Sweden?s energy consumption is divided into three major sectors. One of them is the industry sector. One third of Sweden?s energy consumption is converted in the industries.

Gtherm is an innovation company who has an unique air heat exchanger underdevelopment. The purpose of this thesis is to provide data of suitable motors for theheat exchanger and to find suitable motor suppliers.A motor specification was designed. It is an important basis for the search of suitablemotors. A compilation was made of nine motor suppliers and the suitable motorsfrom those. The compilation can be used by GTherm in their choice of suppliers andmotors.The compilation of the demands on the motor and analysis of suppliers indicated thatthere were no standard motors available to GTherms air heat exchanger.

This report is made as a literature review, focusing on the work done to increase understanding of efficiency in the categories of substations and secondary heating systems, with respect to the deviation from the theoretically possible cooling off in the distribution network as well as the economic benefit that appear. The main purpose of a considerable part of the literature used in this report addresses the issue of identifying individual causes of reduced cooling in district heating systems. These literature resources have been compiled and summarized as part of the report.The technology of district heating is associated with benefits such as better use of the energy in a fuel. This is the case of cogeneration plants where serial generation of electricity and thermal energy increases efficiency compared with the parallel generation where heat is generated locally and electricity is generated centrally. Serial generation thus allows for lower primary energy demand.

Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

The world is currently facing a huge severe challenge in handling the issue of climate change. One of the ways to lower the green house gas emissions, which is seen as one of the main contributor to the climate crisis, is to use renewable technologies such as for example photovoltaic (PV) systems. PV-systems are also suitable for so called micro production, small scale energy production facilities, since it can be placed on practically any rooftop with the right solar conditions. In Sweden the usage of PV-systems has not yet gotten any wider spreading, even though the solar radiation conditions are very similar to countries that produce a lot of solar energy, as for example Germany. The aim of this paper is to describe non-adopter perceptions of PV-systems. The study holds a qualitative approach using deep interviews for data collection.

The dishwasher is a wide spread product that occurs in many households. It saves the user time,water and energy. When using a dishwasher instead of doing dishes by hand a lot of energy issaved.The importance of lowering the energy consumption does not only come from the consumerwinnings but also from an environmental point of view. Scientists are certain that the globalwarming comes from the emission of green house gasses that is created by human consumptionof oil, gas and coal.Dishwashers today are a lot more energy efficient than older dishwashers, but there are stillmargins to lower the energy consumption. The aim with this project is to investigate thedishwasher and it?s washing cycle, noting different phases and components that contribute towaste of energy.

The aim of this thesis is to develop a new business model for district heating and cooling firms which can contribute to a stabilization of the Swedish national energy system. The business model is developed for a district heating and cooling firm and is exemplified with Fortum Heat. The theoretical investigation around the topic creates a rigid base for following qualitative empirical studies. Osterwalder?s canvas for business model generation is used together with a Casual Loop Diagram to identify a number of business opportunities which stabilizes the national energy system.

I följande rapport behandlas ämnet förnyelsebar energi i samband med textila material. I resultatet ges förslag till möjliga tillvägagångssätt för integrering av flexibla solceller i väv- och varptrikå. Alternativ till maskintillverkare och maskintyper redovisas och potentiella användningsområden diskuteras. Även förlag på typ av flexibel solcell presenteras. Teorin vilket rapporten grundar sig på är humanekologisk.

Construction of an autonomous wind station was a project with the goal of creating a product that could collect wind data from a sensor and then transfer this data to a server wirelessly over the GSM network. The device would be powered by batteries and solar cells and function fully without requiring external power supply. This required that a small computer was constructed and programmed to store and send data at predetermined cycle times and programming of a server that received the sent data. The project also required optimization of power consumption and dimensioning of solar cells and batteries based on this. The construction of this station demanded research both for the selection of hardware and programming software. The computer was based on a microcontroller and a GSM module that sent the data over the 2G network.

In 2010, Airwatergreen AB started testing their new technology, the Airwaterwell, an atmospherical water generator of their own design that is running on Solar heat, with a production capacity of three litres of water per day and m2. The purpose was to focus on foreign aid organizations as main purchasers for project investments towards rural communities in developing countries that suffer from lack of, or compromised quality of drinking water. In order to further understand if this technology would bring a positive impact in the developing countries, the company contacted the Swedish University of Agriculture for a socio-economic study of the Airwaterwells? potential. The authors elected Cost benefit analysis as the appropriate method for conducting the study and India became the study region because of its many problems with water related issues such as diseases as well as insufficient water supply for households. The regions that this study is based on are Gujarat, Haryana and Uttar Pradesh given their differences in income, health situation and poverty rate.

The study aims to reduce energy consumption in apartment buildings where individual metering and charging of heat is applied. The aim is to develop planning and design for individual metering and charging in apartment buildings.The study is based on literature review, interviews and case study that include analysis of existing documents. Interviews were carried out with the property developer and the involved consultants who planned the apartment building Yasuragi. To investigate the differences the condominium association has noted in heat consumption between flats, the debit values of the heat were used to discern which houses that were furthest from the average consumption. On these flats there were temperature measurements and thermal photo shoots made for discriminating behavior and possible construction techniques which could be the explanation for the heat spread.Boverket shows that the consumption of heat can be reduced by 10-20% after insertion of individual metering and charging in an apartment block.

This degree project handles acoustic measurements of the heat pump EcoAir 107, made by Enertech CTC AB. The sound from the three sound sources of the heat pump, fan, compressor and four way valve, have been measured to find out how they affect the total sound level of the product.Measures to attenuate the sound level have been developed and tested. By comparing these with the sound of the heat pump, in its original state, we have found out the measures which have best effects.The best attenuating measures came to be: taped openings and holes around the compressor space, isolating the top and the bottom of the whole construction, support of the fan bottom part and shielding of the sound source with a screen at a distance of 110 mmThese measures have been tested together and an average attenuation of the total sound level with 3,9 dB have been accomplished. In the front of the fan where the continuous sound is the strongest, the attenuation was 4,7 dB.This project is meant to be used as a guide by Enertech CTC AB:s during their future developing process..

In Sweden there is a large interest in renewable energy but the market for solar power is still small compared to other countries such as Germany. Here many farmers produce their own electricity. The Federation of Swedish farmers have acknowledged the potential for Swedish farmer to produce electricity and there is an interest among the farmers. The agricultural branches in Sweden most suitable for solar power are pig production and poultry due to the even electricity need throughout a year. Swedish pig farmers are going through a period of unsteady profitability which makes it interesting to see whether producing their own electricity can affect the economic situation.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.