Individual cellulose ?bers were studied to identify the transport and absorbtion phenomena as well as the in?uence of drying. A Chalmers University of Technologydeveloped method within ESEM (Enviromental Scanning Electron Microscope) has been used in this study. The results from the laborations gave the following conclu-sions: The transport of water occurs in ?bers in the ?ber wall surface and the lumen.

Self-compacting concrete has soon been around for a decade. Recently the prefabrication industry has started to use this fairly new concrete type in larger scales, mainly because of its distinctive properties.  There are still certain areas that need to be thoroughly examined, such as bond capacity. There have been very few studies regarding shear capacity due to the fact that the procedure is complicated.This report will highlight a method to examine the shear capacity of different surfaces that have been prewetted as well as non-prewetted surfaces. The surface areas follow BBK 04?s and Eurocode 2?s demand for surface roughness.  A smooth surface will be completed in order to confirm if the different shapes influence the bond strength by shear stress or not.                       The purpose of this essay is to measure the bond strength within the shear capacity as well as examine the impact it has on surface roughness and treatment for shear bond.The method used to identify the shear capacity is called L-shaped Push-Off Test.

Gliding and sealing functions in Öhlins shock absorbing systems sets great demands onthe contacting surfaces. In this particular case, the bushings and the sealings on acylinder piston. The surface wanted is a surface with both low frictional forces and smallleakage. This study was done with the goals of investigating and determining existingsurfaces due to the frictional force and leakage. How can we in an easy mannerdescribe these?A number of ten front forks were part of a main study.

?Mechanical debridment ? A studie in irrigation optimization? is a final thesis which was executed by Fredrick Ekman, in close collaboration with the other group member Mikael Johansson, during the spring 2012. The thesis was carried out through Karlstad University Faculty of Technology and Science in the study program of Innovation and Design Engineering (180 ECTS credits). The client of the project was Medilink AB located in Lindesberg, and the contact person was Nils-Erik Söderström, Chief Executive Officer. The project was supervised by lecturer, Lennart Wihk, and examined by lecturer and professor Fredrik Thuvander at Karlstad University.

Planet rendering plays an important role in universe visualization and geographic visualization. The recent tools and methods allow better data acquisition, usually with very high resolution. However in computer graphics, there is always the limitation on the resolution of geometry and texture due to numerical imprecision. Not many applications can handle high resolution data effectively.This thesis introduces, Implicit Surface Scene, a level of detail scene management inspired by dynamic coordinate system and SCALEGRAPH? which change over time depending on the current camera position relative to the planet surface.

This thesis raises the problem with acid mine drainage around the closed mine Finngruvan.The purpose of the investigation was to compare metal content in surface water in the areaand its catchments between year 2010 and 2003, also to make calculation of specific runoffand metal load, furthermore determine the recipients in the area. Surface water samplingwhere preformed at the same place as 2003 and also at a few other places of interest. Adigital elevation file were used in GIS to calculate the area of the watersheds in the region,observations in the field where also made. The collected data were used to make comparisons,calculations and conclusions. The result showed that the surface water 2010 had somewhatlower metal concentrations.

Surface lift adapted for today?s user Today?s T-bar lift looks almost the same as when it was launched in 1938, even though a lot has happened in the ski and mountain industries. New equipment has developed without any major adjustment to the lift. Snowboard, sit ski and downhill biking are just some examples of the evolution that demands new seating positions. It?s also very common for families to spend their holidays in the mountains nowadays.

This master thesis has been done in cooperation with Sweco Viak AB in Sundsvall. The aimwith the project is to investigate the purifying effect of percolation filter due to iron andmanganese. The overall goal was to investigate how the parameters surface load,sandfractions, and burden time affect the purifying effect. The expectation is to optimize thedesign and find a demouldning of the filter that gives sufficient purifying with a highersurface load. As an attempt to accelerate the curing of the filter, experiments with a layer ofsand which surface has been covered with manganese ore (MnO2) on top of the filter havebeen done.As test filters 10 L bars were used and the experimental work was performed at thewaterworks in Hassela and Munkbysjön.In Hassela different sandfractions were tested.

A two-factor design of experiments done on GGAB for the identification of two selected factors influence on the length of the scattering of heat exchanger gaskets. The work consists of four parts: study, choice of survey method, the performance of investigation and analysis of the results. Chosen factors on the study are considered to be the most effecting of the length distribution of seals during the production of GGAB. The study is the first of its kind both in GGAB and in the rubber industry and has an experimental nature..

This thesis work is a 30hp D-level assignment in design as a co-operation between MälardalenUniversity and Scania CV AB in Södertälje. The purpose was to develope a close fitted catwalk.The market has seen an increasing value for these types of applications and have the ambition to keep up with the rest of the competitors. The catwalks of todays standards shall be estetical attractive, have a non slippery surface and be costefficient.While working with this project I have spent a lot of time with the concept proposals and with the evaluation of the concepts, resulting in a final CAD model and a approximation of the cost estimate. The new catwalk fulfils all the new recommendations and rules as sharp edges, ADR, the height of the stepup and a non slippery surface with built in drainage..

During the latter half of the 18th century, when concrete started seeing general use in modern cities, the use of different methods to give the concrete a finished surface texture saw use. One of these was using different methods of mechanically altering the surface using a slew of cutting and crushing techniques with mallet and chisel. This was done in order to hide the often dull and gray look of concrete, and allude to other more expensive and luxurious stones. The work would possibly have been done by experienced stonemasons, using much of the same techniques and tools they would have used while working natural stones. Or did they? This essay explores, through the use of traditional handcrafts and tools, the claim that the working of concrete surfaces can be done with the same tools and skillset as the working of natural stone.

Pulp- and papermills expend vast amounts of water in order to produce pulp, paper and cardboard. Hence, they alsocreate vast amounts of waste water which has to be cleaned before it can be released into the receiving body of water. Insuch a wastewater treatment plant, tremendous amounts of energy are expended by the aeration in the biologicalcleaning process. This aeration is necessary to supply the microorganisms that shall decompose organic material withoxygen, which they need for their metabolism. The transfer of oxygen from the gas phase to the liquid phase isprimarily inhibited by surface-active substances in the waste water like resin acids or fatty acids.

A project exploring the boundaries between 2D and 3D. What is surface and what is substance? A countinuation of previous projects where I?ve examined the journey from two dimensional paper to three dimensonal objects. This project deals with the journey from three dimensonality back into a flat two dimensional surface, and the question if something can be both 2D and 3D at the same time. I decided not to center the project around a specific item, but rather let the project itself be in focus.

Background Research concerning footing and its contribution to injuries has been conducted primarily in racing Thoroughbreds. Studies in UK and Japan indicate that some specific factors could be responsible for an increase in performance-associated injuries. Researchers in Sweden have performed studies on Standardbred trotters. More research is needed to be done on equestrian sports since requirements on footing are not exactly the same in riding and trotting horses. The lack of scientific evidence on the construction of equestrian surfaces has lead to anecdotal validation of designs.

This degree project has been carried out by Carolina Rapp and Jenny Tauson, students at Innovation and Design Engineer program at the Faculty of Technology and science at Karlstad University. The project was carried during Spring of 2009 and took 15 weeks of full time work.  Doppelmayr/Garaventa Group is an Austria/Switzerland corporate group and its associated company Doppelmayr Scandinavia lies in Sunne, Sweden. Doppelmayr/Garaventa Group is the world quality and technology leader in ropeway engineering. The degree project goal was to develop a new shaping of a surface lift. There are two kinds of surface lifts, platter and T-bars. The two kinds of surface lifts have some variation in design but only minor differences.