When several production units provide a district heating network, water is pumped from different directions. When the flows from the plants finally meet in the network, the water can be completely still. These places are called zero flow zones. In district heating networks with several plants, which also have different supply temperatures, large and frequent temperature fluctuations can occur when the zero flow zones move. This may cause wear on the pipes, a phenomenon called low cycle fatigue.For this reason it is important to examine where and when zero flow zones that cause temperature changes occur.

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

The objective of this report is to present a review of the studies which has been carried out up to days date concerning how temperature affects vegetables physiologically when it comes to their health inducing as well as quality reducing features. The essay therefore starts off with defining what is meant by the terms health promoting and quality reducing features. It then moves on to describe how different subspecies of Brassica oleracea, that is to say vegetables such as broccoli, cauliflower, Brussels sprouts and kale, is affected by temperature. B. oleracea was chosen because the species contains several commercially interesting subspecies and therefore provides a broad field even though only one species is assessed.

Quality is the main focus in management of all laboratories. Accurate results of the analyses are not only determined by the analytical procedure but also by preanalytical factors. In the total analytical process of clinical specimens, there are many possible preanalytical sources of error. Monetoring of temperature on test samples of the transport boxes is one way to reduce the mistakes in the preanalytical phase.In this study, four laboratories from primary health care were invited to participate. The temperature has been measured on test samples of the transport boxes being delivered to the laboratory.In three cases the temperature remained within the limits, but in the fourth case the temperature varied more than the allowed interval.

Ribs from sheep, goat and pig are rarely assessed  to species due to the fact that they are very similar in their morphology and size. The ribs are instead considered unidentifiable although it is possible to see what kind of bone it is. If these ribs would be identified to species not only would species assessment degree of archaeological source material   increase, the relationship between meat-rich and meat poor regions would change.To find out whether there are morphologically measurable differences between sheep, goat and pig ribs, three measurement points on each rib has been defined and measured. At each measurement point two measurements were measured, one medial-lateral measurement and one cranial-caudal measurement. The ratio between the medial- lateral measurement and the cranial-caudal measurement was calculated for each point.

The aim with the thesis is to get deeper knowledge in one of the subjects botany, livestock technology or economy. I have chosen to get deeper knowledge in how to store potatoes. How are you going to act to keep the quality on the potato during the storage, with a minimum of weight lost? My aim with this thesis is to get a view over how the potato act in storage space. The storage environment is very important in the storage space.

By using steady-state measurements for predicting emissions under a dynamic drive cycle wouldsave a lot of time and money for the exhaust aftertreatment specialists at Volvo cars. The idea forthis thesis has been to investigate if statistical regression models can be used with good accuracy.Questions included are for example if common operating variables such as engine speed, air-fuelratio etc. is sufficient to predict engine-out emissions over the engine operating range with goodaccuracy. Focus was set on the modelling of warm engine, but also the more complex engineheat-up phase was investigated since it is a great contributor to total emissions. While NOxcouldnot be measured because of malfunctioning measurement equipment, only HC, CO andtemperature at inlet of first catalytic converter has been modelled.

Optimizing energy systems is, in Sweden, as in many other countries, of growing interest. District heating systems are no exception. In 2012, 285 out of 290 municipals in Sweden had district heating in use and the majority of these systems have a higher return temperature than that which is possible with an error-free substation of day current technology. To, when possible, lower the return temperature is a way of increasing the effectiveness of the district heating system.This study means to investigate, through simulations and calculations, how big of a reduction in production cost a lower temperature in the city of Ystad?s district heating system would correspond to.

Caran has a strong belief that women leaders affect the financial profitability positive. Since women leaders are intangible resources it is very difficult to calculate its exact value. The authors found that one of their measurement methods can’t be used to calculate the value of women leaders. The other measurement method can calculate significance between women and men leaders and provides an index to be compared to other groups. But there is no prove that women are better creating value than their men colleagues, the figures indicate that women add more value due to their lower wages.

This thesis studies the relationship between book values and market values in different assets and liabilities in Swedish Large Cap companies balance sheets. The aim is to find out if the relationship, the permanent measurement bias, has changed during since Mikael Runstens doctoral thesis from 1998 called The Association between Accounting Information and Stock Prices. Although some changes in the permanent measurement bias are found, this probably is due to other aspects than the introduction of IFRS..

The building industry consumes approximately 40 % of the total energy consumption in Sweden, where the using stage is dominating with 80 %. There is a lot of work in progress to reduce energy use in the building industry, and the demands from authorities regarding energy use increases. As a part of this work Building and planning department of Sweden has established a requirement that has been applied since 2006, and restricts a maximum energy use for buildings.The requirement includes that an energy simulation must be done in advance to demonstrate that it is possible to meet the demands.Reality is however more complex than an energy simulation program, that frequently underestimates the energy use of buildings. The purpose of this thesisis to study and analyse deviations between estimated and actual energy use in modern apartment buildings. The study includes four apartment buildings in Stockholm, Gothenburg and Jönköping that were built in 2007-2009.

Caran has a strong belief that women leaders affect the financial profitability positive. Since women leaders are intangible resources it is very difficult to calculate its exact value. The authors found that one of their measurement methods can?t be used to calculate the value of women leaders. The other measurement method can calculate significance between women and men leaders and provides an index to be compared to other groups.

In the spring of 2014 Sweco Systems AB were commissioned to design a ventilation system for a newly built preschool in Linköping. Terms from the client was that it cost efficiency would cope with the energy demands that are placed on the building. The unit chosen was a cross-flow heat exchanger, and this work is to compare it with two other heat exchangers to see if a more energy and cost efficient could have been chosen. The heat exchangers that was chosen for the comparison was a rotating- and a counterflow heat exchanger. Simulations have been made to the different heat exchangers by the manufacturers.

This report describes the building of a computer model that makes it possible to simulate the thermal climate in a greenhouse. The computer model is built on the physical theory of heat exchange that occur in a greenhouse, such as radiation and convective heat exchange. The model also includes the heat storage that is active in a greenhouse.The computer model is used to simulate the thermal climate in a greenhouse under three periods, winter, spring and summer. It also investigates which effect a concrete wall has on the thermal climate in a greenhouse. The purpose of putting a concrete wall in the greenhouse model is to investigate the possibility to store heat during the day and then use this heat when the temperature drops during the night.The result from the simulations shows that a concrete wall levels the big difference in temperature that normally occurs under a day in a greenhouse.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.