The aim of this report is to improve the fire safety at Hallsta Paper Mill in Hallstavik, Sweden. In order to do so large parts of a fire-protection management system for the paper mill has been created. The report begins with giving a general description of management structures and fire-protection management systems. An account is given for how management structures are designed, and how they should be implemented, maintained and updated. Thereafter follows a description of what routines and instructions should be included in a fire-protection management system..

Det här arbetet omfattar en arkitekturstudie av ett framtida processnät för Hylte Mill. Arkitekturstudien innefattar en mall för hur den framtida miljön kan se ut. Arkitekturhypotesen skall användas som en modell för företaget och visualisera ett trådlöst nätverkssystem vilket skall hjälpa operatörer att hämta information från SCADA-systemen via pekplattor. Metoden som använts för att ta fram arkitekturen grundar sig på utformningen av så kallade vypunkter. Vypunkter är vyer som skapas för att identifiera relationen mellan olika användare och systemet.

The purpose of this master thesis was to study the water system for mechanically cleaned water at Skärblacka mill, in order to find and evaluate possibilities of using energy more efficiently. The thesis also includes an evaluation of the software tool ?Pumpanalys?Skärblacka mill produces pulp and paper. The large amount of water required is cleaned mechanically through filters and called mechanically cleaned water (MR0). The MR0 water is pumped out to the factory by four crude water pumps.

Competition of spruce fiber raw materials has increased dramatically in the last few years, leading to the fact that transportation costs in the current situation represents a much larger share of the total raw material cost. The Holmen-owned pulp industry Hallsta Paper Mill's location on the coast also constitutes a problem, because of the lack of raw material, which is much larger there, than for a pulp mill located in the hinterland. For a coastal industry it?s therefore natural to import much of the raw material by boat or to buy it from the timber terminals, in order to maintain good profitability. The purpose of this study was to analyze how the size of Hallsta Paper Mill timber supply area, without competition, with competition and with terminal use, affects the company ?s transport costs.

Today's society is facing major challenges. In order to reduce the climate impact fossil fuels should be replaced with fuels that do not contribute to the greenhouse effect. The growing population generates organic waste originating from industry and households so called organic fraction of municipal solid waste (OFMSW). Through anaerobic digestion, waste can be utilized to produce energy-rich methane gas. In this way, waste can be a resource instead of a burden on society.

The report is part of the university´engineer program within Industrial Organization and Economics with specialization in Logistics and Managment at Jönköping´s university.Skoghall´s mill underlies a large supply chain, which means there should be a lot of areas in need of small improvement measures. This report illustrates a small part of one of these areas and is focused on the loading distribution services in the terminal Vänern.At the moment there´s a very unequal load of the load carriers SECU box and Container at the terminal. Skoghall´s mill has the desire to equalize the high and low load levels of the 2 loading carriers named previously. One of the options to solve the problem is to set a limit of how much the carriers can load per week or per day. The mill also wants it to be investigated if the proposition would influence the customers in any way and if both the company and its customers could handle a lower level of delivery services in case the proposition was to be applied.The goal to be achieved with this thesis is to provide balance to the unequall loading of the 2 load carriers, SECU and Container, and investigate whether or not the Skoghall´s mill´s customers, could manage the lower degree of delivery service that the proposition would imply.For this goal to be achieved, random sample investigations were taken from orders of a customer that is provided with SECU load carriers and the same was made with a Container´s customer.

This study investigated the effects of rubber alley flooring on cow locomotion, claw and leg health, production, cleanliness, grooming behaviour and cow exclusion rate in a free stall herd. The study was conducted in a new dairy house with a rotary milking system, with a matched group of cows on traditional scraped concrete alleys used for comparison. All claws were trimmed and lesions recorded at the beginning and end of the 4-month study. Locomotion, claw and leg health, behaviour and hygiene were observed and scored at regular intervals during the study. The results showed that cows on rubber alley floors displayed significantly (p.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The milling process creates a wide range of particle sizes.

This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and hardness.

An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

The Effects of dietary biotin supplementation on hoof health in Swedish dairy cows - a controlled cohort field study. The aim of the present degree project was to investigate the effects of biotin supplementation on hoof health in dairy cows. The experiment was performed as a controlled cohort study in three commercial farms in western Sweden from January 2002 to October 2002. The cows were all housed in cubicle systems with transponder concentrate feeding systems. Within each farm the cows were allocated to either biotin or control treatment. The biotin groups received 20 mg of biotin per cow and day, starting 14 days before expected calving.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

An analysis of a specific application of anaerobic wastewater treatment at a pulp and board mill, Stora Enso Skoghall, was carried out. A literature study was done and effluent wastewater from CTMP pulp production was analyzed. The analysis consisted of a broad constituent analysis and an anaerobic treatment trial. Results from these test where used to calculate the treatment effectiveness and resulting energy potential at the mill.The literature study and constituent analysis showed that toxicity of the water to be treated, due to wood extractives and sulphur content, was of concern. Detoxification chemicals targeting these constituents where used in the anaerobic treatment trial.

KRAV-certified organic dairy herds generally have a lower milk yield than conventional dairy herds. A high-level of milk yield requires a feeding regime with high amounts of concentrates, a factor known to contribute to the development of claw lesions (Bergsten, C. 2003). The aim of this study was to compare claw health between organic and conventional dairy herds in free and tie stall systems. The number of herds from different domestic animal health associations was chosen in proportion to the association´s total portion of Swedish dairy producing herds of each type, respectively.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.