AbstractThis work was assigned by a technological company that manufactures gas detectors in which the sensor signal is processed using digital filters. These filters have been developed by a consultancy firm which converted previously used analog filters to digital filters. The purpose of this work has been to analyse inadequate, and sometimes erroneous, documentation from the project in order to provide the company with know-how and tools for further improvement of their products. The work has been done using the simulation software COMSOL which was bought solely for the project. Analysis showed serious flaws as well as pure errors in the consultant?s documentation.

The purpose of this thesis is to investigate the possibility to make small, cheap and ultra low power sensor platforms, connected in wireless networks for monitoring of home and industrial environments. The concept is based on ideas from our supervisor, Jerry Lindblom. The developed system consists of a generic platform for different sensors, a receiver and software. A GPRS module from RO Rollytech AB and a database from Gema Industri AB have been modified and used to demonstrate an example of a complete system. To the platform, it is possible to connect any resistive sensor and any sensor that can act as a switch.

This paper describes the work done trying to diminish the noise present in the signal from an IR-detector. The project was aiming towards two different kinds of applications; heat protection and presence detection. The hypothesis was that the signal-noise ratio would decrease if a filter and a proper installation were used for the detector. Some experiments were executed to determine what kind of filter were the most suitable for each application and how these could be installed. After executing the experiments and evaluate the results we recommend to use a specific filter for each application.

Denna rapport behandlar utveckling av en tvåhjulig balanserande robot. En PID-regulator är implementerad i en mikrokontroller, som även AD-omvandlar en sensorsignal, samt styr motorer via H-bryggor med pulsbreddsmodulering. I rapporten förklaras framtagning av diskret PID-regulator, processorkort, motorkort, val av komponenter och sensor för att mäta robotens vinkel mot ett vertikalplan.Roboten kan balansera stillastående, men behöver kompletteras ytterligare med hjulåterkoppling för att kunna balansera medan den kör. Roboten balanserar med mätdata från en mekanisk golvavkännare (potentiometer). Andra sorters sensorer diskuteras också, t ex accelerometer, gyro och optisk sensor..

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

Denna rapport presenterar en metod som möjliggör bestämning av bredbandiga signalers infallsvinklar. Studien är gjord i Matlab där infallande signaler samplades med ett antal sensorer utplacerade ekvidistant på en rätlinje. Den samplade informationen viktades sedan med konstanter framtagna med en konvex optimeringsrutin för att bilda en vinkelberoende utsignal.Rutinerna testades för insignaler med ett få antal frekvenser och gav för alla testade insgnaler en mycket bra bestämmning av infallsvinklen. Studien visar även att det är möjligt att göra systemet mer robust mot störningar i sensorernas positioner genom att ställa kriterier på den konvexa optimerings rutinen..

This examination work on studies and research in articles is mostly from other countries. The purpose of the examination work have been to find out if there are any means you can work with to find out when its time to start irrigation, how they works and if they are credible. In Sweden there is not many means for decide when it?s time to irrigate and how much water you should appear. Swedish farmers think they have so much experience that they don?t need techniques like this.

Sweden is considered to have one of the world's highest animal welfare standards in agriculture. Despite this, there are shortcomings in animal husbandry. One example is overcrowding, which is a way to increase stock size without making costly investments in the buildings. It can be carried out systematically to increase profitability or due to, for example uneven calving during the year. The European Commission criticizes the fact that stocking density is not controlled under Swedish welfare inspections.

Sweden is considered to have one of the world's highest animal welfare standards in agriculture. Despite this, there are shortcomings in animal husbandry. One example is overcrowding, which is a way to increase stock size without making costly investments in the buildings. It can be carried out systematically to increase profitability or due to, for example uneven calving during the year. The European Commission criticizes the fact that stocking density is not controlled under Swedish welfare inspections.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

The aim of the Master?s Thesis work is to study and develop algorithms for autonomous travel of a UGV (Unmanned Ground Vehicle). A vehicle for the mounting of sensors has been constructed in order to perform the work. Since the UGV is to be used outdoor in urban areas, GPS can be used. To improve precision and robustness, inertial navigation is used in addition to GPS, since GPS reception is likely to be diminished in such areas.

A method for equine intra oral radiology has been tested. In the study, both a digital system with an intraoral sensor connected to a laptop and a system utilizing image plates and digital developing was tested, initially on cadaver sculls and finally on sedated horses. The digital sensor was not considered viable for this purpose, while the system with image plates and digital developing worked very well. Two different techniques, i.e. parallel and bisectris, are suggested for the best visualization of different parts of the teeth. Intra carious injections of Mixobar oesophaghus contrast fluid was found useful when evaluating the extent of carious lesions. Compared to extra oral radiology, the new method had several advantages and can be used both in clinic and field practices..

To be allowed to sell Z-suspended vehicles with dipped beam Xenon or LED lighting, Scania have to develop automatic headlight level control. This master?s thesis aims to be the foundation to that development.The thesis consists of several parts; a market analysis of how competitors to Scania and the general vehicle industry solve this problem; several available principles for detecting the amount of control needed; the construction of a test station for sensors, a control unit and components connected controlled by the control unit; a further theoretical and practical development of one principle ? one rotational sensor connected between the chassis and the back drive axis; a state flow model programmed in Simulink that produces the control signal for the headlight leveling from the sensor input.Lastly the thesis gives some recommendations to the further development and implementation of automatic headlight level control on Scania vehicles..

Denna rapport behandlar utvecklingen av en prototyp för en absolutläges-sensor, benämnd AOS. Arbetet är utfört på uppdrag av Electrum Automation AB som med hjälp av prototypen vill utvärdera om en skarp produkt kan tas fram genom att använda billiga sensorer främst avsedda för konsumentbruk. AOS ska kunna användas för att mäta absolut orientering, dvs. lutning och riktning i förhållande till jordens gravitation och magnetfält. Den ska kunna appliceras i tuffa och säkerhetskritiska miljöer, t.ex.

Geodata finns idag tillgängligt via geodataportaler runt om i världen. På dessa geodataportaler beskrivs datamängder och tjänster som kommer från olika myndigheter. Geodatasamverkan har uttryckt intresse för att kunna beskriva realtidsresurser på dessa portaler med hjälp av metadata. Utifrån ett samarbete mellan SMHI och Lantmäteriet har denna studie tagits fram där en dynamisk realtidsresurs från SMHI testas beskrivas med Geodataportalens nuvarande struktur. Befintlig litteratur har undersökts för att presentera en bakgrund.