This paper goes through solar energy and what uses it has. It is also a guide in the choice of solar collectors forthe real estate that I have drawn for the thesis work.Solar energy is a renewable source of energy from the Sun's light. Energy can be used to produce both heat andelectricity through solar collectors and solar cells. Some of the benefits of solar energy is that it is completely freeto extract, environmentally friendly and virtually maintenance-free. Disadvantages are that the technology isexpensive, does not cover the entire energy needs and takes a long time until it pays.

Jämtkraft AB has recently modernized its hydropower station at Hissmofors by replacing four older worn out units with two new units. The generators uses a concept with sliding stator feet to deal with the thermal movements that occur in the stator during operation when the unit is operating intermittently. At other sites, this method revealed shortcomings in the reliability. This has made Jämtkraft AB feel uncertainty about its function and therefore want to investigate it during an early stage. The generators have a built-in monitoring system for the sliding stator feet and by using data from there the function of the sliding stator feet has been investigated. The study focused on how the different stator feet move relative to each other and how the eccentricity and deviation from roundness changed during operation. The results show that there are several indications that the function of the sliding stator feet is not satisfactory.

This is a paper about the effects from smoldering fire on lithic objects from an archaeological view. The introduction gives the background to this paper, a short orientation to forest wildfires and why the work is limited to: flint, quartz, quartzite and slate. Material and methods describes the stone materials and the setup that was used in the temperature logged tests with three replications for each type of material. The fuel in the burnings was peat on a bottom of sand. Flint showed a more drastic effect from heat compared with the other materials. Slate seems to have greater tendencies to change to darker colour and luster at lower temperatures than the other materials.

Swedish farmers have the possibility to be subsidized by EU rural development programme for grazing animals on pastures to promote the biodiversity of flora and fauna. The environmental remedy sometimes does not allow supplementary feed and at the same time the Swedish Animal Welfare Act and the Swedish Agricultural Board?s regulations for animal welfare and protection states that animals, in this case horses, shall be fed with food of good quality and adapted for the species. The regulations also state that they should have an individual feeding regime that enables them to maintain a normal body condition. The aim with this master thesis has been to investigate if it is possible to keep Gotland ponies on extensive pastures, during late spring and summer and still maintain animal welfare. The horses were assessed every fourth week using a welfare assessment protocol developed in line with the Welfare Quality® project (submitted, Viksten et al) where physical, behavioural and resourcebased parameters were observed. Twelve one-year old stallions of the breed Gotland ponies purchased from different breeders were used in the study.

This diploma work on D-level is made in cooperation with Varnäsföretagen AB in Eskilstuna. The company performs contract manufactured aluminium goods. This work is a continuation on earlier diploma work in Varnäsföretagen AB. Even if the industry process consumes much energy for melting the aluminium goods, they consume a great amount of oil to warm up the building. The purpose of this work is to examine some places in the building and the process to see how much energy it is possible to recycles to the heating system and reduce the costs for heating.

The purpose of this study is to investigate how the process and result of renovations in socioeconomic vulnerable areas affect the residents' right to housing; with a focus on women's experiences of their homes, their area, the housing company's apartment renovations. The study is conducted through two research questions: How do the women in L?vg?rdet experience their homes and the area? And how do the women in L?vg?rdet experience the process and the result of the renovations of the rental apartments? The methodology used is qualitative research interviews. The empirical material was gathered through qualitative interviews. Eight women living in L?vg?rdet have been interviewed.

The thesis was performed at Forsmarks Kraftgrupp AB in the department ofmechanical engineering, FTCM. Forsmark nuclear power plant has had problems with cracks in some of the controlrods which are placed in the reactor at Forsmark 3. To investigate the cause of this,material samples were taken from five of the damaged control rods. This sampling ofthe rods resulted too short rods to be transported in the shipping container to theinterim storage facility for used nuclear fuel in Oskarshamn. Control rods are crucial components in a nuclear reactor, regulating the reactoreffect by blocking or unblocking fuel rods. Control rods which have been in thereactor are always handled under water in order to protect against the radiation theyemit. The task was to design a control rod adapter that extends the control rod sotransport can be performed from Forsmark. The goal of the work was a complete setof blueprints so the control rod adapter can be manufactured and mounted on theshort control rods and then be transported to the interim storage facility. The work began with mapping of how control rods normally being handled from thereactor to the interim storage facility.

The goal with this examination thesis is to investigate the difference in carbon dioxide emissions between a building with a wooden versus concrete carcassing from a life cycle perspective. The huge amounts of carbon dioxide released into air from human activities must be reduced to prevent serious consequences. A way to limit this issue is through performing a comparative study where the result shows which of two products with the same function has the lowest emission of carbon dioxide, whereof the product with the lowest carbon dioxide pollution can be chosen.To be able to perform a study like this an object has been chosen and studies about life cycle analyses have been done. The rental square meter, the thermal conductivity value, the energy requirements and the placement of the building has been set equal in both framework types. There were solely dissimilarities of the two buildings taken into account when this comparison study was performed.The result of the study is that a building constructed with a wooden carcassing has the lowest amount of carbon dioxide emissions.

SUMMARY Several studies have shown that weaning pigs are in great need of heat. The reason for this is mainly because the pigs are given very little feed just after weaning. Some of the pig producers of today have tried to get along with these problems by building some kind of hut for the pigs. Some of these pig houses have been included in this study.The study has shown shortcoming functions for the pig cottage. The expected heat increase has not occurred.

A study of paleomagnetic remanence and anisotropy of magnetic susceptibility (AMS) has been performed on the Öje-Diabase in Dalarna, Sweden, and on basic dikes associated with the alkaliquartzsyenite/granite Noran-pluton in central Sweden. Based on isolation of directions of characteristic magnetization in the basic rocks, a division into three different groups (A,B,C) has been made. Group Aconsists of dolerites of Jotnian origin, both dolerites from the Öje-Diabase and dikes associated with the Noran-pluton are included in this group, making them coeval. Group B is suspected to show a re-magnetization from the later part of the Svekonorwegian orogeny. Group C belongs to the Blekinge-Dalarna-Dolerites (BDD). Thermal demagnetization of dolerites revealed two different types of demagnetization behaviours, one where magnetite clearly was the source of the remanence, and an other with a linear decrease in magnetization intensity. The measurements of magnetic anisotropy reveals a magnetic fabric with an almost horizontal foliation and a lineation that indicates a fairly uniform NNW/ S-SE flow direction of the magma..

The goal of this master thesis project was to develop computer models of some plausiblepretreatment techniques and to assess the potential benefits/costs of using pretreatment andanaerobic digestion for waste management of organic waste from a system perspective. Forthis purpose a computer program called ORWARE has been used. ORWARE (organic wasteresearch) is a program for making life cycle assessments of waste management. As the mainpart of the project work the ORWARE system has been provided with three new models ofpretreatment techniques. The additions consist of: One model of pretreatment with ultrasound,one model of thermal hydrolysis and one model of a screw press.

Everyone has to take a greater responsibility in energy issues, both individuals and companies. There have been some major developments in the construction industry but there is still a lot to be done. This diploma work thesis presents different methods of making existing construction shed establishments to use less energy. What is possible to do and how much energy is there to be saved? A shed establishment consisting of 8 shed units were studied in this project and the building simulation tool VIP-Energy was used to simulate different types of material in the sheds. An infrared camera was used to locate thermal bridges. There are several factors that can be improved to make a construction shed establishment to use less energy.

The purpose of this study has been to evaluate whether a Low temperature bio-mass dryer could be integrated with the local district heating system in Malå. The aim is to increase the thermal efficiency of the cogeneration plant in Malå, by lowering the temperature of the cooling medium. Another benefit that comes from this is improved combustion efficiency at the power plant, since drying the fuel causes an Increase of the heating value.Simulations has been made in Excel, and with use of linear regression, to find out if it is profitable. Data for this purpose has been supplied by the power company Skellefteåkraft and furthermore SMHI.The result of the Calculations shows that a very efficient bio-mass dryer is needed, if yield of investments should be made possible. An Investment of 4,27 Mkr, in a dryer, could at a such criterium return 60000 kr/year, if the price of the biomass is 190kr/MWh.

The aim of this project is to examine the needs and problems that exists amongst homeless people and to develop a solution that will help them in their everyday life. Since the homeless are a relatively large vulnerable group i Sweden, their everyday lives could be made easier in many ways.A clear definition of the target group is put together to create a good starting point. What state and help orginazations do to help the homelss and the society?s view of the homeless is also relevant and has been documented. Four personal stories have been put together to desicribe cases of clear problems existing in everyday life.Several interesting problems has been defined from the research and acceptance in the communtiy, desire to be seen and heard and a lack of confidence were the main needs.

Examensarbetet syftar till att hitta samband mellan ytliga sprickor hos virke, i form av dimensioner och karaktärer, som dagens maskinella avsyningssystem inte klarar av. Tyngdpunkten i projektet har legat på att identifiera eventuella samband mellan verkligt djup hos sprickor och de ytliga sprickmått som kan uppmätas med automatisk avsyning av WoodEye. I huvudsak har projektets praktiska undersökningar gått ut på att bestämma sprickors ytliga dimensioner, djup, typ och position med hjälp av automatisk avsyningsutrustning (WoodEye) samt genom manuell uppmätning i ett antal itusågade sprickzoner. Det provmaterial som använts i utförda försök och som legat till grund för efterföljande sprickanalyser har varit av sådan karaktär att det kunnat jämställas med konstruktionsvirke som normalt sett hållfasthetssorteras enligt europasstandard SS-EN 14081-1.I projektet har 568 sprickor, fördelade över 8 olika spricktyper, analyserats. Av erhållna resultat har det konstaterats att störst respektive minst medelbredd uppvisades hos kådlåpor respektive kantsprickor, störst respektive minst medellängd uppvisades hos splintsidesprickor respektive kådlåpor, samt att störst medeldjup uppvisades hos fäll-, kap- och stormsprickor.