In this bachelor thesis, diagnostic methods for one of Siemens stem inlet control valves have been developed. The work has taken place during ten weeks at Siemens Industrial Turbomachinery AB in Finspång. The company produce steam- and gas Turbines and also provides service and maintenance. The purpose with this project has been to develop diagnostic methods that oversee the health of the control valves. By using the developed methods you will know when it?s time for maintenance.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

AbstractThis report describes our ten week long thesis work which is the last task in our education in mechanical engineering at Linköpings University. The project has been performed at Siemens Industrial Turbomachinery AB?s service department. The company which is located in Finspång produces, sells and provides service for steam and gas Turbines around the world.The purpose of this project is to help Siemens develop their maintenance programs for two of the auxiliary systems which are a part of the complete steam turbine system. These are lube and control oil systems.The project is restricted to two of Siemens maintenance products, No Stop Check (NSC) and the annual Safety Inspection (SI).

This report describes the results of the project "Concept development of jet engine inspection plugs" carried out in the spring of 2008. The work was done at the department of product definition at the company Volvo Aero in Trollhättan. The objective of the work was to develop concepts for a "Volvo-unique" inspection plug. The work is part of Volvo Aero's focus on proprietary (self-developed) technologies. Inspection plugs can be found on virtually all aircraft engines and gas Turbines.

This rapport contains an examination of the energy consumption of a kindergarten, which areas that have the largest impact on the energy consumption and what can be done to reduce those areas in ways that are relatively easy and profitable. It is also analyzed if it is possible to reduce the energy consumption from today?s consumption to a consumption that fulfils the demands placed on low energy houses by FEBY.The focus has been on reducing the energy consumption of the areas ventilation, heating system and hot water system, since those seemed to be the easiest ones to affect and since the building is quite recently built.There are different kinds of ventilation systems, at the moment the building have a CAV-system, which means that the ventilation is too high during large parts of the day. There are different ways to manage the ventilation system, for example presence detection, humidity sensors, CO2 sensors, temperature sensors and season adjustment. Many of those are in the end dependent on CO2 sensors to guarantee a good indoor climate, therefore the focus have been placed on this system.

A large number of rivers in northern Sweden have hydropower developments that cause negative effects on both up- and downstream migrations of anadromous species like Atlantic salmon. So far, most attention has focused on the hindrances of adult fish during their upstream spawning migration. However, since Turbines in power stations cause losses on downstream passing fish, the focus on negative effects on smolts has increased. The aim of this study was to compare three different causes of losses of salmon smolts passing downstream through a power station area in the flow-controlled River Åbyälven in northern Sweden.A total of 61 wild salmon smolts were caught and radio-tagged in the River Åbyälven during their downstream migration in June 2009. The salmon smolts were released at three locations, 1.1 km upstream from the power station, in the turbine intake and in the upper part of a fishway, acting both for up- and downstream fish passage.

AbstractThis thesis is the final part of the Innovation and Design Engineering Programme (180 ECTS credits)at the Faculty of Health, Nature and Engineering Science at Karlstad University. The extent of thisthesis is 22.5 ECTS credits and has been performed independently by Hannes Jernberg during thespring of 2013. Metso Paper Karlstad AB is the task maker of this project, and Arvid Johansson is thecompany Representative. Metso Paper Karlstad AB is one of the world leading developer andmanufacturer of tissue paper machines.In the current situation, the company has developed and patented a power management systembased on a Cross Flow Turbine. The current construction is limited to a paper width of 2.9 meters.The company wants to take advantage of all the opportunities provided by the patents, to develop aturbine solution paper machine with a paper width that is wider than 5.5 meters, and give the abilityto manufacture paper for lower energy consumption which is an important part of the production asit is very energy intensive.Problems arise with the increasing length of the turbine, ultimately resulting in that the deflectionbecomes too big and that the momentums, due to the increased torque the turbine blades breaks.By applying the design process, this work has resulted in a number of potential solutions to theproblem.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

As a consequence of increasing wind power installations in the Nordic grid the last years, the need for regulating power has become larger. In the Nordic grid, regulating power is mainly provided by hydro power. One part of the regulating power is called frequency control, which ensures that the grid frequency is stable and close to 50 Hz.However, setting the turbine into frequency controlled operation may cause stress and wear of the components in the mechanical control system. Frequency controlling implies large and frequent servo forces and longer travelling distance of the sliding bearings in the Kaplan turbine.Based on one selected Kaplan turbine, Selsfors G1, measurements and MATLAB calculations have been performed in order to determine forces and movements of the linkage system. With these forces and movements as input, stresses and fatigue have been determined as well as sliding distances, bearing pressures and wear of bearings during a typical lifetime of 40 years.The results indicate that no severe wear exists on the bearings during 40 years of service.

Vattenkraftstationer, med dammar och turbiner, utgör hinder för nedströmsvandrande smolt. Syftet med denna studie var att undersöka turbindödligheten för öringsmolt (Salmo trutta) vid två kraftstationer, de befintliga ytlänsarnas avledningseffekt och om effekten kunde förstärkas genom mörkläggning i form av övertäckning av kraftkanalen med en presenning vid turbinintaget. Utöver detta var avsikten även att undersöka om det fanns något samband mellan smoltgrad och smoltens förmåga att förflytta sig mot havet. I Emån i Småland fångades 46 öringsmolt som radiomärktes och sattes ut vid två kraftstationer och pejlades dagligen i sex veckor. Det var en större dödlighet vid den övre stationen än vid den nedre.

When planning new wind farms, the cost for the internal electrical grid is estimated to account for 8-9 % of the total investment cost. On top of that, the cost for accumulated reduced income over several years (due to electrical losses), has to be added. The economic lifespan is relatively long (about 20 years) which means that an error in the loss calculation could lead to a bad decision basis. The accumulated reduced incomes due to electrical losses can be higher than the initial investment cost for the internal electrical grid.Today, Statkraft Sweden is using a template number when estimating the electrical losses in a wind farm. The actual losses are probably lower than the template number which could lead to an unnecessary high loss cost when planning a new wind farm.The aim of this M.Sc.

In this thesis a method for evaluating investments in small scale hydro power is presented. An analysis of the future position that small scale hydro production will have on the Nordic electricity market is also carried out. This is done by an inventory of technology and economic and environmental aspects. The inventory is also a guide as to how the project should be implemented.Hydrolyzer is the name of the Excel tool developed to evaluate investments. The tool requests input data from the user and then evaluates the investment and generates a sensitivity analysis.

Wind power is an energy source that is becoming increasingly popular in Sweden and around the world. The establishment of large wind farms supply and contributes to energy production within grid in search of a more sustainable energy production. Wind power is becoming more popular and opens up new areas of implementation. More cities are starting to use small-scale urban wind power, everything from full-scale work for a little less work adapted to the villas. Sweden has high goals regarding the production of green electricity and the work which deals with the conditions Sweden plays in achieving those goals.

Intresset för småskaliga vindkraftverk på byggnader har ökat under de senaste åren. Allt fler människor blir mer energi- och miljömedvetna samt ser fördelarna med att elektriciteten produceras där den konsumeras; i den bebyggda miljön.Det är dock en större utmaning att installera ett vindkraftverk i urban miljö, jämfört med i öppet landskap, då det finns många faktorer som skall beaktas. Stadens komplexa uppbyggnad gör att vindens hastighet och riktning varierar och ger upphov till turbulenta strukturer i den omgivande luften. Många av dagens vindkraftverk kan ej operera effektivt vid turbulens, därför måste dessa vindkraftverken placeras på höga höjder för att nå den laminärt strömmande vinden över staden, vilket ger orealistiska längder på de master som krävs, även om vindkraftverket monteras på en byggnad. För att kunna utnyttja de vindar som uppkommer i urbana miljöer bör vertikalaxlade vindkraftverk med en helixformad geometri på rotorn användas.

In connection with the property crises in many countries, caused by the financial crises, people are now more aware of the risks involved in poor property-investments. The unusually cold winters along with extreme prices of electricity in Sweden in recent years has also contributed to increased interest in energy-efficient buildings.The process of developing a modern family home in Kiruna, Sweden is presented the first part of this paper. The house has been designed to withstand very high stresses from snow, low energy consumption as well as a high standard of living comfort. Aspects of the house covered here involves everything from construction, heating and ventilation to sanitation. Each of these areas is presented based on their underlying, scientific methods or theories.