The aim of this study was to develop a simple model for calculating stock costs for bio fuel at Billerud Karlsborg and subsequently recommending a suitable stock level of bio fuel. The stock components considered in the model are GROT (branches and tops), bark, dry wood chips, raw wood chips from barking and sawdust. The calculations are based on a probability distribution of historical deviations between ordered and delivered volumes. The model presents two different ways to manage the supply in case of irregular deliveries. The first way is to stock enough volume to cover the deviations and the second way is to compensate with a quick purchase from the spot market (at extra high purchase prices).

This thesis examines the emissions costs of Swedish aviation and their degree of internalisation under current economic instruments. The results show that the degree of internalisation spans from practically zero for a long-haul flight to 6 per cent for a typical domestic flight, where the climate cost, including high-altitude impact, makes up the main part of the cost. To inform evaluation of the consequences of this underinternalisation, or attempts to correct for it using price instruments, the price and income elasticities of international leisure air travel from Sweden are estimated using household expenditure data and two different price measures. The resulting elasticities are very high ? 2.03 or 2.04 for the income elasticity and -2.53 or -1.88 for the price elasticity ? and should be interpreted cautiously due to data limitations, especially for the price elasticities.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

AbstractC-level essay in political science, by Frida Orlinder, spring semester 2008Supervisor: Susan Marton?Good contracting? ? A study of contracting in public procurement regarding the transportation of school children?Over the last decades models influenced by the market have been gaining influence in public administration all over the world. New Public Management has been presented as a theoretical ?shopping basket? from which concepts can be applied to the administration of municipal services. The purpose of this essay is to investigate in an explorative way how New Public Management (NPM) views contracting and the role of the internal customer in contracting.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Executive SummaryThis final thesis has examined the effects of an increased centralization and better coord­in­ation of the distribution logistics at ABB in Västerås. The company is today strongly decent­ralized and there is a minimum of collaboration between the 20 business units. This is why the questions were raised; how could the business units coordinate outbound logistic activities and what effects would that provide. The obj­ect­ive of this final thesis is to provide basic data for a future decision-making which desc­r­ibe these effects.The report has mapped out the factors that are important to ABB in an evaluation of their logistic activities and how the outbound logistics work today. The four factors are cost efficiency, delivery service, environmental impact and logistics capability.

This paper examines how organizations work with their recruitment. The organizations in thispaper are mined in the trade of recruiting and staffing. The paper will further influence howorganizations work or will work with recruiting through social medias. It describes therecruiting process in the traditional way and what costs it brings. The next part is a descriptionof network and the importance of networking in a general way.Our results demonstrate that social medias probably will stay as a complement to other moretraditional methods and will not be an own recruiting method.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.