A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

A current conveyor is an active building block that can be used to implement most active and passive components. It differs from the operation amplifier in that it uses current instead of voltage. The current conveyor also has significantly higher voltage gain over a broader frequency range. To simplify the construction of analogue circuits and increase the construction efficiency it is desirable to use a top-down methodology. This means that the whole system is partitioned into a hierarchy of subsystems.

This thesis should be regarded as an integrated research synthesis. The purpose has been to analyse how the literary sociologist Lars Furulands model the literary process correlates in relation to todays book market for fiction. The central problem has been: In what different ways can some of the main actors featuring in Furulands model of the literary process use, produce or provide copyright protected works of fiction which are electronically distributed? Three questions have been considered to penetrate this problem: In what different ways can to judge from some projects which have been carried through at common public libraries electronic works of fiction be provided to their presumed readers? What reasons could there be as it appears in a number of texts that four Swedish authors have chosen to disseminate their works of fiction by the aid of the Internet? Which main functions may, according to current research, be supported by electronic media in connection with editing and retail of fiction? During this study a picture of two quite disconnected processes of publication has materialized. These processes seem to proceed parallelly to each other, without any close contact, in a traditional respectively an electronic circuit.

In order to facilitate testing of anesthesia machines a patient simulator has been required by Maquet Critical Care AB. A patient simulator has been developed to reduce expensive and time consuming animal experiments and temporary lab arrangements. The patient simulator has been developed and designed to simulate human lungs with regards to anesthetic uptake, production of carbon dioxide and heating and moisturizing exhaled air.The system comprises a container and a test lung to simulate the volume and the dynamic of the human lung. The simulation of uptake of anesthetics has been implemented by pumping a fraction of the gas from the container through a bypass circuit with an active charcoal filter that adsorbs volatile anesthetics. The flow through the bypass circuit is generated by a pump and is controlled by a linear valve.The resulting performance of the patient simulator has fulfilled the requirements.

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

The thesis deals with three document retrieval models based on logic: the Boolean model,the fuzzy model and the Van Rijsbergen model.In Chapter 1, the author presents the purpose of the thesis. This is to give the logical foundationof the models, to describe them and to examine them critically. In Chapter 2, some importantnotions in document retrieval are presented. Chapter 3 is devoted to the Boolean model, Chapter4 to the fuzzy model and Chapter 5 to the Van Rijsbergen model.These three chapters are organized in the same way. First, the logical foundation of the modelis given.

Storing kinetic energy in a flywheel allows for more efficient driving of electricvehicles. Research in this area is in progress at Uppsala University, where a flywheelwith magnetic bearings encased in a vacuum chamber is being constructed. To makethis possible methods for measuring the current through the electromagnets in thebearings and temperatures in the flywheel need to be developed. This has been thepurpose of this report. The current measurement resulted in a resistive method, andthe implementation of eight measurement circuits in the system.

The Rya power plant in Borås produces district heating, district cooling and electricity. The plant is owned by Borås Energi och Miljö AB and is run by Dalkia Facility Management AB.In order to get the best heat exchange from the district hot water a pair of twin pumps and a turbine circuit pump are used as return pumps. Turbine circuit pumps are used to increase the pressure through the heat exchangers at the power plant. The pumps are in use when the flow is over 2 000 m3 h-1 and during the summer when re-cooling is used to improve the effectivens of the heat boilers.Since the pumps, that are parallel connected, rotating at a fixed rate per minute, the pressure is regulated with regulating valves. This report shows that during the 4,300 hours that the pumps where in use, energy corresponding to 590 MWh was wasted.

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

Ericsson AB in Katrineholm is a part of the Section Business Unit Network in the Ericsson Group. The plant's main task is to produce printed circuit boards in small volumes with a high product mix and focus on delivery and cost effectiveness. At the factory they produce printed circuit boards in the Module department.The Module department has for a long time had a high output of non-approved circuit boards in their production. This has led to a growing stock of non-approved circuit boards on the company?s repair department.The purpose of this thesis is to investigate how Ericsson in Katrineholm can increase the outflow of approved articles in their test process in the Module department.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

The interest in tiny wireless applications raises the demand for an integrated reference oscillator with the same performance as the macroscopic quartz crystal reference oscillators. The main challenge of the thesis is to prove that it is possible to build a MEMS based oscillator that approaches the accuracy level of existing quartz crystal oscillators. The MEMS resonator samples which Philips provides are measured and an equivalent electrical model is designed for them. This model is used in the simulations of the Pierce oscillator and the transresistance amplifier oscillator that are evaluated in this thesis. Finally the Pierce oscillator is implemented in the A BCD2 process and manufactured at Philips Semiconductors in Nijmegen, The Netherlands.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

The purpose with this masters thesis was to model the scanner in a system for laser bathymetry. The model was then used to develop a controller for the scanner so a good search pattern was achieved. Two different types of models have been tested, a physical model and a Black Box model of Box Jenkins type. The physical model has been derived from Lagranges equations. Identification experiments have been used to compute the Black Box model and to find the unknown parameters in the physical model.