This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

The following essay aims to determine what textbooks and teaching media educators in the county of Västerbotten use when teaching the relation between religion and science. Based on educational science theory and through analyzes of factual texts, the teaching materials was examined to determine how much focus they put on the thematic of religion and science. The result shows how the different teaching materials affect this thematic differently. The main conclusion is therefore that students in Sweden could, depending on the teaching materials used in their education, be taught by different standards to reach the same requirements..

The purpose of this work is to investigate how 4-5 year olds perceptions of materials and material properties can be developed through an educational activity. The study is based on two interviews with eight children in that age category. The interviews were conducted before and after an activity where the children were first introduced to the subject by the tale of The three little pigs (Harris, 2009) and then given the opportunity to explore various materials related to the book. The kids got to experiment and explore how water affected materials and to compare different materials properties. The children were also attracted to build and create the material that was offered during the activity.

Background: A strong brand is becoming an increasingly important factor when surviving on a competitive market. A strong brand can therefore be considered a strategically important resource. The relationship between a brand's strength and its distribution can decide the future of a brand in the long run. Lifestyle branding is becoming a more popular way of differentiating ones brand from the competition. Purpose: The purpose of this thesis is to identify factors which according to the lifestyle brand owners are central when measuring the strength of a brand.

The number of people of getting allergic symptoms is increasing and the reasons are considered to be many. The human have changed their habits and spend more time indoor. In combination with new building technologies where denser housing constructions and new materials this causes bad indoor climate contributes to a higher occurrence of allergiesThere are several courses of action to deal with this problem. One action is by choosing allergy-free interior surface materials. An allergy-free material emits low concentrations of harmful substances resulting in a great indoor air quality.

The purpose of this study is to provide a description of how mathematics teachers in grades 3 choose to work with mathematics and how it affects of student performance in national tests. The categories I will use are outdoor education, textbooks, learning materials and problem solving. Laboratory materials can be everyday materials and educational materials in which pupils have an abstract understanding of the subject. This survey was conducted through interviews and observations. The survey was also conducted in relation to student performance in national math tests.

Volvo Cars in Skövde manufacture and assemble Volvo engines. When attaching the ignition coil to all 4-cylinder engines, a special mounting tool is required. This mounting tool is currently manufactured from injection-molded polyoxymethylene (POM), a thermoplastic. It has been noted that the life span of the tool is shortened as a result of abrasive wear that occurs during the attachment process of the ignition coil.An investigation of the possibility of manufacturing the mounting tool with a 3D-printer is undertaken in cooperation with ÅF, a consultant to Volvo Cars. A literature study is first presented to introduce broader knowledge on the subject.

Highland Group AB was helping a customer of theirs to create an All-Terrain Vehicle (ATV), a project Highland has never been involved with before. For the wishbone arms of the wheel suspension, traditional manufacturing methods and tubes with cylindrical or square shaped cross section was preferred. We performed a simulation where the ATV was driving on a bumpy road too see the forces involved. With the results we proceeded to calculate the strength of the concepts to find out which is best suited for the tough environment in which the ATV is used. The concept that turned out to be the best was a wishbone made of circular cross section, which had good structural strength and did fulfill the demands that we required for the construction.

Aim: The aim of the study was to investigate 1RM and what power could be generated in bench-press and half squat concentric at certain percentages of 1RM. Special interest was put to evaluate men (M) and women (K), strength trained (ST) verses non strength trained (EST) in generating absolute power as well as power relative to 1RM.Method: In total 59 subjects mean (± SD) age 24.9 ± 4.1 years divided into four test groups: 20 male non strength trained GIH-students (EST M), 20 female non strength trained GIH-students (EST K), 10 male strength trained - sprinters on national/regional level (ST M), 10 female strength trained - sprinters (ST K) on national/regional level. They did two tests on 1RM and power in events of concentric bench-press and half squat in a Smith machine. In the first test session 3 ? 5 lifts were made to measure 1RM in each event.

The automotive industry is increasingly studying lightweight solution in their designs, also rational production and low costs in materials and manufacturing methods are of great interest. This thesis consisted in the practical evaluation of anchors for sandwich panels. The object was to study loads of shearing and pull out of the plane. The experiments were carried out on panels made up of 1mm aluminium coatings and 50mm extruded polystyrene (XPS) at its core. As the fasteners used simple methods such as blind rivets, screw and glue.

To identify the exchange and adaptation that takes place in the business relationship between electricity suppliers and electricity customers and analyze how these factors affect the strength of the relationship.The investigated concepts create synergies. The strength of the business relationship in the current situation is dominated by weak reciprocity in adaptation and an inefficient exchange of information with low frequency..

These studies are done in behalf of Saab AB AVITRONICS in Järfälla in the form of a thesis atthe Royal Institute of Technology in Stockholm.The task was to examine the parameters that plays a role in the construction of modern radomesoperating in broadband applications.This was interesting for Saab to get an indication of which way they should go at the newdevelopment of radomes for the next generation of equipment for electronic warfare.After a thorough analysis of the influencing parameters, a optimization application was made toget a automated way to get a radome design by specifying data on the radome size, airloads,materials, etc.This is to minimise the time of the laborious work that radome development.inply.This was solved by letting ANSYS calculate the strength of the radome structure and MATLABcalculate electromagnetic data and cost models of different sizes and materials.All these parameters woven together with the optimization tool modeFrontier picks data from therespective program and perform an optimization algorithm and then iterate a step and sends thisdata to calculation programs for the new input data. In the end, we have received a convergedpoint with our optimal solution.For the presumptions and limitations for which applied for this thesis, the result was prettyintuitive. That is to say that the smaller radome - the less materal is needed and lowermanufacturing costs results in the cheapest solution possible. The reality is not so simple. Whereyou have to take more of the electrical details such as the effect on the transmitter as a majorfactor..

Publicity is argued to have relatively great impact on attitudes and behaviours of consumer. Especially great is the influence of negative information. At the same time it is likely for brands to be subject to negative publicity. Since companies are investing gigantic sums into buidling strong and positive associations around their brands it is of great economic interest to have a better understanding how negative publicity influence brand equity and what factors might moderate this effect. This thesis focuses on brand strength as a moderating factor of negative publicity.

Publicity is argued to have relatively great impact on attitudes and behaviours of consumer. Especially great is the influence of negative information. At the same time it is likely for brands to be subject to negative publicity. Since companies are investing gigantic sums into buidling strong and positive associations around their brands it is of great economic interest to have a better understanding how negative publicity influence brand equity and what factors might moderate this effect. This thesis focuses on brand strength as a moderating factor of negative publicity.

Being an architect I create spaces with roof, walls and fl oor. The availability of the essential materials to create such spaces is practically unlimited. The materials also play a significant part to the character of the created space. I hope to contribute to the general understanding of materials as elements in the design of urban spaces by having intensely explored one specific material in depth, pointing out its bad and good qualities. I am of the opinion that the reason for choosing a material shouldn?t be because of a shortage of knowledge, facts or references, but what character you want for the room. When travelling across Europe, it sometimes feels like clay paving is everywhere, but back in Sweden it is almost unseen of in modern landscape architecture.