The work covered in this report includes a literature study of the diesel dual fuel technology(hereinafter referred to as DDF). The literature study covers earlier work that has been doneregarding the use of compressed natural gas (CNG) and diesel in a DDF system. Moreover a onecylinder research diesel engine was fitted with a CNG fuel system for experimental testing. Theinstallation of the engine and the test cell is described. Results from the tests are presentedcovering emissions, heat release and pressure traces from the DDF-concept.During the literature study it was found that most research was related to heavy duty dieselengines.

Introduction: The current research shows that cannabis use is increasing, while alcohol use is decreasing in many countries. The reason for the increase is considered to be the increased availability and that adolescents attitudes towards cannabis has become more liberal. Aim: This qualitative study aimed to examine adolescents attitudes and knowledge about cannabis. Methods: Data has been collected from focus group interviews with adolescents aged 15-18 years, in a west Swedish municipality. Participants were recruited through visits to secondary and upper secondary schools.

The project, Glowtest Fixture, has been carried out to and in collaboration with MSA SordinLtd. MSA Sordin Ltd produces and sells ear protector and is at present a supplier on theworld market. Glowtest Fixture is a product for glow testing off detailed components in oneear protector. MSA Sordin Ltd sends today away your products for testing what is anexpensive aspect in their development. The project's aim is to take forward a test equipmentthat copes with those high nonplussed requirements and wishes that are required for anapproved physical execution.Glowtest Fixture is a physical equipment that comes used stem glow physical off all detailedcomponents in one ear protector.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

Due to the globalization today the competition in the market has in- creased and it requires flexibility and produce according to customer demand. In order to reduce the cost of wages industrial companies are now considering moving the manufacturing to low-cost countries. To keep up with the competition in the market without moving the manu- facturing abroad, Lean Automation was developed. The concept of Lean Automation is to reduce the perceived complexity with automa- tion and make automation available for new users and in new applica- tions.Haldex Brake Products are situated in Sweden and want to maintain the manufacturing of the automatic brake adjusters in the country. It is a product well-known and highly exposed to the competition in the mar- ket.

This report presents a master thesis project performed at Elekta AB during the fall of 2013 and early 2014. Elekta is a medical technology company and their main product in the Stockholm office is a gamma knife used for radiosurgery. The gamma knife contains a cluster of a dozen motor servos and motors used for adjusting the patient and the radiation sources over a CAN bus. A self-developed hardware-in-loop simulator running on a PC with LabVIEW is currently being used for integration level testing of the control system of the gamma knife. The simulator has some problems with it not running in real-time and having other performance issues.

This is a thesis presents a differential gear which is found in a tracked vehicle called BvS10. The tracked vehicle is manufactured by BAE Systems Hägglunds AB in Örnsköldsvik, Sweden. The differential gear has a bolted house. The differential meets the requirement specifications, but the problem is that the bolts are sheared off because of the extreme torque that the differential is exposed to resist.Previous report on the differential show pictures of bolts which have been sheared off at the threads. This report is also includes three lists that explain seven different proposals which some are approved and some are not, and the report also presents the force, tensile, and shear stress.In a bolted connection there is both axial tension stress and radial shear stress, which can lead to wear out and broken bolts.

While the technological infrastructure that enables collaboration between municipalities, counties and private health care providers improves, so does the need for health-care providers to gain access to the right patient journal at the right time. For doctors, nurses and other health-care organization employees this goal is achieved by NPÖ, National Patient Summary. NPÖ effectively enables health-care records to be shared across organizational boundaries. This thesis is based on a demand by a mobile application that can give district nurses access to health-care records wherever they are.This thesis describes the development of a prototype of a mobile application aimed for NPÖ. This includes investigating a suitable mobile platform, investigating available card readers for reading electronic identification from SITHS cards and the ability to connect to external services such as NPÖ.

I både kvalitets- och kontrollarbete finns det behov att kunskapsmässigt komma så nära verkligheten som möjligt vid fastställande av defektparametrar för oförstörande provning (OFP). Orsaken är att olika acceptanskrav och bedömningsgränser är svåra att klarlägga när man inte kan förlita sig på att uppgifter är realistiska. I projektet har olika erfarenheter använts för att få en bättre helhetsbild i området för defektparametrar och oförstörande provning.Denna rapport redovisar den inledande delen av forskning och utvecklingsprojektet PLANT 2, där olika defektparametrar kartlagts och en teoretisk bedömning utförts med avseende på hur signalsvaret påverkas för OFP-metoderna virvelström (ET) och ultraljudsprovning (UT) i form av puls-eko (PE) och ?time-of-flight-diffraction? (TOFD).Definitionen av redovisade defektparametrar följer i stort SKI-rapport 95:70 [1]. Defektparametrar i denna rapport redovisas i bilaga 1.Vid bedömningen av defektparametrarnas inverkan på OFP-tekniker, har drift¬inducerande defekter och tillverkningsdefekter hanterats separat.

I både kvalitets- och kontrollarbete finns det behov att kunskapsmässigt komma så nära verkligheten som möjligt vid fastställande av defektparametrar för oförstörande provning (OFP). Orsaken är att olika acceptanskrav och bedömningsgränser är svåra att klarlägga när man inte kan förlita sig på att uppgifter är realistiska. I projektet har olika erfarenheter använts för att få en bättre helhetsbild i området för defektparametrar och oförstörande provning.Denna rapport redovisar den inledande delen av forskning och utvecklingsprojektet PLANT 2, där olika defektparametrar kartlagts och en teoretisk bedömning utförts med avseende på hur signalsvaret påverkas för OFP-metoderna virvelström (ET) och ultraljudsprovning (UT) i form av puls-eko (PE) och ?time-of-flight-diffraction? (TOFD).Definitionen av redovisade defektparametrar följer i stort SKI-rapport 95:70 [1]. Defektparametrar i denna rapport redovisas i bilaga 1.Vid bedömningen av defektparametrarnas inverkan på OFP-tekniker, har drift¬inducerande defekter och tillverkningsdefekter hanterats separat.

This thesis describes how the chip space and coolant channels are designed in today?s mills, the ideas behind the design and what is considered to be the best method of cooling. It contains ideas on how the chip space can be simplified. It contains several concepts on how the cooling could be designed for better efficiency and manufacturability. There are also suggestions on how the cooling could be stopped when the cutter isn?t cutting.

This report is about finding the cooperative elements in games and making a boardgame based on them. I tested different computer games and boardgames to try and get the cooperative elements and then I make a boardgame based on what I found.What I found during testing is that to be a fully cooperative game all players on the same team must win or lose together and one player should not be able to finish the game by herself. There are of course some things that can change this for example what kind of players are playing.My best advice is that you should decide that the game is fully cooperative from the beginning and build the game from that..

Due to increasing product availability and higher demands on fast deliveries, the competition between companies is growing. To be able to satisfy the customers? requests an efficient logistics system with short throughput time is required. By using tools associated with Lean production companies are able to make great improvements in their manufacturing systems and reduce lead times to satisfy customer demands.There are two classifications associated with manufacturing, high variety and low volume (HVLV) and low volume and high variety (LVHV). The general belief is that the concept of Lean production is difficult to implement in a production environment with high variety and low volume due to the concept being adapted to mass production.

When performing studies that test the reactions of horses in different situations, important information may be available about the horse?s reactivity level. With information from these tests, accidents and dangerous situations may be prevented. When the behaviours from tests are compared with race performance it may be possible to evaluate if some behaviours are more desirable at the race track than others. The aim of this study was to see if behavioural responses correlated with physiological parameters (heart rate, cortisol), the trainer?s opinions and actual race performance.

Android is one of the leading software platforms for the new generation of smartphones. The market for applications is growing rapidly. So to be able to compete with such large competition the applications need a solid and stable development methodology. Therefore have we created an application based on a test-driven development, to investigate if the methodology was applicable on the Android platform. The conclusion is that Android?s suitability for test-driven development is dependent on the application that is being developed and if difficulties concerning the testing framework can be avoided.