Scandinavian Biogas is involved in the planning of a combined ethanol and biogas factory in Karlskoga, Sweden. Besides biogas and ethanol large amounts of digester residues will be produced, about 450 000 liquid tonnes residue (~7,3 % Dry Substance( DS)). The objective of this thesis was to investigate possible uses of the residue from the biogas production process ScandgasEthanol developed by Scandinavian Biogas, and to derive a methodological approach how to evaluate and compare handling systems. Three systems where proposed and compared in this thesis; spreading of the untreated residue as fertilizer (system 1), dewatering to a higher DS content to reduce transportation before spreading as fertilizer (system 2) and production of a solid fuel by dewatering and drying the residue (system 3). The general conditions for the proposed systems were investigated in terms of practical viability, economical aspects, environmental impact and energy inputs/outputs.

This thesis examines Swedish composers' modes of work and production within the Swedish film industry. It starts off with a historical overview treating live music in early silent film, the conversion to sound and the Swedish production climate until present time. The analysis consists of contemporary empirical studies; interviews with people writing music for film, TV and commercials. The musician's perspective is in focus but directors and other film workers are heard as well. The situation for female composers in a male-dominated industry is also discussed.

Automatic milking systems (AMS) are part of a growing trend in Sweden and the number of milk-producing farms is decreasing rapidly. One main reason for the AMS is its ability to facilitate work for the farmer. The effects of introduction prior to calving have not been documented earlier and farmers are not in agreement, however they seldom see a problem with the introduction. The aim of this report is to find differences between two groups of heifers, where one group is trained i.e. introduced to the AMS before calving and the other group is introduced after calving.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.

This thesis has been carried out at Diac Metal AB at Torsvik outside of Jönköping. The company produces parts for, amongst others, office furniture and store equipment. The essay will be concentrated on one detail which is included in many of their products.Today the company uses an ordering quantity based on experience which is rarely updated. Furthermore the operations are performed in both the company?s own engineering workshop but also an external workshop.The purpose with the report has been to check whether an updating of today?s batch shaping and ordering system can mean simpler storage control and possibly cost reduction.

Our employer Camatec Industriteknik AB gave us the assignments to increase theirs range of versions on Camcoil that is their own patent product. Camcoil is a capstan system that is used when steel band fabricated. Exist for example in production lines their steel band should be annealed. Our goal with this work is to come up with a completed production basis on a Camcoil for heavy industry. The basis should contain calculations, 3D-constructions, drawings and cost proposal on manufacturing and detail purchase.Demands on this project:1.

Ocean Thermal Energy Conversion, OTEC, a technology using the temperature difference between cold deep seawater and warm surface water, can extract the work in the form of electricity. OTEC gives also synergies of drinkable fresh water. The temperature difference has an impact on the efficiency of the technology, which means that the feasibility of OTEC is geographically limited. The project intends to explore the possibility of replacing the atoll Tarawa?s present electricity generation with an OTEC plant and to explore synergies. In the present situation all of Tarawa?s electricity is generated by fossil fuels.

Akademiska hus is a real estate company that specializes in providing Swedish universities with housing facilities for educational and research purposes. The company strives to reduce its use of energy by 40% between the years 2000 and 2025. The aim of this thesis is to determine which measures can be taken to reduce the need of purchased energy in a building that is used by theSwedishUniversityof Agricultural Sciences inUppsala.In order to determine the results of various changes to the building envelope and ventilation system, the building was modelled in the computer simulation program VIP-Energy. Other proposed changes to make the use of energy more efficient concerned water use and lighting. The need of purchased energy can also be reduced by producing electricity or heat on site, using solar energy.Results show that economically viable measures include upgrading windows and faucets, adjusting control systems for ventilation and lighting, and installing roof mounted solar panels for power production.

Ocean Thermal Energy Conversion, OTEC, a technology using the temperature difference between cold deep seawater and warm surface water, can extract the work in the form of electricity. OTEC gives also synergies of drinkable fresh water. The temperature difference has an impact on the efficiency of the technology, which means that the feasibility of OTEC is geographically limited. The project intends to explore the possibility of replacing the atoll Tarawa?s present electricity generation with an OTEC plant and to explore synergies. In the present situation all of Tarawa?s electricity is generated by fossil fuels.

Biogas is a renewable fuel that can be extracted from anaerobic digestion of many differentsubstrates, for example biological household waste. An alternative handling of the waste is tomix it with other wastes and incinerate it in a combined heat and power (CHP) plant. Thisstudy uses life cycle assessment to investigate which type of waste handling that is betterfrom an environmental point of view, anaerobic digestion with biogas production orincineration. The results are based on a case study of a biogas production plant owned by thecompany Ragn-Sells in Vänersborg. The alternative is incineration at a CHP plant inGothenburg.

The cost of construction projects have increased during the past few years. Different actors in the construction industry work together to advocate various measures to mitigate these cost increases. One of these measures is to try to improve the efficiency in the phase of production. By striving for a kind of standardization with a constant quest for improvement, the productivity can increase while the costs of production fall.For this thesis has a case study been conducted at the construction company JM AB which is seeking this. They call the approach structured production and have implemented various measures to achieve a more productive output.Based on information from reconciliations, the cost and the spent hours of craftsmen have been analyzed at the company where the case study took place.

I dagens samhälle ställs hårda krav på resultatförbättringar i företag och industrier. Det är vanligt att företag tar hjälp av någon eller några av de ledningsverktyg som finns utvecklade i just detta syfte, Lean Production är ett av dessa verktyg. Syftet med denna rapport är att ge en historisk bakgrund till Lean Production och att undersöka vilka tillvägagångssätt tre företag har valt för att implementera Lean i sin verksamhet. Vidare skall författarna undersöka om det finns några likheter mellan dessa tillvägagångssätt och Toyotas produktionssystem (TPS).Utvecklingen till det som idag benämns som Lean började redan 1911 då Fredrick Winslow Taylor presenterade sin artikel ?Principles of Scientific Management?.

This thesis examines Swedish filmmakers' modes of work and production within the Swedish film landscape. An introductory historical overview treats the Swedish regionalization since the mid 1990's. Political and economical aspects of producing films in various regions serve as a background for understanding the new generation of decentralised Swedish filmmaking, and the use of sound and music in contemporary film. The analysis consists of empirical studies; interviews with directors and producers, working with music for film and TV. Although the filmmaking perspective is in focus, composers and film scholars are heard as well.

This diploma work covers an investigation over the heat - and hot water systems of thetenant-owner's association, Bogården. The heat - and hot water needs of Bogården aresatisfied by both district heating as well as three heat pumps. Implemented investigationshows that the heat pumps are not used in a profitable way. Apart from that, the reservepossibilities are small. There is also a risk of the growth of Legionella bacterium in thehot water system.Since the heat pumps are already installed, HSB-Gävleborg (responsible for Bogården)has a wish to investigate possible proposed actions for optimization of existing plant.After completed investigation, a new proposed action is presented.

Several technical solutions are ready to step forward as the new generation of propellant, and this report aims to explore the possibility of commercializing fuel cell cars. The report is based on current research and data from today's technology and engineering solutions that are estimated to be commercially realized before 2020.A mapping of today?s different fuel cell options has shown that the most suitable fuel cell option is the Proton Exchange Membrane Fuel Cell, which uses hydrogen as fuel. The report is focusing on a techno-economic well-to-wheel analysis of hydrogen and the energy balance and costs in a system perspective. The basis for this analysis consists of two centralized methods of production, steam methane reforming (SMR), and alkaline water electrolysis.