This report summarize what have been done during the Master of Science Thesis that Klas Schjelderup has written for the company RANOTOR Utvecklings AB. The company is developing modern steam engines and this work should develop a machine to perform tests on a new type of piston seal that hopefully could be used in the future. The steam engines will be both volumetric and energy compact, around 1600hp/literof cylinder volume, and it will have a lot of practical applications.The new type of piston seal is hydrostatic lubricated which means that a fluid is separating two faces that normally is in contact. In this case pressurized water is used to separate the piston seal from the cylinder wall. RANOTOR have earlier formulated that at least the expander in the modern steam engine have to be oil-free, due to other components functionality in the closed water system.

The Homogeneous Charge Compression Ignition (HCCI) engine is promising in terms of lowNOx, low particulates and high efficiency. Due to its homogeneous charge, where thecombustion starts almost simultaneously from a number of points in the combustion chamber,only lean mixtures are possible to burn because of the resulting rapid combustion, which is muchfaster than the combustion in an SI-engine or a diesel engine. When richer mixtures are used thecombustion will start earlier and also be more violent.To phase the combustion later and lower the combustion speed, external cooled EGR can beused. The EGR-system used in this thesis uses a divided exhaust channel where one channel andits corresponding valve are used only for transporting EGR back to the intake system.Consequently the EGR-valve is connected to the intake pressure. This system is called Direct-EGR (D-EGR).Engine tests verified that the CA50 indeed is phased later when cooled EGR is used.

The task of this project was to build an computer processing system for pressureregulation, in which the pressure loss over the open hydrolicvalve should be kept as low as possible. By using an cross connected proportional directional valve the valve problem could be solved. The control- and regulationproblem for the pressureregulation system was solved by using the DAQ- card NI6035E from National Instruments and the computerprogram Automatic Pressure Control 1.0 which has been software developed and written in Visual Basic. The final result showed that correct processvarible was obtained in 0,5 seconds, when the setpoint was changed in the testarea 0 - 2,5 MPa..

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

Examensarbetet har genomförts på Siemens Industrial Turbomachinery AB i Finspång. Arbetet innebär modernisering av ventiler till ångturbiner. Uppgiften består av två delar, där den första delen är att modernisera dagens tätningar i spindelgenomföringen. Syftet är att finna en mer vibrationstålig, driftsäker och mindre utrymmeskrävande lösning. Det andra delprojektet är att finna alternativ till dagens tallriksfjädrar i de servomotorer som reglerar ventilen.

As emission legislations across the world continuously pushes engine development forward,engineers constantly need to come up with and implement fuel saving technologies. During thelast decade, variable cam phasing has become a popular solution to increase gas exchangeefficiency. This configuration is typically mechanically constrained by camshaft limitations, anda solution to circumvent this problem would be to use a different valve actuation principle.One example of this is to use pressurized air controlled by electrical solenoids. Such a systemhas been developed byCargine Engineering and this provides the starting point for this work. Tobe able to operate the valvetrain on an actual engine, a control system is needed.

The focus of this project has been on the drainage tank of the reheater on Ringhals 1. This tank has on two previous occasions received such a high water level that the system automatically emergency stopped. For this reason, events and various readings from these two occasions has been specifically studied and analyzed. In order to prove theories about what causes these problems a model of the system was created in the program Dymola. Using simulation results from the model, we have been able to demonstrate how the system's measured values should look likeunder normal conditions with respect to flows, pressures, temperatures, valve positions and water level in the drainage tank.

This thesis applies to a novel steam expander, one part of a steam engine system, a wobble plateengine. The piston in the expander moves axially with the outgoing rotating shaft and is locatedon a plate, why the engine type is called axial engine. When steam is applied to the plungers theplate wobbles creating a rotation on the shaft going thru the wobble plate. The steam expander issupposed to be used in exhaust gas recovery (bottoming cycle) applications and small scaleenergy production. The commissioner is Ranotor Utveckling AB.

Myxomatous mitral valve disease is a common disease in older dogs of small- to medium-size breeds. The mitral valve, and less commonly the tricuspid valve may be affected which causes them to leak blood from the ventricle to the atrium of the heart during systole. With increasing severity of mitral valve leakage the forward stroke volume ejected into the aorta decreases, which may lead to an increase in blood pressure in the pulmonary vein resulting in pulmonary edema. A decrease in cardiac output may lead to a decrease in blood pressure, but the body may respond in order to normalize the blood pressure. Franzén showed in 2007 that the systolic blood pressure was increased in dogs with severe mitral insufficiency.

AbstractThis report describes our ten week long thesis work which is the last task in our education in mechanical engineering at Linköpings University. The project has been performed at Siemens Industrial Turbomachinery AB?s service department. The company which is located in Finspång produces, sells and provides service for steam and gas turbines around the world.The purpose of this project is to help Siemens develop their maintenance programs for two of the auxiliary systems which are a part of the complete steam turbine system. These are lube and control oil systems.The project is restricted to two of Siemens maintenance products, No Stop Check (NSC) and the annual Safety Inspection (SI).

To invent an optimized product is a complicated process. This process is only half of the work. It is equally important to develop a production system that can produce the product in an  efficient and ergonomic way.After several evaluations of conceptual and detailed drawings a final idea has come to light.The idea intends, to the maximum extent, utilize the facility in a more efficient way through moving assembly lines and stations closer to the flock section and the stock for complete products. To make the production better, stations are placed in more logical places given the assignment they are supposed to accomplish. This improves the material flow radically.

The main purpose of this project was to make a survey of the steam and electricity consumption at Akzo Nobel Functional Chemistry AB and give suggestions of how to minimize them. These three different areas were focused on. First to make a survey of all the most important consumers, second to find the electricity consumption of the air compressors and the amount of waste heat produced from them. The third area was to calculate a model of how much fresh water that is used during a cooling sequence in the water based heating/cooling system of the reactors and give a suggestion of a suitable reuse for this water.The main result is a total survey of the energy consumption in steam and electricity. The survey shows that the second largest group after drying is heating of ventilation which gives big potentials of reducing the total steam consumption if there is a way of being self supporting in ventilation heat.

Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

The aim of the study was to compare how the population of pine (Pinus sylvestris) and spruce (Picea abies) have changed between 1927 and 2013 in the oak landscape south of Linköping. A field study was carried out in 22 two kilometre lines which also had been studied in 1927. In these lines, which where ten meters broad and had a direction from west to east, the pines and spruces were counted, measured and classified by steam diameter. The obtained result was that the basal steam area (m²/ha) had increased for pine (44%) and spruce (57%) between 1927 and 2013. The amount of trees had increased in all diameter classes except thinner pine and spruce with a diameter of 5-10cm.