This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

As trucks are getting more and more advanced, information about their weight has become a key factor for controlling them in a more fuel efficient and safe manner. Knowing the mass of a heavy duty vehicle in real time has been a difficult challenge for the truck manufacturers. With the processing power for electronic control units in trucks steadily increasing, more advanced algorithms for calculating the mass has been developed, but at the moment there still is a wish for better performance.Since there is a lack of good information regarding the external forces acting on the vehicle, forces that depends on the slope of the road, foundation of the road and the wind, the methods have to be able to disregard these. Such an approach, based on an indirect least square solution, has been evaluated in this thesis. The results have been promising and based on these a recommendation about further evaluation has been made..

This report treats a Master Thesis performed at Scania CV AB. The task was to create a computer model of a hydraulic actuator system in the software AVL Hydsim. The system consists of two spring-loaded masses with surrounding hydraulic components. The purpose of the model is to study phenomenon and problems in the system, as well as to be a support in the development of the system. It is not supposed to be used to study absolute values in its current form.

Hemp is a versatile plant with many uses that has been around for thousands of years. The plant is highly adaptable andwill cultivate in almost any soil. It has excellent remediation properties and has shown to be relatively consistent when itcomes to crop yields. The aim of this literature survey is to examine how hemp can be used to be considered asustainable energy crop in Sweden through database searches and interviews. Hemps characteristics as an energy cropand its remediation properties is evaluated and compared with other plants that are used in Sweden.

The aim of the study was to look at a particular work group of housing supporters, whomhave implemented two special working methods in their work. The methods have been implemented by two of the housing supporters that also have special education in the methodsSOC (Sense of Coherence) and solution focused brief therapy. The study is based on anethnographic observation and analysis of documents that are used in the implementation. To analyse the information that was given at the observation and in the document I´ve used a theory which illustrates the significance of developing professions so their knowledge become legitimate. I´ve also used a theory that illustrates the importance of implementation and how it´s done at its best.

Den här rapporten har som syfte att utreda vilket eldistributionssystem för offshoreenheter som sparar mest vikt och utrymme. De två elsystem som jämförs är GVAs standard system och Siemens Blue Drive System. Rapporten innehåller en teoretisk bakgrund för båda systemen och dimensionering av systemens kraftkablar samt beräkning av kabelvikter och komponentvikten för systemen. För att uppskatta kabel- rutter och längder kommer ritningsunderlag för GVAs offshoreenhet 7500 att användas.Resultatet visar att GVAs standard system är det eldistributionssystem som har den lägsta totalvikten med 168 ton, GVAs standard system har en vikt som är 101 ton lägre än Siemens Blue Drive System som har en vikt på är 269 ton. GVAs standard system har en lägre ström vilket gör att ledararean blir mindre och i med det blir kabelvikten mindre.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Hammarby Sjöstad is a new district in Stockholm with high environmental standard. Stockholm Water Company evaluates a local wastewater treatment plant with cutting edge technology. The first step is an experimental treatment plant (Sjöstadsverket) with four parallel lines of treatment, each with a capacity to treat wastewater from 150 persons. Within the membrane technology subproject the possibility of using reverse osmosis (usually called RO) to regain nutrients is examined.Reverse osmosis separates the incoming water in a clean permeate and a concentrate that, as the name indicates, is a more concentrated version of the incoming water. Using this method in wastewater treatment, a solution high in nutrients can be obtained without the use of chemical precipitation agent and with no production of sludge.

The ability to tackle NP-hard problems has been greatly extended by the introduction of Metaheuristics (see Blum & Roli (2003)) for a summary of most Metaheuristics, general problem-independent optimisation algorithms extending the hill-climbing local search approach to escape local minima. One of these algorithms is Iterated Local Search (ILS) (Lourenco et al., 2002; Stützle, 1999a, p. 25ff), a recent easy to implement but powerful algorithm with results comparable or superior to other state-of-the-art methods for many combinatorial optimisation problems, among them the Traveling Salesman (TSP) and Quadratic Assignment Problem (QAP). ILS iteratively samples local minima by modifying the current local minimum and restartinga local search porcedure on this modified solution. This thesis will show how ILS can be implemented for MSA.

This study examinates technology's traumatic impact on the male subject in The Atrocity Exhibition by J.G. Ballard. In my analysis I show how the protagonist uses a fetischistic strategy in order to make sense of the trauma that technology embeds. Paradoxically it proves to be the agent of his trauma, but also functions as his shield. The machine is thus in a position of the hinge, the point in a structural system that both enables and deconstruct the system.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This report is an attempt to clarify how religious and non-religious views-of-life [livsåskådningar] are created through the collaboration and opposition of religious and scientific elements/ideas. This with the hope of reaching a fruitful result related to the solution of world-view related conflicts, such as the ones existing between science and religion, on an individual and societal level.This is accomplished with the help of two assertions: (1) Mankind has a need to explain its existence and surroundings. (2) Religion and science has their origins in the same seed and aim to serve the same purpose, or function. Together these two assertions lay the theoretical foundations of this report which implies that all humans have an innate need of sustaining a stable world-view.The result of this report is that a final solution to world-view related conflicts are beyond reach as our mental and physical nature limits us. However there are strategies for minimizing world-view related conflicts effect on society..

The purpose of this essay is to do an ecocritical reading of Vilhelm Moberg?s The Emi-grants from 1949. By asking and answering the three following questions; How does a system present itself, What are the different reasons for emigration; Why does differentsystem fit some well and some not.By using two articles from Green Planets - Ecology and Science Fiction to illus-trate two different views; Different parts value in an ekosystem and The Ship as an ecosystem. I have also created, based on the literary text four different terms concern-ing the dynamic system; Stable, Static, Unstable and Collapsing systems. I have found that all system goes through changes, some drastic, that changes the way the parts of the systems fit with in it.

This Thesis aims to explore how to integrate an IT-system for facilitating anorganizations work with Continous Impprovements.This is done here by examining and analyzing the process within a handful ofcompanies who seem to have been successful with their own implementations. Thestudy is focused on the implementation of one particular system, "System C2".Simliarities and differences between the companies, and the established rule of thumbfor these kind of activities are focused upon. This to emphasis how another actormight emulate some of the apparent success.Part of the core question is found in the title, since Continous Improvement is oftenseen as a relativly low-risk activity, is it then also possible to take a low-risk slow pathto the implementation of such a system in the entire organization?.

This thesis describes the development ofa linear guidance system suited for NORCAN's aluminium profiles. The work took place at LP Innovation, a small technical consulting company, located in Uppsala. The work started with gathering and searching for information. A lot of the information was found in product catalogs, but my supervisor was also a great source of knowledge, as well as the other engineers at the company. I also had the opportunity to work with the rea lprofiles, to get a feeling and greater understanding how they were supposed to be used. With the use of sketching and CAD, a number of concepts were generated.