De två byggvarugrossisterna Bengtsson & Gedelius AB och Timber Trading AB ska i januari 2006 bilda Elof Hansson Bygg-Gross AB. I samband med sammanslagningen skall även affärssystemen sammanfogas. Syftet med examensarbetet är att, med tonvikt på informationsflöden, undersöka, beskriva och jämföra träpaketshanteringen på Bengtsson & Gedelius AB och Timber Trading AB. Undersökningen har resulterat i förbättringsförslag som kan vara till hjälp vid sammanslagningen av de två företagen. Jämförelsen av teori och nuläge resulterade i ett idealfall vilket i sin tur synliggjorde förändringsbehoven.

In Sweden, the demand for bio energy has increased in recent years due to the current energy and climate debate. In 2008, the energy supply of Sweden was 612 TWh, biofuels accounted for 123 TWh of these. Stumps have been highlighted as a potential fuel in recent years and the Swedish Forest Agency expects a technically and biologically feasible potential of 20.7 TWh annually between 2010 and 2019. The idea of utilize stumps is not new. During the 19th century stumps were used for tar production and during the 70?s and 80?s attempts were made to use stumps in the pulp industry.

Modern sawmills are using the raw-material and the production-capacity more efficiently today, due to rising raw-material prices and higher production costs. Log sweepness has a negative effect on the sawn yield, for sawmills with straight-sawing. It is desirable that these logs could be sorted based on more criteria, if it increases value-yield and consequently the utilization of raw-material. Bow-heights over 1 cm have a negative effect on sawn yield, since the surface of the mantle cuts down in the sawn pattern. Some of these small bow-heights reduce the logs yield of value which affects the production planning negatively. Nearly half of all the Swedish logs have a bow-height over 1 cm.

The annual demands for forest fuels increases in Sweden. At present, large unutilized biomass resources is found in young, dense forests from which about five million oven-dry tonnes (ODt) (23 TWh) could annually be extracted as forest fuel. But harvesting small trees give high logging costs and new cost-efficient harvesting techniques are therefore required. The aim was to study the productivity of Vimek 608 BioCombi in forest fuel thinning of Lodgepole pine and to calculate the economy of the harvesting and estimate the thinning quality. The time study was performed in Åmarken in the county of Västerbotten.

One of the most important components of a harvester is the crane. Most harvester cranes are only possible to pivot (or horizontally rotate) at the crane pillar. Cranab in Vindeln, Sweden, has developed a new type of harvester crane which has an extra pivot point on the outer boom. This makes it possible to reach around residual trees, easing thinning work in dense stands. The aim of the study was to analyze if the use of a pivoting outer boom (POB) crane gave an increase in thinning production and if there were any differences in time consumption between the work elements for the POB crane and a conventional crane. A Valmet 911.3 equipped with a POB crane was used in the study.

Vår studie bygger på artiklarna ?Fads, Martingales and Market efficiency? och ?Volume and Autocovariances in Short-Horizon Individual Security Returns? och är ett replikat av dessa.Studiens syfte är att undersöka förhållandet mellan förändringar i aktieomsättningen och veckoavkastningar för enskilda aktier på Stockholmsbörsen..

The efficiency of the harvesters work is more often reviewed, than the work of the forwarders. In a local Stora Enso office the differences between the harvesters reported volume of timber, and the actual volume delivered to the industry had been noticed. Therefore, the decision was made to do a review on the forwarders work. The review was conducted together with a worker from Vmf Qbera, who is working daily with wood measurement, in order to get a valid evaluation of the logs. Eight sites were included in the survey, and on each site 50 logs were marked. Approximately one third of the marked logs were pulpwood, and the remaining logs marked were timber.

Today green tree retention, together with leaving dead wood, is a common practice with the aim to reduce negative impacts on biodiversity and environment due to clear-felling. To better understand whether this conservation practice also makes a long-term difference, it is important to know what happens to these trees after harvest. Few studies have made an assessment of what happens to retention trees over a longer time period. In this study I inventoried retention trees that were left at clear-cuts six, twelve and eighteen years ago. I carried out a re-inventory of 57 retention patches (divided into free-standing tree groups, small swamp forests and edge zones) and free standing dead trees, spread over 25 previous clear-cuts in central Sweden.

Prosthetic leg can give a negative psychological effect to the user, which ends up in decreased self-esteem and that the user hides his handicap. xCover gives a more natural volume and a cool look. xCover changes the look of the prosthetic leg C-leg. The product is constructed by us, Patrik Svensson and Magnus Zetterqvist, for Christoffer Lindhe at Lindhextend AB. Christoffer has hired Martin Bergman at Smedjan 17 to make the design.

AbstractEmbla 5 is an office building which has done a large improvement. The clients of this building has made an order of WSP and the student Anders Kempe to calculate the use of energy for the building, and after that result proposing further measures which can decrease the energy use of Embla 5.The ground for this report is when calculation of the present energy use of the building is stated. To make that information of a number of parameters such as envelope, the heating system and ventilation has been located and set in to the simulation program IDA ICE which calculate the energy use.To improve the energy use further this project has been concentrated to change the system of ventilation. Today the ventilation system is of the kind CAV (constant air volume) and the air flow is dimensioned for after recommendations from BBR and Arbetsmiljöverket in the office spaces. Consider that Embla 5  is an office building where the people only staying for 8-10 hours/day so was the ide to see how much energy saving if the air flow is reduced the time people not being in the building.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

Prosthetic leg can give a negative psychological effect to the user, which ends up in decreased self-esteem and that the user hides his handicap. xCover gives a more natural volume and a cool look. xCover changes the look of the prosthetic leg C-leg. The product is constructed by us, Patrik Svensson and Magnus Zetterqvist, for Christoffer Lindhe at Lindhextend AB. Christoffer has hired Martin Bergman at Smedjan 17 to make the design.

In this study, we examine the presence and consequences of CEO overconfidence in the Swedish market. We identify overconfidence with two insider-trading based measures and find that overconfidence is apparent among one third of CEOs in companies listed on the Swedish stock market. We also find that these CEOs are more prone to carry out acquisitions, as the probability of conducting an acquisition increases by 27 % if the CEO is overconfident. However, we do not find evidence that acquisitions by overconfident CEOs are more value-destroying. This finding contradicts results from previous studies conducted on Anglo-Saxon markets that suggest that overconfidence has a negative impact on the value-creation in acquisitions.

Introduction: Urinary retention is a common postoperative complication associated with bladder distension. Permanent damage to the bladder affects the patient?s quality of life and may lead to a lifelong inability to empty the bladder and needs of self-catheterization with the risk of urinary tract infection. Bladder distension was classified as the fourth largest health care related injury in Sweden in 2013. Bladder distension may occur before the operation starts and is more common among orthopedic patients.