Climate and environmental issues is now high on the agenda. We live in a generation that must try to solve some major environmental problems. Buildings and habitations account for approximately 40 % of Sweden's total energy today. To reduce this figure, as needed, more research in the field of energy efficiency is required.This thesis concerns the heating of buildings. The load on district heating is heavy during certain times of the day.

Climate and environmental issues is now high on the agenda. We live in a generation that must try to solve some major environmental problems. Buildings and habitations account for approximately 40 % of Sweden's total energy today. To reduce this figure, as needed, more research in the field of energy efficiency is required.This thesis concerns the heating of buildings. The load on district heating is heavy during certain times of the day.

A problem in the field of district heating is the oil burners needed to provide power when a peak load occurs. One possible way of reducing the needed amount of oil is to reduce the power demand for space heating in the district-heating substations when the need for district heating water exceeds a certain limit. This can be done by use of a locally working controller function.In this Thesis the options concerning load priority are evaluated. To evaluate the potential for using controller functions concerning peak load priority an experiment was brought out in a chosen district-heating substation. The impact on the indoor thermal comfort during a heat reduction was also taken into account.

The research work performed in this thesis has been carried out at the Production Tech-nology Centre where the Thermal Spray research group of University West has its work-shop and labs.This research work has been performed in collaboration with the International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI), Hyderabad, India.First of all, I would like to express my sincere thanks and gratitude to my supervisors Dr. Nicolaie Markocsan and Dr. Nicholas Curry for their guidance, great support and valuable suggestions without which this work could not have been possible. I would also like to thanks Prof. Per Nylén for keeping faith in me and providing me an opportunity to work at PTC, which is a great place to perform research.

This thesis has been carried out on behalf of IV Produkt AB and intends to set an average ratio of thermal energy losses in apartment buildings that were built during the 1960-1990. This shall be derived by analyzing the total district energy consumption that has been divided into three parts: heat energy losses (the actual heating requirements), the heating of domestic hot water and heating energy consumption for the controlled ventilation.Three different residential areas that were built during the years 1962-1966 and one that was built in 1993 has been analyzed. All residential areas are located in Växjö urban and contains between four and six apartment buildings.The analyzed objects have a mechanical exhaust ventilation systems and district heating as the heating method. No own laboratory work or experiments have been done in this thesis, the calculations have been done on the basis of parameters from VEAB, interviews with property managers, and literature studies. By calculations, we have got a result that is reported in Chapter 6.

WSP building physics in Stockholm has certified the preschool Temmelburken in Bromma with the system of certification Miljöbyggnad. The rating of the building became BRONZE. In this thesis the preschool has been investigated with respect to the three areas: thermal climate, use of energy and improving of the level of certification. The thermal climate at the preschool has been investigated by a questionnaire survey and by measurements in order to do comparisons between the results from the two investigations as well as with the results of the simulations that WSP has done at the certification of the preschool. The differences between the results from the simulations and the questionnaire survey for winter as well as from the measurement performed with a comfort meter the 19th of March are concidered to be reasonably small since they give rise to the same rating according to Miljöbyggnad.   Operational data for the use of energy for the preschool have been obtained in order to do comparisons with simulations performed by WSP and Svenska Besiktningar AB. The comparison shows that the simulated values for the specific use of energy are lower than what the real specific use of energy would be for the preschool, since just the operational data for the heat energy is higher than the simulated values. At the investigation of the possibility of improving the level of certification it was found that the rating of the preschool can be raised from BRONZE to SILVER by improving the ratings of the ?thermal climate summer? and the ?daylight?.

Högpresterande isolering är en typ av material som finns tillgängligt men inte används på den svenska marknaden i den utsträckning som de bör göra. I denna rapport kommer det högpresterande isoleringsmaterialet PIR att ligga i fokus och det jämförs främst med det traditionella isoleringsmaterialet cellplast men paralleller dras även till mineralullen.PIR- isoleringen har 40 % bättre värmekonduktivitet än cellplasten och detta innebär att materialet har bättre isoleringsförmåga som bidrar till tunnare konstruktioner. Isoleringen är därför idealiskt att använda för passiv-, lågenergi och nollenergihus. En annan egenskap som utmärker PIR- isoleringen är dess brandegenskaper som uppfyller en högre brandklass än cellplasten, trots att det är ett plastmaterial.PIR- isoleringen är ett dyrare material, dock sparas pengar in redan vid produktion då fukt- och vindskydd kan uteslutas i en konstruktion. Om högre energikrav ska uppfyllas kan pengar även sparas in på sikt genom lägre energikostnader..

Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest production cost. The production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

In the last few years people have become more and more aware of how humanity is affecting the climate. In the direction of reducing the greenhouse gases is to design engines with higher tensile properties and reduced weight, in order to achieve lower fuel consumption and cleaner fuel incineration in today's truck engines.In order to achieve these requirements it?s necessary to increase the combustion pressure in the engine. This requires higher tensile properties and high thermal conductivity of the engine material. The department of Component Technology at the University of Jönköping in collaboration with Volvo Powertrain AB, Scania CV AB and DAROS Piston Rings AB has been commissioned to develop this material and to find knowledge of material properties used in truck engines and piston rings used for marine applications.The purpose with this work is to analyze the tensile properties of a series of cast iron, cast under different metallurgical conditions.Four different series of cast irons have been analyzed from four points of view, carbon concentration, nodularity, amount inoculation and cooling rate.After the tensile test all specimen data was analyzed in a mathematic calculation program called Matlab 2006a.

In today?s society climate change has grown to one of the largest global issues. To reduce emissions of greenhouse gases, large changes of the energy system are required. An increasingly popular solution is investments in local production of renewable energy resources like wind, solar or geothermal power. The following report examines the possibility for implementing a solar power plant on the new hospital Nya Karolinska Solna. Two different technologies for extraction of solar energy has been studied, solar thermal collectors  to meet the need of heating and solar cells to satisfy the need for electricity linked to operating the hospital building.

When a combined heat and power plant produces heat and power it often faces a deficit of heat load during the summer or other periods of time. This heat is often unnecessarily cooled away or the power production has to be reduced or shut off. If it is possible to store heat from periods with low heat demand to periods with high heat demand one can get many benefits. Among these benefits are: increased power production, decreased operation with partial load, uniformly distributed load.To be able to store heat in situations like this long-term thermal heat storages are needed. In this thesis five different types of stores are presented: rock cavern storage, tank storage, pit water storage, borehole storage and aquifer storage.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Konservatorprogrammet15 hpInstitutionen för kulturvårdGöteborgs universitet2012:22.

Students? performance in school is dependent on the indoor climate. This report studies four schools regarding air quality and thermal environment. A survey was made at the schools as well as measurements of carbon dioxide, dampness, thermal climate and, as an indicator for the furniture?s capability to collect dust, shelf factor and fleece factor.

This report is the written documentation of a project work carried out at the Division of Engineering Materials at Luleå University of Technology in cooperation with Seco Tools AB. The project deals with the analysis of residual stresses in Ti-Al-N thin film grown on WC/Co cutting inserts. The composition of Al varied from 0% up to 75%. Increasing the Al content in the Ti(1-x)Alx N compound improves the compressive residual stresses even after annealing of the material. The experiments have been performed in a high temperature x-ray diffractometer (HTXRD) where the interplanar atomic spacing was determined in-situ and subsequent converted into stresses.

The purpose of the study is to investigate the possible effects of an unstable ventilation system and its influence on energy use and thermal comfort. The report also explores how qualified personal working with HVAC view and handles system control.In order to meet the requirements in energy efficiency and a comfortable indoor climate control regulation is a prerequisite. With optimized increased complexity of the climate systems, it becomes more challenging to control the system and the risk of unstable control increases. No previous studies about what affect an unstable system can have on energy use and thermal comfort have been found.The report is based on several tests were the controlling variable has been increased until the system becomes unstable. Two different types of unstable systems have been investigated.