This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

The European Water Framework Directive (WFD; 2000/60/EC) was incorporated into the Swedish legislation in 2004 through the ordinance Förordningen om förvaltningenav kvaliteten på vattenmiljön (SFS 2004:660). The objective is that all water bodies shall reach a good status by the year 2015. In Sweden the comprehensive plans of the municipalities can play a large role in reaching these goals. A comprehensive plan deals with the long term water and land use of the municipality, which can facilitate an early consideration of water management in the planning process of the municipality. In Sweden five river basin districts have been established in accordance with the Water Framework Directive.

The eutrophication of lakes and seas with the algal bloom and deficiency inoxygen that follow, has been given priority by the Swedish government as oneof 16 environmental objectives. The purpose of this project was to develop a toolbased on a simple model, limited amount of data and geographic informationsystem (GIS) to identify areas with risk for phosphorus losses due to surfacerunoff. This tool can act as a decision support to decide where appropriatemeasures should be applied with the aim of reducing phosphorus losses and bythat the eutrophication.The method that has been used is a combination of two models, one calculatingthe potential erosion while the other one identifies areas of erosion (net erosion)or deposition. This ability is of great importance because potential erosionshould be calculated on areas with net erosion. Areas with high potential erosionhave an increased risk for phosphorus losses due to surface runoff.The potential erosion was calculated based on factors which describe how topography(LS), land use (C), soil type (K) and precipitation (R) effect the erosion.All of them have been modified to a greater or lesser extent.

This bachelors thesis was made forWallenius Water AB to develop a basisfor an Airpurifier prototype. Wallenius Water isone of the world's leading environmentaltechnology companies engaged inchemical-free water treatment based onUV-radiation. The thesis aim was toproduce a basis for a prototype that canbe used in three applications:Standalone, RAS systems and ventilationsystems. The work includes anintroductory description of the theorybehind AOP technology based on aliterature review on the subject. Asurvey of products currently on themarket and a product specification hasbeen used as the basis for thepreparation of a number of concepts inthis report.

The sound part is mainly practical and is dependent on concepts that have been tested through measuring with a sound level meter. The design part is more theoretical and has been verified with CAD models and finite element analysis.With a sound damping hood on the compressor the sound level is reduced with up to four dB. An optimized absorbent for the compressor space gives a reduction with three dB. By using the insulation for the heat water tank as absorbent we can see a sound reduction on the lover octave bands. A reduction like this is elsewhere hard to achieve as at it requires thick absorbents.By changing the today?s insulation to the heat water tank to a form of polystyrene polymer insulation the weight from the heat pump above can be transferred to the stable heat water tank.

The present work is a continuation of the ideas developed in previous projects during my Masters studies that explored the relation between pattern, form and space. Starting from the pattern multiplication for space construction the present project proposes textiles as an assortment of flexible expressions. The purpose of the project is to explore aesthetic and functional potential of textiles for out door temporary structures. This is to create a pattern interface which filters sunlight through a textile surface to offer instant sheltering solutions for out door activities. The project combines research and analyses of outdoor temporary structures and scope of textile in the area.

A new build in the Swedish nuclear power system would entail increased re-quirements for the proposed repository, which is adapted after the reactors of today. With a fast reactor, capable of burning nuclear waste, operating in parallel with the light water reactors, the increased requirements on the repository could be reduced.In this thesis, simulations of a light water reactor and a fast reactor have been performed by using the Monte Carlo code Serpent to investigate the changes in the fuel inventory. The light water reactor in the study is a boiling water reactor and the fast reactor of the type sodium-cooled fast reactor and they have been used for three different operation scenarios.By studying the fuel composition and the results from the simulations of the three scenarios conclusions can be drawn. Conclusions regarding the change of the fuel inventory and decay heat in Clab as well as the interim storage facility and in the repository. Depending on the operation alternative the changes dif-fered significantly and especially regarding the mass of burned actinides for different fuels in the fast reactor.The lowest increase of fuel assemblies was meet when using 50 years old fuel with 20MWd/kg U burnout and 2,0 % enrichment for start up of the fast reactor and 30 years old fuel assemblies with 50MWd/kg U burnout and 4,7 % enrichment for the further operation of the reactor.The increase of the number of fuel assemblies was 3174, which is equivalent to 641tons of heavy metal.

In this report a study has been done regarding different heating systems on which are the mostcomprehensive with solar heating systems. The report has also been focusing if solar power can beused as a primary heating source for supplying more than 50 % of the buildings total heatingproduction. The University of Dalarna constructed a demo-house for this purpose and according tocalculations the total solar usage is more than 50 %. This house has been made for referenceregarding the design of the heating system of property 5:37.Further studies have been made to compare different heating systems that are compatible with asolar system, where the compared systems purpose is to be independent of direct using electricity. Asystem of this design is regarded as sustainable according to environmental as economic issues.

Stage-discharge equations for lakes without disharge measurementsSimon AnderssonIn 2015 all lakes, rivers, coastal water and groundwater should be of good ecological statusaccording to the water framework directive from the European Union. In the process ofimproving the quality of Swedish water bodies, knowledge of where problems occur isneeded in order to utilize the resources optimally. The ability of lakes to store water is animportant factor since it controls the flow of water through the country. A stage-dischargeequation is a mathematical relation between discharge from a lake and its water level. Bybetter understanding of stage-discharge equations for lakes, their storage capacity can bedescribed better in hydrological models.This master thesis aims to evaluate methods for determining stage-discharge equations forlakes where a variable amount of field measurements is available.

Uvån Hagfors Teknologi AB (UHT) has developed a process ? GRANSHOT® ? for quicksolidification of metals in water baths. In the process liquid metal is splintered ? granulated ?into small drops. The drops are rapidly cooled in a water bath where all the heat energy from theliquid metal is transferred into the water.

Hemp has been used for textiles for a long time in history until it became illegal to grow in many countries in the 1930s. It is interesting from an environmental point of view because it doesn?t need any pesticides and in most locations it doesn?t need any irrigation either, compared to cotton, which normally requires big amounts of both pesticides and water for irrigation. Hemp is a bast fiber, which means that the fibers are located on the bast of the stem (on the outer layer of the stem). Therefore they cannot be spun directly, they have to be removed from the stem first.

Most of the saw and pulp industries have stored wood nearby their production, the main reason is to have a continuous wood flow to the production. Wet storage of wood is of great importance to keep the wood quality. Without water sprinkling the risk of drying outand decomposition through biological activity increases significantly and will result in a negative effect on future production and quality. One drawback of wet storage of wood is the leaching of chemical substances into the surrounding recipient. The log yard run-off contains phosphorus, nitrogen, phenols and organic substances. These substances can cause problems for the surrounding environment. The main objective of this project is to gain an understanding of the wet storage used by the Swedish wood industry and estimate the environmental consequences that run-off water will have on the recipient.

Buffer zones play an important role for the water quality in our watercourses. When harvesting a forest close to a watercourse a buffer zone should be left. When it's not left, it will lead to radical changes in the environment for the water organisms. The overall purpose of this thesis was to illuminate the production- and environmental thinking when establishing new buffer zones in south of Värmland. The partials goals were to determine choice of tree species, ways of regenerate, occurrence of soil scarification and the occurrence of machine tracks in newly established buffer zones.

At present day there are several different methods for measuring of paved surfaces.The most common methods today are measuring with a total station, the GlobalNavigation Satellite System (GNSS) and terrestrial laser scanning (TLS). Recently thedevelopment of unmanned aerial vehicles, known as drones, has increasedexponentially and today there are several ways of using drones for measuring surfacesby photographing and laser scanning.This thesis contains a comparison between the methods terrestrial laser scanning(TLS), and unmanned aerial vehicle photogrammetry (UAV). The measurements havebeen applied on two different test surfaces, one of asphalt and one of gravel. Thepurpose of the comparison is to investigate whether the airborne photogrammetry isequivalent accurate in its height levels as the terrestrial laser scanning. For thecomparison to be more extensive, these two methods have not only been comparedin precision but also in the areas of ease of use and economy.The precision was analyzed by comparing the height levels in randomly placed controlpoints on the test surfaces.

ITT Water & Wastewater ställer höga krav på kostnadseffektiv produktion vilket är en starkt bidragande orsak till att företaget är världsledande på sin marknad. För att erhålla kostnadseffektiv produktion har kombinationen människa robot visat sig vara framgångsrik.Examensarbetets syfte var att ta fram underlag åt ITT Water & Wastewater för att ta beslut om frigörande av indirekt personal vid line 15:s isoleringsstation på Elmotorverkstaden. Syftets uppfyllande stöttades av de underbyggande syftena att försöka höja robotens utnyttjandegrad samt reducera isoleringsmaskinens omställningstid.Arbetet bygger på kvalitativa och kvantitativa data i form av mätningar, intervjuer och egna observationer. Med stöd av erhållen data lyftes fyra olika förslag fram. Förslagen understryktes bland annat av integrering av arbetsmoment, förhöjd automatiseringsgrad och outsourcing..