Mechanical ventilation is the most common type ofventilation in newly constructed office buildings. Therehas been an interest to utilize natural ventilationinstead of mechanical ventilation among architects andHVAC consultants in recent years. This is due to thesize of mechanical ventilation systems, which arespace consuming. The mechanical ventilation system isalso complex and requires maintenance. Furthermore,the fan uses a considerable amount of energy.

Marine heatwaves (MHW) have become increasingly common in recent decades due to greenhouse gas emissions that have caused climate change. A marine heatwave is when the sea surface temperature rises, which damage many different ecosystems in the sea. One ecosystem that is sensitive to temperature changes is tropical coral reefs, which are at risk of bleaching during marine heatwaves. Coral bleaching is when its symbionts leave the coral and they lose their color, while also starving to death as they lose their food source. The purpose of this report was therefore to investigate what the connection between marine heatwaves and coral bleaching looks like, and to see if there are any geographical differences.

Transdermal drug delivery, besides painfulinjections with syringes, has long been associatedwith small size particle pharmaceuticals, which candiffuse through the skin. This method of drugadministration has only been applicable on a smallnumber of drugs, where active molecules are smalland delivery time should or can be long.Other drug delivery options are oral administrationand injection with hypodermic needles (ordinaryhospital syringes). In oral administration thestomach and liver tend to dissolve the drug and theeffect becomes more difficult to anticipate, anddrug delivery rates difficult to control. Hypodermicneedles are used as a mean of drug injectiondirectly into the bloodstream. This method ispainful and risks infection due to tissue damageand skin penetration.One way to get a painless non-damaging techniquewith high delivery rate that still can delivery largemolecules is to manufacture an array of microscopichollow needles and equip them with a pumping unitthat delivers the correct amount of drugs.This thesis shows the technique and possibility ofmanufacture micromachined needles using low costtechniques of Ion Track Technology (radiation ofheavy ions creates porous materials), electrolessdeposition (non-current activated wet chemistrymethod of depositing metal) and electroplating.

The purpose of this report is to find out which crops, that are good for strawfuel, and can be grown i the area around the city of Lund. The background of this report it that Lunds energy is planning to bild a biofuelheated Thermal power station in Örtofta outside of Lund. I have in the report limited me to the crops hemp, whole crop (triticale), reed canary grass, elephant grass and jerusalem artichoke. I have through a documentary research checked the crops, cultivabillity in the south of Sweden, and how they should fit, in the Scanian crop sequence. Hemp is an annual crop which probably could manage in the Scanian crop sequence. Whole crop often triticale because of it´s high yield and low rate of shed seed. Could also fit into the crop sequence of crop in Scanian. Triticale is annual, and could be grown at the same kind of fields as used to wheat, whith is why it would be possible to grow it in Scania. Reed canary grass is a reedlike grass that is easy grown at most soils.

Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a Thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

 This degree project aims at developing a concept for how to use solar energy to pump up water. The target audience is people living in areas where the functioning of the electricity and water network is absent. In these areas, the hand-powered water pump is the most common technology. The degree project's goal is to find an economically viable alternative to the time consuming hand-powered water pumps. The power comes from solar energy.

This report covers a product development project conducted as Bachelor of Science thesis forthe Innovation & design engineer program at Karlstad University.The assignment was supplied by MMB Consulting, Kristinehamn. The purpose of this projectwas to find an alternative way of shaping wire-net insulation mats. This insulation product isused for fire and Thermal insulation of technical installations. The insulation consists of stoneor glass wool with a sewn on steel wire netting on the out facing side. This netting has thepurpose to enable fastening to e.g.

This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW Thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Idag står bostads- och servicesektorn för närmare 40 % av Sveriges totala slutliga energianvändning. Flerbostadshus utgör ca 30 % av den energianvändningen. Därför är det viktigt att lokalisera energiparametrar och redovisa dess betydelse för energianvändningen. Samtidigt bör relationen mellan energianvändning och inomhusklimat analyseras, så att inte förändringar i energin medför till försämringar för inomhusklimatet. Baserat på identifiering hos energisparpotentialen hos parametrar, parameterbeteende och parameterkänslighet för energianvändning har i studien ett antal parametrar undersökts för ett flerbostadshus.

With higher prices for oil and increased focus on fossil fuels impact on the environment the heating sector are searching for alternative fuels. Pellets are a quite new product whose production has risen exponential in recent years. Today there are small-, medium-and large-scale users, where the large-scale consumers are the heating sector. The heating sector is mainly using oil to cover the increased demand during cold periods. The purpose of this study is to analyze the potential of pellets if it would replace Thermal power plants oil and coal. The study will also analyze the economic impact a conversion would mean for a heating plant and if the pellet is a reasonable substitute. 2008 statistics from the Swedish district heating association were analyzed and a calculation was performed to determine how many tons of pellets is needed to replace coal and oil.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.