The goal of this project was to together with Cochlear Bone Anchored Solutions AB develop a new cleaning tool for their Baha?systems. Cochlear BAS AB is a daughter company to Cochlear Limited based in Sydney, Australia. Cochlear BAS AB is situated in Gothenburg and with its 150 employees develop and manufacture the Baha?system.

This rapport contains an examination of the energy consumption of a kindergarten, which areas that have the largest impact on the energy consumption and what can be done to reduce those areas in ways that are relatively easy and profitable. It is also analyzed if it is possible to reduce the energy consumption from today?s consumption to a consumption that fulfils the demands placed on low energy houses by FEBY.The focus has been on reducing the energy consumption of the areas ventilation, heating system and hot water system, since those seemed to be the easiest ones to affect and since the building is quite recently built.There are different kinds of ventilation systems, at the moment the building have a CAV-system, which means that the ventilation is too high during large parts of the day. There are different ways to manage the ventilation system, for example presence detection, humidity sensors, CO2 sensors, temperature sensors and season adjustment. Many of those are in the end dependent on CO2 sensors to guarantee a good indoor climate, therefore the focus have been placed on this system.

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

This report shows the process of the development of a sensor module for the seed drills of Väderstad Verken AB. The module is supposed to replace existing solutions, provided that it is better from both a constructional- and an economical aspect. The purpose of the sensor is to continuously give the driver information about the level of height of the front- and drilling tools and the main purpose of the sensor is to allow the seeds to be placed at the desired depth. The sensors which have been taken into consideration have all been of an analogue type and have a protection class of minimum IP67.The methods applied have been taken from the book ?The Mechanical Design Process? by David G.

The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.

This report is a bachelor thesis presented at the department of Computer Science andEngineering at Chalmers University of Technology. The aim for the project is to find a simplemethod to measure and display physical quantities in a three dimensional room.The report describes a method to construct a system for measuring differentphysical quantities via sensors. The system must be built in a modular and expandable way tobe adaptable to different tasks.The system explained in the report consists of two parts;A physical scanner with moveable probes for carrying sensors and a microcontroller forcontrolling the probes and communicating with the next part.An application written in Java for storing the measured values and presenting them in a lucidperspective.It is possible to construct the scanner with different designs and circuitry, with multiplexers andflip-flops, to ensure that an unspecified number of probes can be added to the system and thatthey can be operated simultaneously.The Java application is written in a modular way, using a design pattern that separates eachindividual part of the application. It contains exceptions and interfaces that ensure a safe andexpandable application..

This report is a bachelor thesis presented at the department of Computer Science andEngineering at Chalmers University of Technology. The aim for the project is to find a simplemethod to measure and display physical quantities in a three dimensional room.The report describes a method to construct a system for measuring differentphysical quantities via sensors. The system must be built in a modular and expandable way tobe adaptable to different tasks.The system explained in the report consists of two parts;A physical scanner with moveable probes for carrying sensors and a microcontroller forcontrolling the probes and communicating with the next part.An application written in Java for storing the measured values and presenting them in a lucidperspective.It is possible to construct the scanner with different designs and circuitry, with multiplexers andflip-flops, to ensure that an unspecified number of probes can be added to the system and thatthey can be operated simultaneously.The Java application is written in a modular way, using a design pattern that separates eachindividual part of the application. It contains exceptions and interfaces that ensure a safe andexpandable application..

Electronic article surveillance (EAS) is widely used in shops and libraries together with an RF-tag attached to the goods or books in order to prevent shoplifting. By implementing the addition of a moisture sensor to the RF-tag, other functions become possible, including the ability to use as an alarm with regards to frozen goods, which have been shipped but which have melted and have, subsequently, refrozen. In- relation to care for the elderly, one time-consuming step involves checking whether there is the necessity for a change of diaper and this can, instead, be based on an RF-tag with an EAS-system alarm. A preliminary investigation was made using the moisture sensors, which involved how the resistance changes when liquid and/or heat is applied. A simulation of the LCCR circuit (RF-tag with the sensor) was conducted in order to determine how the resonance frequency changes for different resistances levels.

The aim of the Master?s Thesis work is to study and develop algorithms for autonomous travel of a UGV (Unmanned Ground Vehicle). A vehicle for the mounting of sensors has been constructed in order to perform the work. Since the UGV is to be used outdoor in urban areas, GPS can be used. To improve precision and robustness, inertial navigation is used in addition to GPS, since GPS reception is likely to be diminished in such areas.

Rapid Granulator is one of the world's largest producers of granulators, which is a kind of grinderwho grinds discarded plastics to granules which later can be reused when pressure molding plastics.The company wanted help in developing a new, or alternatively extending their previous,measurement equipment. The old equipment was hard to use, required changes in the code fordifferent measurement scenarios and had a limited array of measuring quantities. Rapid had an ideaof a similar concept only with a greater number of input ports, better range of applicable sensors andan advanced yet easy to use interface. The system is supposed to be placed at Rapid's test departmentwhere it will be used as a tool for finding faults and provide data which can be used for furtherdevelopment of the granulators.The project's members accepted the task and immediately began searching for suitable componentsfor the system. After the search was completed a list of costs, limitations, sensors, I/O's anddevelopment environment was presented to Rapid's staff.

This report is a bachelor thesis presented at the department of Computer Science andEngineering at Chalmers University of Technology. The aim for the project is to find a simplemethod to measure and display physical quantities in a three dimensional room.The report describes a method to construct a system for measuring differentphysical quantities via sensors. The system must be built in a modular and expandable way tobe adaptable to different tasks.The system explained in the report consists of two parts;A physical scanner with moveable probes for carrying sensors and a microcontroller forcontrolling the probes and communicating with the next part.An application written in Java for storing the measured values and presenting them in a lucidperspective.It is possible to construct the scanner with different designs and circuitry, with multiplexers andflip-flops, to ensure that an unspecified number of probes can be added to the system and thatthey can be operated simultaneously.The Java application is written in a modular way, using a design pattern that separates eachindividual part of the application. It contains exceptions and interfaces that ensure a safe andexpandable application..

AbstractA continuous improvement of products and production is an important goal for a modern industrial company. A small engineering group located in Sweden came in touch with the authors of this report during the spring semester of 2014. The aim of this report is, as part of the group´s ambition of improvement, to analyse ways in which the quality of component casted parts can be verified. Non-destructive testing (NDT), and methods to use it for quality control, is the main focus of this report. However, fields such as material standards, component casting and quality engineering are analysed as well.

During test flights SAAB uses the data acquisition system COMET 16. The part of the system that receives the signals from the sensors and converts them is called KSM 15. The purpose of this thesis is to develop a data acquisition module on stacked PC/104 modules with a lower production cost. Our work has been divided into one part about analog signal conditioning and a second part with digital filtering and memory management of the sampled data. The analog part, designed of regular components like instrument amplifiers, voltage references, operational amplifiers and multiplexers, adjusts the sensors signal levels for the ADC?s that converts the signals.

This report is the result of a diploma work made at IMT at US in Linköping. The purpose of this piece of work is to investigate the possibility to design a general program for data-acquisition using LabVIEW, suiting different hardwares and connections. Great importance has been attached to communication with serialport, using bluetooth, because different wireless PPG-instruments has been developed parallel to this project. These PPG-circuits uses this type of serialcommunication. Communication with USB, GPIB and analog connection has also been examined and analog communication has been tested practically.

In industries today the demand for reading the state of industrial equipment and thus prevent machine breakdown, is increasing. The company HMS Industrial Networks AB has a product on the market, Netbiter EC350 that is used to read sensors and thus find out the condition of industrial equipment. By reporting scanned data to users through a cloud service, users can keep track of their equipment. When developing Netbiter EC350 a slot was made for a Bluetooth module to offer clients a wireless reading in future developments. In this project a prototype was made to show how this Bluetooth communication can be implemented. The goal of the project was to create a Bluetooth communication between a Bluetooth sensor and Netbiter EC350. A user interface was made to allow the user to read sensor values. The result of the project shows how a Bluetooth communication can be implemented to read sensors wireless and therefore it fulfills its purpose and goal.