I denna uppsats beskrivs metoder för att skapa en arm i 3D samt att lägga in den i ett foto där den ersätter en riktigt arm. Anledningen till detta är att kunna skapa effekter i filmer och bilder som inte är möjliga med analog teknik. I denna uppsats kan man läsa om tekniker som används i varje del av utvecklingsprocessen och problem som uppstår samt lösningar och tips. I uppgiften finns det med delar som Modellering, Texturering, Rendering, Kamera Matchmoving och Compositing..

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

Intangible feelings of sorrow and grief, caused by events like separation, death, loss and trauma, all leave some kind of traces in us and they play an important role in our development. The individualistic society here in Sweden has shaped us to keep our feelings inside and at bay; since our childhood we have learnt that showing emotions like tears, sorrow and sadness are signs of weakness and can make others and yourself feel uncomfortable. With the starting point from my own experience and understanding of how we can deal and handle grief, I take a closer look on how jewelry, objects and rituals can be of importance in a grieving process and our lack of visual outer display of grief in today?s society. Through Sara Ahmeds theory I found a new possible way of understanding emotions and how they shape us.

The family and relatives caring for older people in Sweden lies on an old tradition. The responsibility to care for older family members has gone from family to the society. The aim of this study was to examine the needs of family caregivers and their experience of municipality support. This study includes only the family caregivers who have the main responsibility for the care of relatives and have support from the municipality. The caregivers were not allowed to work more than 50 percent in another job.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

Kulturvårdscentrum was a project that had great significance for local folklore societies in Bohuslän.Bohusläns museum was i charge of the project that lasted from 1987 until about 2001 when most ofthe original staff have retired. The staff was mainly recruited from a large shipyard, Uddevallavarvet,at it's closure due to recession. Financing was largely made by the government to help outthose unemployed who otherwise should have a hard time finding a new job. At start there was about25 employees who where trained for one year by staff from Swedish museums, conservation studios,and teachers the university. The education was aimed at serving local folklore societies, and dealingwith their special problems.

Today, there are more than 12 000-14 000 farms worldwide using an automatic milking system (AMS). Studies have shown that transition to AMS affects the udder health of cows adversely, recognized primarily as elevated somatic cell counts. There are several reasons for this, for example the greater variation in milking frequency seen in AMS. On one hand, short milking intervals may lead to bad teat condition of the cows due to the stress the milking procedure exposes the teats to. Too long milking intervals, on the other hand, seem to predispose for milk leakage, which is, in turn, a risk factor for the development of mastitis.

Inspired by how to sketch a light cone from a flashlight in a comic I wanted to create an armature carried only by its own light cone. To manage this challenge I sketched in an architectural and sculptural way, where I chose to ignore the function of the lamp as long as possible.As a result I developed an armature with a stunning shape, with an illusion that it was carried by its own light cone. It could be hanged on a wall, placed on a table, pushed against a ceiling or standing on the floor.Depending of its size the light cone from the light source lightens up the surface and draws attention to the otherwise forgotten wallpaper or the undisposed statue in the darkness of the city..

The eutrophication of lakes and seas with the algal bloom and deficiency inoxygen that follow, has been given priority by the Swedish government as oneof 16 environmental objectives. The purpose of this project was to develop a toolbased on a simple model, limited amount of data and geographic informationsystem (GIS) to identify areas with risk for phosphorus losses due to surfacerunoff. This tool can act as a decision support to decide where appropriatemeasures should be applied with the aim of reducing phosphorus losses and bythat the eutrophication.The method that has been used is a combination of two models, one calculatingthe potential erosion while the other one identifies areas of erosion (net erosion)or deposition. This ability is of great importance because potential erosionshould be calculated on areas with net erosion. Areas with high potential erosionhave an increased risk for phosphorus losses due to surface runoff.The potential erosion was calculated based on factors which describe how topography(LS), land use (C), soil type (K) and precipitation (R) effect the erosion.All of them have been modified to a greater or lesser extent.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

The background to this study is to find alternative ways of size rationalization. My vision is to take the basic conditions and make the best and most profitable of them. I have chosen press of rape oil because it?s interesting and the investment to get started is relative small. The opportunity to use outmoded and unrational buildings which often are found at many farms to something that gives money instead of costs money is also an argument.

Feline asthma is a condition very similar to the respiratory disease affecting humans. It is causing, among other things, a constriction of the bronchial airways, an increase of mucus production and damage to, or erosion of, the epithelial membrane. The symptoms occur intermittently and do, in most cases, evolve during a long period of time. The aim of this essay was to investigate whether there are any nursing routines for feline patients with asthma in animal clinics and animal hospitals in Sweden, and if so, to compare similarities and differences. A literary study of research material also led to a suggestion of how to form a nursing routine for this type of patient.

The problem, which I want to highlight in this essay, is about my fear of losing face in conversationwith the parents of my text. I'm going through different approaches to find out what is happening inmy meetings with parents. I will also see if the knowledge that I get will help me to get deeperunderstanding of my reactions in different situations and if this opens up new possible ways ofhandling them.In my text there will be two stories where the conversation with parents has been difficult. Theyboth illustrate my uncertainty concerning the unpredictability of conversations with distressed orstressed parents. I can prepare the environment, by cleaning and making it look nice before meetingwith the parents.