This report is the result of a thesis work in Integrated Product Development, regarding hygienic features in dishwashers and especially disinfection by the use of steam.The thesis is performed at Electrolux Primary Development Dishcare in Stockholm and in collaboration with the Department of Machine Design at the Royal Institute of Technology.The targets of the thesis are to prove the advantages of a technology suitable to implement as a hygienic feature inside a dishwasher and to realize a functional prototype of a differentiated hygienic feature that does not exist on the market today.The process followed to perform the thesis is the process defined for Electrolux Primary Development.The technology chosen for development is disinfection by heating the water on the surface of the dishware, by the use of steam.A number of tests on how steam behaves when injected into the dishwasher tub have been performed, providing the results that have been taken in consideration when designing the prototype.The prototype consists of a pipe system provided with nozzles to eject the steam into the upper parts of the dishwasher. Tests of the final prototype show that thermal disinfection of water in a dedicated area of the tub can be reached within 9 minutes. The operation requires 0,17 liters of water and consumes 0.2kWh..

The aim of this project is to examine the needs and problems that exists amongst homeless people and to develop a solution that will help them in their everyday life. Since the homeless are a relatively large vulnerable group i Sweden, their everyday lives could be made easier in many ways.A clear definition of the target group is put together to create a good starting point. What state and help orginazations do to help the homelss and the society?s view of the homeless is also relevant and has been documented. Four personal stories have been put together to desicribe cases of clear problems existing in everyday life.Several interesting problems has been defined from the research and acceptance in the communtiy, desire to be seen and heard and a lack of confidence were the main needs.

The dry out criterion (MCPR) has been calculated for the most limiting H2-events for Forsmarks unit 2 and 3, at operating points that are normally not analyzed before each cycle. The operating points that normally are regarded as the ones with the lowest margin to dry out are the ones where the thermal power is the highest at agiven recirculation flow. This report shows that this is not the case for Forsmark 3. MCPR-values at partial power operating points are higher for the limiting case inside rather than on the boundary of the region of operation. It is therefore recommended that the method for determining the dry out criterion for Forsmark 3 is revised to account for this effect.

År 1987 trädde en ny byggnadslag i kraft, Plan- och bygglagen(PBL). I och med den nya lagen minskade kommunens och byggnadsnämndens kontroll av projekteringshandlingar och besiktningar ute på arbetsplatsen. Efter lagändringen beror den slutgiltiga kvaliteten på en byggnad i större utsträckning på byggherrens och entreprenörernas egenkontroll. P.g.a. olika intressekonflikter inom kommunen, och att det kan förekomma starka kopplingar mellan byggherre och entreprenör, är det inte alltid självklart att kommunens tillsyn vid nybyggnation gällande till exempel egenskapskrav på energihushållning och värmeisolering utförs tillfredsställande.Med ovanstående i åtanke undersökte vi fyra flerbostadshus, två i Värnamo kommun samt två i Kristianstad.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

This paper aims to, through a literature review, examine how to best design and adapt calf huts to meet the calf's physiological requirements and reduce the infection pressure for enteric and respiratory diseases. It illuminates how the calf relates to different temperatures and climate, which temperature control mechanisms it uses and its ability to perform these regulations, as well as providing a summary of the past decades´ research on the calf huts housing system. These two theory chapters, along with a concluding discussion, provide a better understanding of how to, especially in temperate climates, design the most suitable calf hut, which cater to the calf's both thermal comfort and physical health. The literature suggests that the calf's own temperature control works well to counteract the temperature outside the desired range, and that one of the most important factors rather is ventilation of a calf hut, which reduces moisture and pathogens. The conclusion of this paper is mainly that there is not an obvious way to place and construct a calf hutch and that most design principles contribute to both positive and negative effects simultaneously.

At Forsmarks Kraftgrupp AB (FKA) forces on pipe systems due to transient flow are frequently calculated as a step to verify their structural integrity. In nuclear industries these forces are often calculated with a one dimensional thermal-hydraulic analysis-code called RELAP5. When calculations regarding more complex geometries are needed, the three dimensional code Fluent is often used. This code is highly time consuming and requires large computational power.This projects aim is to compare calculations of pressure, flow and forces carried out by RELAP5 and Fluent for an arbitrary pipe section during transient flow conditions. This has been accomplished by constructing a simple geometry for which a transient flow is simulated in both programs.

The purpose of this thesis was to make an energy survey and quantify energy flows of individual unit operations associated with the biogas production in Uppsala Vatten och Avfall AB:s biogas plant, located at Kungsängens gård. Moreover, large consumers of energy would be identified and analyzed. The objective of this energy survey was to obtain a detailed understanding of the energy use in the biogas production. The energy survey was divided into two parts: electricity and heat. Each part was treated separately and with somewhat different approach. To estimate the electricity usage during the projcet the rated power of each selected unit operation was noted and multplied with the measured time of usage.

The purpose of this thesis was to make an energy survey and quantify energy flows of individual unit operations associated with the biogas production in Uppsala Vatten och Avfall AB:s biogas plant, located at Kungsängens gård. Moreover, large consumers of energy would be identified and analyzed. The objective of this energy survey was to obtain a detailed understanding of the energy use in the biogas production.The energy survey was divided into two parts: electricity and heat. Each part was treated separately and with somewhat different approach. To estimate the electricity usage during the projcet the rated power of each selected unit operation was noted and multplied with thenmeasured time of usage.

The aim of this work is to develop new conceptual designs for the fairings that are situated between the fin and the rear fuselage on the new version of the JAS 39 Gripen aircraft, called the Gripen E/F. The designs presented should show a profit in the form of lower weight. To achieve weight loss, the possibilities of using other construction materials other than those which are available at Saab today were studied. Therefore, a material survey was carried out in which the market for modern construction materials was studied to get an idea of today?s level of technology.

Rapporten innehåller inledningsvis en faktadel med allmän information kring temperatursprickor i betong. Här presenteras bl a uppkomsten av fenomenet, vilka typer av sprickor som förekommer och vad ett tvång är. Tanken är att ge läsaren tillräcklig kunskap för att kunna förstå sig på de övriga delarna i rapporten.Resultatet och det huvudsakliga arbetet redovisas i form av tabeller med tillhörande illustrationer där det går att utläsa vilken sprickrisk som förekommer vid flera specifika fall och vilken åtgärd som bör vidtas för att eliminera sprickrisken. Som konstruktör kan du med din egen indata, dvs. dimensioner och temperaturer, följa tabellen och finna resultatet för ditt specifika fall.

In today?s fast growing and closely connected society, a reliable and energy efficient transportation system is more than ever desirable. Nowadays the significant part of the transportation sector?s energy demand is supplied by fossil fuels.Improving energy efficiency in combustion engines will result in reduction of fuel consumption and CO2 emissions. A modern internal combustion engine has an efficiency of 30-45 %, where the most energy loss occurs as result of heat losses in the exhaust and cooling systems.

Skin temperature is detected through signals in unmyelinated C-fibers and thin myelinated A?-fibers in the peripheral and central nervous system. Disorders in thin nerve fibres are important and not rare but difficult to diagnose by the most common neurophysiological methods. In this pilot study different methods for quantitative sensory testing, QST, were compared to give some ideas about which method could be the most efficient to use in order to point out injuries of the sensory system in clinical practice. The comparison was made between Békésy (separate warmand cold thresholds) and Marstock test (combined warm and cold thresholds).

During cold winter days it is likely that people in buildings with older windows or high glass facades experience thermal discomfort due to cold air down draughts. Earlier work has been aimed at finding analytical methods to predict the speed of the airflow in a room and in practice heating appliances are often placed beneath the windows to reduce the draught along the floor. In a study from 2012 Mohammad Parchami developed a method for estimating the required heating power to counteract the downdraught with such heating appliances. In this study, Computational Fluid Dynamics (CFD) was used to evaluate the usefulness of Parchami?s method and also to examine the potential of adapting the depth of the inward window sill as a means of decreasing the down draught.

In Sweden, there are limits to how much leachable substances waste must contain in order to be deposited as hazardous waste. Fly ash from waste incineration often end up over the limit, mainly due to the chloride content. Fly ash is therefore often deposited abroad. The purpose of this study was to investigate the possibility to handle fly ash locally. To clarify how the law is applied, environmental reports and permit documents from ten waste sites with permission to deposit fly ash were studied.