Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

The purpose of the project is to determine the impact of solar cells and electrical vehicles on the future electricity grid and distribution network. Future electricity grids will be affected differently than it does today. Therefore, it is important to determine the impacts so that the current electricity distribution system can be developed and redesign to achieve the future demand. In Sweden, government has changed rules and laws in order to make it easier for private sector to invest in renewable energy sources. Our project focused on the impact of the solar cells and electric vehicles on the low voltage electricity distribution.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

Background: Sweden is a country where vitamin D deficiency seems to be common, partly because of its geographical position, which reduces the availability of UVB radiation, but also that people avoid sunlight due to increased skin cancer risk. Research shows that vitamin D plays an important role in the prevention of many diseases such as cancer as well as autoimmune and neuropsychiatric diseases.Vitamin D is a fat soluble pre-hormone and a collective name for closely related compounds which act as hormones after undergoing a transformation in the body.Humans can utilize vitamin D through diet and produce it in the body by exposing the skin to the sun. Previous observational studies and epidemiological studies have established a hypothesis that there seems to be an association between vitamin D supplementation and reduction of depressive symptoms.Objective: The aim of this study was to investigate if vitamin D supplements may decrease depressive symptoms.Methods: This work is organized as a literature review and article search is made in the database PubMed in January 2012. Keywords used were ?vitamin D and depression? and inclusion criteria were: randomized clinical trials, be conducted on humans, written in English.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

 This degree project aims at developing a concept for how to use solar energy to pump up water. The target audience is people living in areas where the functioning of the electricity and water network is absent. In these areas, the hand-powered water pump is the most common technology. The degree project's goal is to find an economically viable alternative to the time consuming hand-powered water pumps. The power comes from solar energy.

Denna rapport kommer av avhandla det examensarbete som genomförts inom civilingenjörsprogrammet innovation och produktdesign på Mälardalens högskola. Arbetet har genomförts på RemaControl Sweden AB och startade den 3:e september 2012 med slutpresentation den 29:e mars 2013.RemaControl är ett företag som är baserat i Västerås och tillverkar mätsystem till sågverksindustrin. Den produkt som detta projekt har kretsat runt är deras mätsystem som heter RemaLog X-Ray som är ett ?state-of-the-art-system? som använder sig av röntgen för att läsa av mätdata från trästockar när de kommer in på sågverket.Uppdraget från RemaControl var att omkonstruera den skyddshuv som omsluter röntgenrören. Dess syfte är att skydda miljön utanför mätramen från strålning som röntgenrören genererar.

This report covers a product development project conducted as Bachelor of Science thesis forthe Innovation & design engineer program at Karlstad University.The assignment was supplied by MMB Consulting, Kristinehamn. The purpose of this projectwas to find an alternative way of shaping wire-net insulation mats. This insulation product isused for fire and thermal insulation of technical installations. The insulation consists of stoneor glass wool with a sewn on steel wire netting on the out facing side. This netting has thepurpose to enable fastening to e.g.

This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Idag står bostads- och servicesektorn för närmare 40 % av Sveriges totala slutliga energianvändning. Flerbostadshus utgör ca 30 % av den energianvändningen. Därför är det viktigt att lokalisera energiparametrar och redovisa dess betydelse för energianvändningen. Samtidigt bör relationen mellan energianvändning och inomhusklimat analyseras, så att inte förändringar i energin medför till försämringar för inomhusklimatet. Baserat på identifiering hos energisparpotentialen hos parametrar, parameterbeteende och parameterkänslighet för energianvändning har i studien ett antal parametrar undersökts för ett flerbostadshus.

With higher prices for oil and increased focus on fossil fuels impact on the environment the heating sector are searching for alternative fuels. Pellets are a quite new product whose production has risen exponential in recent years. Today there are small-, medium-and large-scale users, where the large-scale consumers are the heating sector. The heating sector is mainly using oil to cover the increased demand during cold periods. The purpose of this study is to analyze the potential of pellets if it would replace thermal power plants oil and coal. The study will also analyze the economic impact a conversion would mean for a heating plant and if the pellet is a reasonable substitute. 2008 statistics from the Swedish district heating association were analyzed and a calculation was performed to determine how many tons of pellets is needed to replace coal and oil.