The goals of this Bachelors? Thesis were to establish the production loss through the VTIS1 Pasteur at Arla Foods Linköping dairy and then suggest simple but effective solutions to minimize the losses for each production run. If the timeframe allowed it, some of the solutions would be implemented and tested in full production to determine their impact on economic and environmental savings.The very first step of this project was to establish the statistics over what losses there is in the production pipeline through VTIS1, from milk and powders in mixer tanks to finished and packed products in cold storage. Then, when knowing how much product was actually lost and where, those bottlenecks could be pinpointed and examined more closely. At this stage the focus was switched, from the otherwise complicated and broad manufacturing process, to the VTIS1-aggregate, since early data indicated there were quite substantial losses there.In conjunction with this project Arla Foods purchased an absorption photometer-measuring device (OPTEK AS16) that could be inserted straight into the product stream out of VTIS1, allowing real time measurements of its optical density.

A proposal of a new path from the inner town of Gävle to a small cultural area in the seaside. The thesis contains historical background, analysis over town and the area, and a proposal of a new shape for the postindustrial area near the stream called Gavleån. .

From the customer?s perspective the only reason for a firm to exist is the value it creates. However, a problem within manufacturing companies is that of the total lead time, only a small part can be considered as value adding. It has further been discovered that when working with improvements businesses often sub-optimizes single processes instead of considering what benefits the entire company. Thus, when improving processes and activities it is important to have knowledge about and understand which factors that affect how the flow can be designed.Several studies have been performed with a wide perspective on process flows in order to obtain a more resource-efficient and value added flow.

Considering water quality, landuse and reducion of wetland area in the watershed of Tidan, areas witch are in need of constructions to improve the water quality are identified. Constructions are suggested to be located within the smaller streams in the watershed, so that the water is treated before it reaches the stream Tidan..

AbstractPaper in political science, C-level, by Lars A Roos, spring semester 2007. Tutor: Susan Marton. ?Policy networks and Nord Stream.?The purpose of this paper is to examine how the government and interest groups have been working together to commonly prevent the building of a gas pipeline in the Baltic Sea. To do this, a comprehensive question how does the government and the involved interest groups work together in policy networks? has been broken down to three more specific questions: (1) Can the cooperation between the government and the interest groups be placed within the frame of a issue network or a policy community? (2) Has the cooperation between the government and the interest groups contributed to new tools for the government to prevent the gas pipeline? (3) If the answer is yes to the second question then, which are these new tools?My examination is a case study of the policy network that exists around the Swedish actors in the case of the Baltic Sea gas pipeline.

För att göra informationen tydligare för en larmoperatör som sitter och övervakar larm som kommer in från ett antal olika nätverkskomponenter så har vi skapat ett system som förser larmen med extra information, kallad Context Type, så att vi kan presentera larmen på ett enklare sätt. Vår informationsberikning, även kallad mappning, är utbyggbar för att möta kravet på framtida utveckling. En webbaserad klient skriven i JavaScript är skapad för att presentera larmen på ett nytt innovativt sätt som är baserad på context typen istället för larmobjektet. Mappningen är skapad med hjälp av Python kod och begränsas av att endast använda textfiler som datakälla och webbapplikationen är endast utvecklad för webbläsaren FireFox samt att visningsintervallet för larmen är begränsat till ett dygn med entimmesintervaller. Mappningen var långsam då vi använde oss av regular expression.

This thesis have been performed at Sweco Position in Jönköping. The work was split into two, where one part included an investigation regarding the possibility of developing a cross-platform GIS (geographic information system) with HTML5 and CSS3. A prototype would also be developed within this part.The second part included development of a cross-platform GIS for a client to Sweco Position. The client operates in the forest sector and had already an existing solution, with many problems. The client required an application with delimited functionality and which was not bound to a specific hardware.As the client users often were located in areas with limited Internet access, one additional requirement was that there would be some offline support.The students handle subjects within development of GIS, for example map projections, map services and mapping libraries.The application came to be developed in HTML5 and ASP.net.

How can you do a right measurement of culture as well as with other social sectors and with what can culture contribute when it comes to a town´s development? We found out that in Linköping the regional federation Ostsam recently (2005) started mapping the region's creative centers in order to look into the spreading of the culture in the county, and then use the uniqueness of the culture as an advantage in society- planning contexts. The reason was that both municipal - and State directions detected that the culture has a broader importance when it comes to building up society and infrastructure than earlier considered. This is called Cultural planning and is the foundation- method that Östsam used when working with their new projekt The creative sector. The outcome of the Östsam study resulted in an exciting study basis to work further on with and to examine through own demarcations and directions.This research manages the matter of the creative sector as an extension to the cultural sector.

This master thesis includes a description of how a number of sensors are put together in a sensor platform. It also gives a description of how localization and mapping has been performed with data collected from the sensor platform. Localization is a prerequisite for most of the tasks that can be requested from an autonomous mobile robot. In many situations the GPS signal is not available and hence an additional localization system is required. One approach is to apply localization based on landmarks extracted from the robots surrounding.

The Smart Grids development is driven by forces concerning safe electrictransmission done in an energy efficient way. Vattenfall Eldistribution AB has a visionto transform their electricity network into Smart Grids. To invest in Smart Grids theyhave a need to show their customers what advantages they will get from thedevelopment. This led to the formulation of this dissertation project where the aim isto identify products and services related to Smart Grids that will increase thecustomer satisfaction for Vattenfall Eldistributions private customers.The project started with a mapping of existing products and services on the Swedishelectricity market. From the mapping several development possibilities for VattenfallEldistribution were identified.

Syftet med studien är att få en förståelse för hur utrustningseffektiviteten kan mätas i ett producerande företag. Vår studie utförs på ett företag i Alvesta som heter Gnutti Powertrain AB som bland annat tillverkar precisionskomponenter till motorer.Genom att vi skapar en analysmodell utifrån studerade teorier beskrivs ett systematiskt tillvägagångssätt som slutligen ska leda till att syftet uppnås. Utifrån analysmodellen studeras och beskrivs först Gnutti Powertrain AB´s nuvarande tillvägagångssätt för att sedan jämföras och analyseras gentemot de studerade teorierna. Med hjälp av analysmodellen struktureras också vår studie på företaget och vårt utförande och resultat utifrån detta kommer sedan att presenteras.Analysmodellen nämner att en processkartläggning först ska göras. I processkartläggningen väljs först en specifik process ut, vilken i vårt fall blev produktionsprocessen för en rulle av stål.

In a time when milk producing farm businesses face decline in profitability it is of great importance to examine how the situation can be improved. This thesis is a study off efficiency in milk producing farm businesses represented by Swedish, Dutch and German farms. The aim of this study is to investigate whether any differences exist between companies in these countries. Moreover, the study includes a mapping of a number of factors that determine how efficient milk production can be managed. This mapping is based on a literature review on prior efficiency studies followed by qualitative interviews with milk production advisors as well as a questionnaire sent out to dairy farmers in Sweden.

AB Sandvik Cormorant?s production unit in Gimo has identified a need to examinethe handling of products between operations with the purpose of generatingproposals of improvement for the product handling.The aim of this project is to study the existing manufacturing process and givesuggestions for improvement. The proposals should reduce the manual handling ofproducts, decrease the risk of damaging the products during the manufacturing andform a basis for increased traceability. Based on a mapping of the manufacturingprocess and the problem description, a specification of requirements has beencomposed.The mapping of the manufacturing process suggests that a change of the currentsystem is required. The company is recommended to decide how the producthandling between operations should be performed as guidelines for the productionteam.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.