentrations are sufficiently high.Perfluorinated substances have been investigated at three waste water treatment plants in Stockholm during the 2000?s.

This report is on concrete work during the winter and is implemented on Peab?s behalf. The assignment was to describe the differences between a summer- and a winter casting. While it shows the complications that exists, it also show what aids are available, both electronic via computer and physical aids.The information that I have developed is originally from theory in books, information on the internet as well as practical experience from knowledgeable people that works in construction output. Other theories are those I have learned throughout the education to become a construction engineer, including all oral sources over the years.The results I have come up with, I hope will be able to help future construction projects in the planning phase of a winter casting.

Pharmaceuticals that are found in marine ecosystems are a threatening environmental concern, which is known to harm both animal and plant life. One of the reasons for this problem is that the waste water treatment techniques are not optimized to clear waste water from its pharmaceuticals contain. In this master thesis four Swedish treatment wetlands were studied, and their ability to reduce numerous pharmaceuticals in waste water. The four treatment wetlands that were studied were those in Oxelösund, Trosa, Nynäshamn and Eskilstuna. Two ecotoxicological tests and chemical analysis were used.

Vattenfall district Heating power plant in Uppsala produces district cooling with absorption heat pumps which leads to a large amount of waste heat that has to be cooled with evaporative cooling towers. The Environmental Court has ordered Vattenfall to survey the possibilities to recover the heat, which is the focus of this thesis.The study begins with an overview of the system, and conditions and limitations for waste heat recovery is examined. In the next step alternatives to recycle the heat is evaluated, either by direct recovering or by upgrading.First, the technical possibility of each alternative is discussed, and then the operation time and the amount of recovered heat is calculated. Those alternatives which are possible are brought further to an economic analysis.The cost of investment for each alternative constitutes the basis for a present value analysis. The results are put together in a table where the total amount of recovered heat is compared with the present value for the different alternatives.

Many of todays studies show that district heating is one of the betteralternatives as heating source because of its low environmental load.The energy source is often leftovers from other processes producing energy or waste, like garbage or chips.Electricity in combination with geothermal heating is another heating system that has increased sharply during the last years, and also this system decreases the discharges that have negative affectson the environment compared to several other heating methods.This report aims to, concentrated towards these two different heating systems, estimate the amounts of discharges they indirect cause and how the environment is affected.We have calculated the mean value for discharges of carbon dioxide, nitrogen oxide, sulphur oxide and dust generated from electrical power used in Sweden.Through interviews and research we have gained data for the same substances that district heating based on combustion of garbage and biofuel generates.We have also in cooperation with a housing company chosen a building we see representative for many of the new single-family houses built in Sweden today.Based on its shape and appearance we theoretically created three alternatives of the same house, each of them with climate screens different from each other.Together with the amounts of discharged environmental affecting substances, these houses were the base for our calculations and studies when investigating the different heating sources environmental effect.The results have thereafter been analyzed and discussed from different angles..

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

Title:The issue of unplanned stoppages caused by failure in medical technology equipment ? A study within the hospital of Kalmar with a focus on manage-ment, security and quality Author:Anna Förster, Ambika Linder, Sandra Nyqvist Tutor:Thomas Karlsson Institution:Linnaeus School of Business and Economics - Linnaeus University Kalmar Date:2011-01-14 Purpose:The purpose of this study was to examine unplanned stoppages caused by medical technology equipment failure in the healthcare operation within the hospital of Kalmar. Our study is based on a number of specifically selected incidents which show the consequences these disruptions cause in management, security and quality within the operation. Our intention was also to examine what role the medical technology department of the hospital plays in the care production operation during these unplanned stoppages. Method:Through a qualitative study we have generated material from a number of interviews with staff working in the hospital of Kalmar.

In the last decades, lean production has proven to be one of the most important organizational paradigms in manufacturing. The lean concept has also spread into the service industry where it is applied within a range of different areas. The wide applicability of lean principles has spurred the authors of this study to apply the principles in the context of the operations of a Swedish remand prison. The thesis examines the process a client of the remand prison Häktet Kronoberg goes through from the time of arrest until he/she is released or convicted and transferred to jail. Based on lean tools and principles, the thesis maps and analyses this process.

In the coming years, organic food waste will be collected in the region of Gästrikland, Sweden. The collection is planned to cover the entire region by the end of year 2007. To start with, smaller amounts are being collected and transported to a central composting plant in Sala. However, a central composting plant in the region of Gästrikland is projected.The objective of this thesis is to evaluate a number of possible methods for composting of organic food wastes regarding their environmental impacts and localization.There are four scenarios for future composting of organic waste that have been evaluated. There are two that consist of membrane composting, either in Sala or in the region of Gästrikland.

Water logistics has long been a problem in order to effectively carry out stump treatment in both thinning and final felling. It is important that the stump treatment? equipment is configured as well as a sufficient amount of water is carried out on the harvester to get a cost? effective treatment. The flow control of the equipment has improved and water can be dispensed more efficient, but still the amount of water on the machine is a crucial factor in the total cost estimate. The knowledge of the tools available to bring water as well as the internal logistics of loading and transport to the felling site is deficient. Increased focus on "smart" solutions to manage water cost is of great importance in order to combat Hetrobasidion spp in both thinning and final felling. The purpose of the study is to describe and summarize different solutions of water logistics at stump treatment in final felling.

This thesis work contains a litterature study about electrical motors in general and how PWM-patterns for brushless DC-motors can be made. A suitable method has been implemented as a simulation model in VHDL. A simulation model of a brushless DC-motor which describes the phasecurrents, torque and angular velocity has also been made. The motor model made simulations easier for the complete PWM-system. The design was synthesised and tested with a prototypeboard including a SPARTAN II FPGA.

When rubber equipment in a milking system ages, physical and chemical deterioration occurs and cracks, crevices, as well as deposits of organic and inorganic material is formed on the surface. Bacterial colonization can accumulate, especially on ageing rubber equipment and if the cleaning procedure is not functioning properly. Formation of biofilm in milking equipment could in turn cause bacterial contamination of bulk tank milk. ATP bioluminescence is a fast and easy way to determine the hygienic status of a surface based on its ATP content, and results are given in relative light units (RLU). The method measures both bacterial contamination as well as residues from other organic material.