To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

The tribo system ice-curling stone was investigated in order to understand the mechanisms behind the stones' behavior on the ice sheet. The problem with non-identical stones should also be addressed.The stone curls, that is, its sliding path deviates from a straight line to the right for a clock-wise rotation and to the left for a anti-clock-wise rotation. Several mechanisms to explain this behavior have been proposed over the years but none has been successful.By carrying out experiments at the local curling rink and studying silicon castings of ice- and stone-surfaces with scanning electron microscopy and vertical scanning interferometry, it has been decided that the curl is not due to dry friction, ice-debris or the difference in friction on the left and right side of the stone. The side force comes from the fact that the friction is higher at the back of the stone than at the front.The contact between stone and ice is never completely dry, nor in the hydrodynamic lubrication regime. It is probably a combination of hydrodynamic lubrication and a contribution from mechanical scratching of the ice.

To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

The research work performed in this thesis has been carried out at the Production Tech-nology Centre where the Thermal Spray research group of University West has its work-shop and labs.This research work has been performed in collaboration with the International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI), Hyderabad, India.First of all, I would like to express my sincere thanks and gratitude to my supervisors Dr. Nicolaie Markocsan and Dr. Nicholas Curry for their guidance, great support and valuable suggestions without which this work could not have been possible. I would also like to thanks Prof. Per Nylén for keeping faith in me and providing me an opportunity to work at PTC, which is a great place to perform research.

The main aim of this thesis is to investigate the implications and dynamics behind consistency between individual resource allocation decisions and corporate strategy concept. The telecom industry, a high-Velocity environment going through an extensive deregulation process, is put under the magnifying glass. Japanese telecom giant NTT Group is compared to its German counterpart Deutsche Telekom. Potential antecedent factors in the strategic decision-making process to consistency are studied. It is also examined whether there is a direct interplay between consistency and economic performance.

Att tidsperceptionen är påverkbar har tidigare påvisats. Studien syftar till att undersöka huruvida tidsperceptionen påverkar fartperceptionen, med hypotesen att när interna taktgivaren går snabbare uppfattas farten som lägre. 28 försöksdeltagare fick under fyra betingelser (Lugn, Stressig, Egen musik och Tyst) utföra tids- och fartestimationer under bilfärd. Inga signifikanta resultat påvisades ifråga om vare sig tidsperceptionen eller dess inverkan på fartperceptionen. Däremot skilde sig prospektiv estimation av medelfart åt beroende på betingelsen.

During the timber floating era, most of Sweden?s watercourses were altered. This decreased the amount of available spawning habitats for salmonids, and hence had a negative effect on the riverine brown trout (Salmo trutta) populations. Reconstruction of spawning grounds is today a common measure in restoration of altered streams in Sweden. However, very little evaluation of the effectiveness of these reconstructed spawning grounds exists.

AimThe main aim of the study was to investigate the difference in bilateral deficit between rowers and sprinters during maximal eccentric/concentric muscle actions.? Are there any significant differences in bilateral deficit between rowers and sprinters?? Do the amount of years in practice effect the bilateral deficit?MethodFourteen male subject participants divided in 2 equal sized groups (7 individuals in each group; rowers and sprinters) performed maximal unilateral/bilateral eccentric and concentric muscle actions in a leg press machine at a Velocity of 0.2m/s. The range of motion in the knee joint was 70° ? 140°. Dependent t-tests have been performed within each group pre and post test.

A manufacturing machine at the engineering company Sandvik Coromant has a positioning table which task is to move an item linearly. The positioning table has a linear motor capable of high Velocity and acceleration. This makes it possible to achieve short cycle times and a more profitable production.The purpose of this thesis is to bring forward a new concept which is more adapted to the requirements of the positioning table. The reason is that the current positioning table provides an unnecessarily positioning accuracy of 0.01 mm, while the requirement for the positioning accuracy is just 0.1 mm. The goal is to reduce manufacturing and component costs.To develop a suitable solution an approach for the concept development process has been performed.

The report examines the factors which may be a contributing cause to the problems that are present when ferritic stainless steel are eddy current tested in a warm condition. The work is carried out at Fagersta Stainless AB in Fagersta which manufactures stainless steel wire. In the rolling mill there is an eddy current equipment for detection of surface defects on the wire. The ferritic stainless steels cause a noise when testing and this noise complicates the detection of defects.Because of this, a study was made of how the noise related to factors such as steel grade, temperature, size and Velocity. By observing the signal and with the possibilities to change the equipment settings the capability to let a signal filter reduce the noise level were evaluated.

Glycogen is the storage form of glucose and is used by the skeletal musculature as energy both for intense and endurance events. The glycogen content in the horse?s middle gluteal muscle is more than 600 mmol/kg dry weight, and almost 400 mmol/kg dry weight in the human?s Vastus lateralis. In some special occasions, for example in competitions with several moments on following days, there is a need of a fast muscle glycogen resynthesis. The feed intake is of importance for the Velocity of the resynthesis.

Today small metal parts are mass-produced as for example rollers in cylinder bearings. At high Velocity cutting the metal is cut with a great force in a scissor-like device. Both precision and repeatability is important to be able to guarantee good quality, but from an economical point of view it is also important to keep a great manufacturing capacity. The part of the process that is most time consuming is when the metal bar, that is about to be cut, is fed to the right position. Therefore it is interesting to examine if the time used for positioning can be reduced.

Bakgrund: Venduplex har på senare år vuxit fram som den mest använda metoden vid diagnostik av venös insufficiens eftersom det är en ofarlig, kostnadseffektiv, non-invasiv metod med hög sensitivitet och specificitet där både den anatomiska placeringen av insufficiensen samt den funktionella förändringen av venen kan påvisas direkt vid undersökningen. Olika manövrar kan genomföras för att påfresta venklaffarna och därmed framkalla en eventuell reflux, men det är oklart om de olika manövrerna kan påverka den reflux som provoceras fram och därmed också påverkar bedömningen av insufficiensgraden.Syfte: Syftet med studien var att undersöka om det förelåg skillnad i graderingen av insufficiensen samt om den maximala refluxhastigheten påverkades beroende på vilken manöver som användes för att framkalla en reflux.Metod: 20 v. saphena magna mitt på låret med påvisad reflux deltog i studien. Två upprepade mätningar genomfördes där venklaffarna provocerades med hjälp av en blodtrycksmanschett över vaden, med en manuell kompression över låret samt med en manuell kompression över vaden.Resultat: Den maximala refluxhastigheten blev 0,33±0,20m/s när en blodtrycksmanschett över vaden användes, 0,31±0,22m/s när en manuell handkompression över vaden användes samt 0,17±0,16m/s när en manuell lårkompression genomfördes.Slutsats: Ingen signifikant skillnad på maximal refluxhastighet kunde konstateras när en automatisk uppblåsbar blodtrycksmanschett över vaden jämfördes med en manuell handkompression över vaden. En signifikant högre maximal refluxhastighet konstaterades när en manuell vadkompression jämfördes med en manuell lårkompression..

The purpose of this thesis is to analyze and identify a selected number of key factors in successfully implementing open innovation. More precisely, it looks at how value is maximized using open innovation practices. The scientific approach taken is based largely on the network perspective, which puts relations to other companies in focus. An extended view of the resource based view (RBV), different from the traditional one by taking also external resources into account, is in addition central to understanding the use of external resources to create internal value. The two main research questions strive to look at how the company locates relevant partners and what the relations that are established with these partners should look like to get the most of open innovation.