The Swedish government has set up the overall goal that no net emissions of greenhouse gases can occur after 2050. A sub-target has been developed for road transports which states that the use of fossil fuels must be reduced with 80% to 2030 in order to be completely abolished to 2050. A public inquiry mapping how this can be achieved was handed in to the government late in 2013. The use of alternative fuels for road transport, both biofuels and electricity, is expected to give the biggest contribution to the reduction of the use of fossil fuels. The inquiry sets up a number of goals for how much the use of alternative fuels must increase to 2030 in order to reach the overall goal and which instruments that are needed in order to do so.The aim of this thesis is to evaluate how these goals can be reached and what the most likely obstacles that may hinder the reaching of these goals may be.

SammanfattningDetta examensarbete, som har utförts på Scania CV (Commercial Vehicles)AB, undersöker hur de kan minimera den planerade nertiden för webbservrarnahosScania Fleet Management System ett system som har en webbportaldär kunderna kan se specik information om sina fordon. I dagsläget tassystemet ner vid systemunderhåll, vilket gör att kunderna inte har åtkomst tillsystemet under tiden. Intervjuer genomfördes för att få en uppfattning om hurandra företag löst liknande problem. Det undersöktes även om användningenav molntjänster skulle kunna lösa problemet och hur det skulle vara möjligtatt göra uppgraderingar utan att användarnas sessioner bryts. Resultatet somframkom var att den arkitektur som rekommenderades oftast är att ha någonform av klustrad lösning med lastbalanserare för webbservrarna.

In the coming years, organic food waste will be collected in the region of Gästrikland, Sweden. The collection is planned to cover the entire region by the end of year 2007. To start with, smaller amounts are being collected and transported to a central composting plant in Sala. However, a central composting plant in the region of Gästrikland is projected.The objective of this thesis is to evaluate a number of possible methods for composting of organic food wastes regarding their environmental impacts and localization.There are four scenarios for future composting of organic waste that have been evaluated. There are two that consist of membrane composting, either in Sala or in the region of Gästrikland.

The ferry traffic to Gotland is essential for the island?s ability to live and develop. Yearly, it transports 1,6 million passengers, 500 000 personal Vehicles and 750 000 lane meters of freight with four Ro-Pax ferries. The traffic is controlled and subsidized by the Swedish government since 1971 in order to guarantee the inhabitants and industry of Gotland a satisfactory transportation service. As a consequence of the past decades increased traffic quality, mainly due to a decrease in crossing times, the traffic?s environmental impact and costs has also increased.The Master Thesis proposes a new energy efficient traffic arrangement that satisfies the users? preferences in the same extent as today.

This master thesis has been carried out at Scania R&D at the department for Powertrain Control System Development during the winter of 2010/2011. In the thesis the writer examine and evaluate the existing method for collecting information from the tests carried out during the development of the Powertrain Control Systems software. It also contains suggestions for how a new method that enhance the validation elements could look like.The master thesis uses Vicentes theories of the ecological approach and theories of how knowledge sharing of tacit and technical information works within an organization and between the organization and its customers. First a workplace analysis at Scania R&D is carried out to see how Powertrain Control Systems work and how they test their software. Second a control task analysis, where the aims decided on after the interviews, is compared to the existing method.

Biogas is a renewable fuel that can be extracted from anaerobic digestion of many differentsubstrates, for example biological household waste. An alternative handling of the waste is tomix it with other wastes and incinerate it in a combined heat and power (CHP) plant. Thisstudy uses life cycle assessment to investigate which type of waste handling that is betterfrom an environmental point of view, anaerobic digestion with biogas production orincineration. The results are based on a case study of a biogas production plant owned by thecompany Ragn-Sells in Vänersborg. The alternative is incineration at a CHP plant inGothenburg.

This report is a description of a developed educational simulator over rail Vehicles and its components. The simulator is a hardware-based prototype over a door system on rail vehi- cles. System specialists and technicians will use the prototype. The Simulator should give the user a technical demonstration on how components work in a door system. The proto- type consists of motor, switch, relay and sensor.

Due to increasing regulations regarding new diesel Vehicles particulate matteremissions the new Scania truck, Scania Euro 6, has been equipped with a particulatefilter. This component effectively stores the particles in the exhaust gas but must becleaned in order to prevent itself from clogging. The filter is cleaned through aprocess named regeneration which is a thermodynamic process in which thetemperature of the filter is raised through fuel supplied to the exhaust gas.The purpose of this thesis is to contribute to the development of improved controlstrategies of the temperature during the regeneration process through thedevelopment of model-based controllers. These controllers are designed in order tohave good performance in stationary as well as automatic regeneration.In order to develop these model-based controllers a model of the system isconstructed. The model is described as a linear thermodynamic grey-box model withflow varying parameters, showing good results in validation.The model provides a simulation environment during the controller design, which isfocused around the development of linear regulators with the exhaust gas mass flowas a scheduling variable whose size determines controllers? mode of operation.

This thesis is a feasibility study for a future product development project. The purpose ofthis project is to evaluate the possibilities and difficulties associated with the design of anelectric power assist servo for all terrain Vehicles (ATVs). The project has been carriedout in collaboration with Nira Control AB. Nira designs and manufactures electric andelectro mechanic products mainly for the motor sport market segment.Nira Control AB is developing a fuel injection system for a new line of large ATVs oncommission. To be able to compete with manufacturers like Yamaha and Honda thecommissioner should be able to offer optional power assist steering.

This report is a description of a developed educational simulator over rail Vehicles and its components. The simulator is a hardware-based prototype over a door system on rail vehi- cles. System specialists and technicians will use the prototype. The Simulator should give the user a technical demonstration on how components work in a door system. The proto- type consists of motor, switch, relay and sensor.

The building and plant sectors represent a large part of Sweden?s energy use. Putting energy requirements in public procurement as a tool for reducing energy consumption in the building and plant sectors is therefor an opportunity that operators can take advantage of. The aim of this thesis was to map the energy requirements in procurement that operators in the public sector use today in building and plant projects. The analysis was made with respect to if the energy requirements corresponded to the parts with large energy use in building and plant projects and also in which way energy requirements in procurement are written in the contract.

 With the increases in fuel costs due to the depletion of the world oil reserves and the increase of greenhouse gasses as a consequence to using oil as a fuel many companies are looking to new and innovative ways to power their aircraft. One of these new ways to power an aircraft is using fuel cells powered using hydrogen and oxygen, thus producing nothing but water vapour and small amounts of nitrogen dioxide as well as trace amounts of other emissions. Both Boeing (1) and Politecnico di Torino (2) have shown that it is possible to build an all-electric aircraft powered by fuel cells. Both flights used small, two-seater aircraft and a constant between them was the loss of the co-pilot seat due to weight and lack of space. As this paper will deal with a commercial aircraft a primary concern is the cargo and passenger capacity and whatever impact switching propulsion system has on these.

Due to increasing regulations regarding new diesel Vehicles particulate matteremissions the new Scania truck, Scania Euro 6, has been equipped with a particulatefilter. This component effectively stores the particles in the exhaust gas but must becleaned in order to prevent itself from clogging. The filter is cleaned through aprocess named regeneration which is a thermodynamic process in which thetemperature of the filter is raised through fuel supplied to the exhaust gas.The purpose of this thesis is to contribute to the development of improved controlstrategies of the temperature during the regeneration process through thedevelopment of model-based controllers. These controllers are designed in order tohave good performance in stationary as well as automatic regeneration.In order to develop these model-based controllers a model of the system isconstructed. The model is described as a linear thermodynamic grey-box model withflow varying parameters, showing good results in validation.The model provides a simulation environment during the controller design, which isfocused around the development of linear regulators with the exhaust gas mass flowas a scheduling variable whose size determines controllers? mode of operation.

Målet med detta arbete är att hitta en lämplig lösning för lastsimulering vid test av bussar.Projektet utfördes i samarbete med Laxå Special Vehicles (LSV) som ska bygga entestbuss åt Scania.Scania har tidigare en testbuss med ett lastsystem som ska bytas ut när det ska byggasen ny testbuss. Uppgiften i detta arbete blir att ta fram och utveckla ett helt nytt lastsystemför den nya testbussen. Information om den buss som ska byggas har samlats in ochutifrån detta har via brainstorming framkommit flera möjliga lösningar som sedan harutvärderats.Metodiken som projektet arbetat efter är systematisk konstruktion enligt Johannesson,Persson och Pettersson (2004). Denna metod kan delas in i fem steg,Produktspecifikation, Konceptgenerering, Utvärdera koncept, Detaljkonstruktion ochslutkonstruktion.Det lastsystem som Scania använder idag har några nackdelar, bland annat att det ärbesvärligt att ställa om systemet från ett lastläge till ett annat. Samt att det under vinternär problem med att systemet fryser då systemet använder sig utav vatten somviktmedium.Ett av de lösningskoncept som tagits fram valdes att arbeta vidare med till enslutkonstruktion.

Aqeri has since the past year a new profile with name and logotype, which has createda need for an updated visual product identity. The company is a leading developer,producer and distributer of IT products suitable for extreme environments in industry,defense and Vehicles. This new profile with the different segments has together with aproduct identity from two companies resulted in that they have no clear designidentity on their products. From this background the aim of this research is todetermine how a development of a design identity is done to implement it to Aqeri.The design identity can be defined as a product?s identity visualized through its formor appearance which defines what the product is.