In studies of serum, in the early 1930s, from patients with pneumonia, a factor was found. It could agglutinate certain pneumococcal species. This factor, which later became known as C-reactive protein (CRP), increased sharply during the early and middle stages of the disease. CRP was identified as an acute phase protein and found especially in bacterial infections. CRP is synthesized in the liver by stimulation of interleukin 6 (IL-6), which is produced by the monocytes, and consists of five non-covalently bound subunits.The aim of this study was to compare two different analytical instruments (Vitros 5.1 FS Ortho-Clinical Diagnostics and QuikRead CRP Orion Diagnostica) for CRP analysis.

Reducing the CO2-pollution, resulting from the combustion of fossil coal for energyproduction, is important to affect environmental changes. One way to achieve a reductionis to use the oxy-fuel technology. The technology uses O2 and re-circulated flue gasduring the combustion which results in a flue gas mainly consisting of CO2. The flue gascould then be compressed and stored without environmental effects. A problem thatfollows from the compression is the risk of acidification in sensitive parts of the process.Acidification can occur because of reactions following from the contact of condensedwater and sulphur- and nitrogen-oxides which are also present in the flue gas.This report compiles and evaluates the basis of a scientific unit with the purpose ofexploring the possibilities of extracting impurities of SOx and NOx from the flue gases.The dimensions of the unit are based on basic conditions, defined for an existing oxy-fuelprocess at Chalmers, and on the results of computer modelling.

The public service within health and care has changed remarkably during the last 30 years. It has been inspired by management ideas from profit-making businesses. Those thoughts are an umbrella term called Nex public management. In what way has New public management influenced the public service in Sweden? Important concepts in the change of public service are quality, effektivity and goals.

This report is presenting an approach that can be used to measure water surfaces in difficult conditions caused by dense vegetation and lack of nearby known points. The objective was to make a contribution to necessary measures for adaptation against floods in Grums Municipality along the stream Karlbergsån, which may occur when persistent rain raises the level of the stream. Along the river there are low-lying areas prone to flooding. According to Grums Municipality, the stream may widen where the water level differences are large, to create a better flow path and to counteract flooding. Grums Municipality was also interested in survey stormwater discharges which may affect the water level in the stream.

Background Research concerning footing and its contribution to injuries has been conducted primarily in racing Thoroughbreds. Studies in UK and Japan indicate that some specific factors could be responsible for an increase in performance-associated injuries. Researchers in Sweden have performed studies on Standardbred trotters. More research is needed to be done on equestrian sports since requirements on footing are not exactly the same in riding and trotting horses. The lack of scientific evidence on the construction of equestrian surfaces has lead to anecdotal validation of designs.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

The thesis mission is to investigate whether the swiveling laser that Vectura (former Vägverket Konsult) has in use to measure the road areas and straddle measuring can be used to detect differences in the reflective road markings function. This is to increase use of the swiveling laser and get rid of the manual measurements performed today.Currently, the measurement of road markings reflective function is performed with both mobile and handheld measuring instruments. The purpose of this thesis is to develop better methods for determination of road markings? reflective function, in order to facilitate the description and suggestions for improvements of the maintenance of road markings reflective function.The questions that the thesis has been to start with are:Can the swiveling laser detect differences in longitudinal and transverse road markings reflective function?The accuracy of measurement has been sweeping the laser over the reference instrument (LTL-2000)Is it necessary with a conversion factor for swiveling laser data against the reference instrument data?To answer the question 2 and 3, there has been a field work in Värnamo where a road stretch with longitudinal road markings and zebra crossing (transverse road markings) has been investigated with a swiveling laser and LTL-2000.The formulas and calculations contained in the thesis are drawn from scientific reports that are produced by VTI in Linköping. The same formula that was used to calculate the optical measurement data was also used for the swiveling laser data.

Normally the operational amplifier is used as a component in active filter design. The goal for future components in filter design is large bandwith and the use of low supply voltages. The use of current-mode instead of voltage-mode circuits gets a step closer to the required performance. A component that use current as the signal conveying part is the current conveyor. In this report a comparative study between two current conveyor structures of second generation (CCII) is performed.

In this project I have created a design for the delivery rooms of Swedish hospitals with the psychological aspects ofbirthgiving in focus. This is something that I think the delivery rooms lack and so far it has been the midwifes job to,without any tools, give the women in labor the mental support and encouragement they need.My goal was to give the midwifes a tool to work with when it comes to encouragement, something helping themhelping the woman to feel safe and relaxed, strengthened, informed and in control of the situation.I choose to focus on the difficulties measuring the physical work the woman in labour had done and what was leftof the labour. I wanted to visualize the process of the birth, allowing the woman to see and being able to focus onwhere during the labour she is, how far she has left and also being strengthened by the amount of work already managed.Further I wanted to make the woman feel invited to take control over the birth and the room in which she isin labour. I wanted her to be able ? if she wanted ? to make her own settings of the mood in the room, deciding forherself if she wanted a more relaxed environment or perhaps a more energetic.

The purpose with this examination is to build a measureequipment to AerotechTelub AB (AT), who will registrate fault in SRAM-memory in contact with cosmic radiation. The equipment will be created around developcard from Memec Design with FPGA from Xilinx. The logic in the FPGA will be implemented with the hardwaredescribed language VHDL. The SRAM-memory that will be tested is build in CMOS-teknologi. The memorycells will be loaded with a predecided bitpattern.

        This is a report that describes the entire process of design of a measuring station for rolling resistance. The report is structured with elements of Fredy Olsson's method.The report also includes a brief presentation of HGF, the company that will manufacture the machine. Requirements and preferences are set up and used in a weighting of criteria by which product suggestions are based. These suggestions are used in the evaluation to produce a final draft product. Solutions to major functions are produced by criteria?s. Component selection for all components is performed, a CAD-based model is developed and an economic analysis is set up. FMEA analysis is set up. The report ends with a brief summary, critical review and suggestions for further work..

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

The focus of this thesis is primarily in electronic construction and describes the design process for a microcontroller circuit board from concept development to prototyping. The client develops test fixtures for automated testing of products within the electronics industry and needs a new controller circuit for the test fixtures that can handle controls and basic testing. An investigation into the needs of such a system is conducted and a prototype printed circuit board assembly is manufactured.The prototype is developed with focus on protection against electrostatic discharges and overvoltage. Among the functions that are included are voltage measurements, communication interfaces and control of input and output currents. Firmware for the prototype is developed and configured to communicate with a PC through USB interface for control and collecting of measurements..

        This is a report that describes the entire process of design of a measuring station for rolling resistance. The report is structured with elements of Fredy Olsson's method.The report also includes a brief presentation of HGF, the company that will manufacture the machine. Requirements and preferences are set up and used in a weighting of criteria by which product suggestions are based. These suggestions are used in the evaluation to produce a final draft product. Solutions to major functions are produced by criteria?s. Component selection for all components is performed, a CAD-based model is developed and an economic analysis is set up. FMEA analysis is set up. The report ends with a brief summary, critical review and suggestions for further work..

Abstract (in English)The task for the diploma work was to develop methods for measuring of moisture content by the Karl Fischer method, in jam, jelly sweets, and fudge.The start premises was a for the company whole new equipment, which should be started up. Then programs should be developed for different kind of samples.In the task it was as well included to develop methods for dissolving the different kind of samples, since the Karl Fischer method demands completely dissolved sample material..