This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

A helicopter based system equipped with a millimetre-wave fire control radar is studied for improvement of the detection probability for moving ground targets. The system is a pulse doppler radar that sends out the electromagnetic wave in repetitive pulses. The frequency in which radar sends this pulse is called Pulse Repetition Frequency (PRF). The velocity of the moving targets is measured by spectral analysis of the pulses received. With this sort of system some targets will not be possible to detect.

The construction industries are relatively conservative type of business that takes a longtime to adjust for new methods and embrace new ideas. It dose not matter if the newmethod seems to be an improved method as long as it is new and untried. Constructioncompanies are reluctant to change form a longtime working method to a relativelyunknown method.The purpose with our report is to perform an evaluation of BeWi construction method.Our goal are to present the generally opinion about BeWi from the contractors that hasbeen in contact/worked with the method. We also want to know from the contractor?spoint of view if BeWi and the method measure up to the standards that are presented byBeWi and if they believe that improvements need to be done.Our progress up to the final report has consisted of three parts[1]Field studies[2]Interviews[3]Literary studiesWe started out with field studies where we took notes and observed all the includedworking phases on the construction site when using the BeWi method.

This reportcommunicates the processes and results of my degree work in industrial design at candidate level at Umeå Institute of Design.During my degree work I had a cooperation with Svenska Jägareförbundet (Swedish Hunters Assosiation).The aim for my project has been to explore how I could make hunting a safer hobby and undertaking. Every year people get seriously injured and in average 2 people a year dies  due to hunting accidents. My goal is to identify problems within the hunters communication and approach. Through a creative design process I will find a valid  nd realistic solution to these problems. My project will be presented as a conceptual solution  hat will be based on currently existing technology.

This report is an attempt to clarify how religious and non-religious views-of-life [livsåskådningar] are created through the collaboration and opposition of religious and scientific elements/ideas. This with the hope of reaching a fruitful result related to the solution of world-view related conflicts, such as the ones existing between science and religion, on an individual and societal level.This is accomplished with the help of two assertions: (1) Mankind has a need to explain its existence and surroundings. (2) Religion and science has their origins in the same seed and aim to serve the same purpose, or function. Together these two assertions lay the theoretical foundations of this report which implies that all humans have an innate need of sustaining a stable world-view.The result of this report is that a final solution to world-view related conflicts are beyond reach as our mental and physical nature limits us. However there are strategies for minimizing world-view related conflicts effect on society..

The goal of the project was to create an extension to Internet Explorer forStatens Tjänstepensionsverk (SPV) which would give the staff the experience ofSingle sign-on (SSO) to external web service providers as well as manage andupdate their passwords in a secure manner. The survey focused on the providersPalasso, ProCompetence and Wera. The extension was created as a BrowserHelper Object (BHO) with C# in .NET. The solution was implemented as aCOM object in a DLL-file that was running in-process with the browser. Theprogram used a locally stored XML file containing URLs, usernames andencrypted passwords to the providers.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Through previous studies during my education, I have experienced that chemical deicing road salt is a known problem, mainly in southern Sweden. Road salt causes damage to the environment and also damage to vehicles and structures such as bridges, etc. Road salt causes vehicles and steel constructions to rust, leading to increased costs for repairs of damage to structures. Road salt also causes damage to the plants and the economy to suffer, when plant material and soil needs to be replaced. In order to get closer to a solution, I put up three questions.

The constant need of energy is something that affects us all no matter our current situation. Whether we are driving our car to work, taking the elevator or using the oven to cook dinner we end up relying on energy. Our whole society is continuously striving to achieve a higher grade of efficiency and the process of supplying ourselves with energy is no exception. The importance of appliances in our everyday life cannot be exaggerated and thus the importance of their high efficiency.Efficiency is already a keyword in the appliance industry with labels, stars and numbers helping us choosing the most suitable option for the task ahead. No matter how efficient appliances often use pure electricity as their energy source.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.