AbstractThe Municipality Council decided in 2010 to develop a comprehensive energy efficiency strategy with financial and methodological support from Energimyndigheten (The Swedish Energy Agency). The strategy should include 3 major parts: an inventory of the 2009 energy use defining the current situation, the 2014 and 2020 goals for energy use, and an action plan for goal achievements. According to Energimyndigheten, the strategy must include all municipal administration premises, vehicles, and all majority-owned companies (as Laholmshem, the municipal housing company).The report describes the inventory work in order to obtain the 2009 energy use and the sources of information used. The inventory values are used as the base year values for the 2014 and 2020 goals. The inventory showed that information about the vehicles is dispersed in the municipal administration and no clear structure exists with respect to mileage and fuels used.

Because of increasing demand of power on Malmbanan the capacity of the existing wires which supply the trains must be increased. This increases the stress on the existing poles and for this reason the system for supplying the loads along the railway is to be removed from the poles and be replaced by some other system. This thesis is a study on a two-level low voltage (1 kV and 0.4 kV) electrical system with the aim to investigate if it can be an alternative to the system used today taking into account the voltages, fault currents and costs.In this thesis the following tasks have been performed:? Gathering of data? Description of basic theory? Loadow and fault current calculations of the system with MATLAB? Life Cycle Cost estimate of the system? Analysis and conclusions from the resultsThe results show that the new system can be an alternative to replace today's system. The simulations and calculations show that the voltage drop is at an acceptable level and that the fault currents are large enough to supply a safe disconnection if a fault occurs at the far end of the system..

In this thesis you will be able tofollow the design work of a drumtest. A tool that by having a rotatingdrum with equally positioned obstacleswill simulate the conditions a mountainbike rim will pass through.Initially there is a specification ofsome parameters and requirements thatthe design had to fulfill. There is alsosome brief background information aboutwhy a drum test is required for abicycle rim manufacturers and about thecompany Innolite Design AB that thisthesis is done for. After that itfollows an extract from conceptgeneration with the chosen concepts andsolutions but also some of the conceptsthat were not chosen.The thesis also contain a part where thereader cangain a deeper understanding of how thedesign works as well as some moredetailed facts about how the choice ofmaterials, their thicknesses, etc. havebeen made.

The current situation for Swedish grain farmers facing a situation with decreasing profitability makes it necessary for the farmers to find ways of increasing the margins in their grain growing. Decreasing profitabilities along with Lantmännens closing of grain elevators contribute to the necessity for farmers to invest in grain storing and drying at the farm. By investing in capacity for drying and storage of grain on the farm it is possible to recieve a higher price on the grain sold due to the possibility to sell when the price is higher compared to the harvesting season. An investment in grain drying and storage with a relatively low investment cost that recently has appeared on the Swedish market is the grain stir drying system. This study contains a comparison of an investment in a grain stir drying system where the grain is dried and stored in the same silo and a conventional drying and storage system.

Many corporations turn to IT-outsourcing to focus more on their core competence or to cut the IT-budget. There is one caveat, the costs presented at a first glance does not always present the entire truth. Instead the costs run deeper and so-called hidden costs exist beyond the contractual cost. Reducing these hidden costs may very well be crucial to the entire IT-outsourcing endeavor. However many firms are not aware of these costs and as such they have a reduced chance of success.

Detta examensarbete är ett vidareutvecklingsprojekt som har utförts i samarbete med Bombardier Transportation AB. Företaget är en världsledande tillverkare av spårbundna fordon och detta projekt behandlar bagagehyllan i deras passagerartåg Regina. Antalet tågresenärer har ökat i takt med den ökade miljömedvetenheten vilket har resulterat i hård konkurrens där pris och vikt spelar en avgörande roll. Examensarbetet har därför utförts med målet att reducera bagagehyllan till både vikt och kostnad.Fokus i examensarbetet ligger vid förstudie av tidigare dokument kring bagagehyllan så som analys av kravspecifikation, inköpslistor, underhållsinformation samt analys av bagagehyllans utformning genom studier av ritningar och befintlig hylla. Förstudien har visat på ett antal områden med potential för vikt och kostnadsreducering som till exempel alternativa leverantörer eller material samt förenklingar av konstruktioner och monteringsmetoder.Efter analys av ovan nämnda områden för vikt- och kostnadsreduktion har ett antal lösningar föreslagits.

The Swedish bank Handelsbanken has, according to their own way of measuring, been more successful than a weighted average of their competitors during the last 38 years. They have also handled the recent financial crisis, as well as the one in the 1990´s, better than most other banks. This paper studies their management control system at branch level in order to identify the controls which have been enforced to ensure that a low risk level is retained in the lending. The controls that have been identified are; (1) A decentralized organization with the offices as profit centers where the manager has restrictions regarding risk level and the results are measured as K/I (cost/revenue). (2) The absence of bonuses and individual follow-up regarding performance measurement.

In December 2008 the municipal council in Nybro, decided that the municipality shouldreduce the budget for food service. The budget should be reduced by 2 100 000 SEK.They decided that the children- and education committee, and the care committee would haveto lower their budget with 1 264 000 SEK respectively 636 000 SEK. The change have to bedone under two years, 60 % should be done under 2009 and 40 % under 2010.As a result of the decision, many kitchens have to become kitchens that only serve food, notcook it. This will result in preschool staff and nursing staff take over some of the tasks fromthe kitchen staff. The municipal council also decided that entrepreneurs could take over one(later two) cooking areas.A kitchen that serves food means that there isn?t any cooking involved.

Stump wood was used between 1850 and 1950 for production of tar and as firewood. In the 1950s the use decreased because of the introduction of the cheap fossil oil. In the 1970s stump wood became an interesting issue again as a raw material for the pulp industry. Stump lifting has today become a possible source for bioenergy. The objectives with this study were to investigate the productivity of stump lifting and stump extraction, and to analyse the economy.

Sigill Quality Systems has been certifying beef since the autumn of 2006 using the brand name label Swedish Sigill. IP Sigill (the certifying system for integrated production) encompasses the values: animal ethics, food safety, free range and environmental concerns. Product quality is not yet one of these values, and there is a variation in the quality of Swedish beef. Swedish Sigill wanted to investigate the factors that influence product quality, review which of the present regulations that have an influence on product quality and formulate new regulations with the purpose of enhancing the product quality (sensorial, technological and nutritional quality). A survey of quality parameters and factors that influence product quality was done in order to establish a scientific foundation to work from.

Detta arbete presenterar enmatematisk optimeringsmodell gällande val av Prefableverantör för Spinactor ABmed avseende på inköpspris med volymrabatt samt transportkostnad. Utöver dettatillkommer en kvalitativ undersökning om vilka andra kriterier som ärbetydelsefulla vid leverantörsavtal. De viktigaste kriterier applicerades i enegenutvecklad leverantörsvalsmodell som bygger på ramverket ?total cost of ownership?(TCO) där leverantörskriterierna kvantifieras. Utifrån kriterieanalysenframgick att de tre viktigare leverantörskriterierna för Spinactor AB idagsläget är leveransprecision, kundservice och kommunikation samt ekonomiskstabilitet.Lösningen av optimeringsproblemet genomfördes med två olika metoder,linjärprogrammering samt heltalsprogrammering, där linjärprogrammering vardominerande i lösningstid.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

This report shows methods and workflow when exploring the potential to change Outotecs HCD Silver Electrolysis machine to a module type. It?s done as an attempt to lower the workshop and installation costs and to give customer a more accurate prize directly. To do this a concept was produced which was set to a stress test. Additional objectives were to investigate freight and installation procedures, pneumatic connections and to calculate the difference in cost.Once the concept, a reinforced type of the original frame, was chosen stress tests in computer simulations were made and appropriate alterations were made.

The purpose of this study is from a case study develop a model that aims to cost effectively improve productivity in a manufacturing production process. The study highlights the importance of having knowledge about customer needs and using a holistic process perspective when improving productivity to identify the relations between the process stations and by this find problems that cause waste and losses in productivity. Tools and methods used to make production more efficient such as single minute exchange of die, spaghetti diagram, 5s and master production schedule is presented an applied in the model to see how these effect costs, productivity etc.Maintenance effects on quality and productivity in a manufacturing company will as well be covered in this thesis. The results and conclusions finally reveals how the process improvement tools, maintenance and production planning for example effects each other and why it is important to establish an attitude in the company where continuous process improvement should be emphasized..

The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.