This master thesis was done for a company called BRUKS which is active in woodprocessing,bio-energy and bulk material handling industry. The idea for the master thesis wasto develop a new reclaiming method for silos where wood chips are being stored. A mediumsegment of between 1000 ? 5000 m3was defined as the segment with the most sales potential.Two different concepts were produced, one for new constructions and one for rebuildingalready existing silos.In the beginning of the master thesis a lot of time was spent on visiting different BRUKSoffices and customers to get an overview of the industry and the product. This informationwas the basis when the idea generating phase began.

Biogas is a renewable energy produced through anaerobic digestion, which means that organic matter is degraded by microorganisms under anaerobic conditions. The produced biogas can then be used for cogeneration, electricity, heat or upgraded to vehicle gas. Eskilstuna Energy & Environment AB has four digesters at Ekeby water sewage treatment plant, Eskilstuna. One of the biogas reactor (RK4) is equipped with a jet-mixing system while the remaining digester uses top-mixing. The mixing system is an important parameter to achieve optimum operating conditions for the process regarding gas production and degree of digestion.

The purpose of this study was to investigate whether resistant maltodextrin is suitable as a fiber source in the probiotic fruit drink ProViva Mango without affecting the probiotic bacterium Lactobacillus plantarum 299v, viscosity or the sensory experience of the drink. Resistant maltodextrin is produced from hydrolyzed corn starch and is classified as a soluble dietary fiber. It is relatively resistant to digestion in the small intestine, where approximately 10% can be broken down, 50% can be fermented in the colon by the intestinal flora and 40 % is excreted in the faeces. Resistant maltodextrin has several important qualities when it comes to food processing. When added in a product, it does not affect the viscosity or taste and it is heat and acid stable.

Under de senaste årtiondena har det pågått en förtätning och en alltmer ökad utbyggnad av världens städer. Som en följd av detta har stadens naturliga vatten- och värmebalans rubbats. På bekostnad av vegetativa ytor har artificiella byggmaterial introducerats som absorberar värme från solens strålar och höjer stadens temperaturer. Dessa material leder även snabbt bort regnvatten samt hindrar vatten att infiltreras ner i marken. Temperaturskillnader på 12oC jämfört med den omkringliggande landsbygden har kunnat uppmätas i stora amerikanska städer. Detta fenomen har kommit att kallas Stadens Värmeö eller Urban Heat Island som är den engelska termen. I Sverige förväntas det bli allt högre sommartemperaturer och fler rekordvarma dagar framöver.

Sala Silvergruva AB är ett av många företag som just nu kämpar med höga energi-kostnader. Denna rapport undersöker vilka möjligheter det finns att skapa ett hållbart energisystem i Sala Silvergruva med avseende på ekonomi, miljö samt sociala aspekter. Rapporten undersöker nio tekniker; vindkraft, vattenkraft, solfångare, solceller, pelletspannor, värmepumpar, effektivisering samt lagring av värme från växthus respektive fjärrvärme. Dessa analyseras var för sig med utgångspunkt i tio krav som speglar hållbarhetsaspekterna. I samband med analysen ges rekommendationer angående investering i respektive energilösning. Rapporten mynnar ut i en resultatskarta där det tydligt framgår vilka krav de olika teknikerna uppfyller. Den följande diskussionen leder fram till en slutsats som presenterar vilka åtgärder som bör vidtas i syfte att skapa ett uthålligt energisystem för Sala Silvergruva AB. Pelletspannor och värmepumpar visar sig i nuläget vara de mest uthålliga tekniklösningarna.

The purpose with this report is to make a contribution to Bodycote heat treatments workshop in Värnamo, how to introduce, establish and constantly improve its environmental system. The rapport will help Bodycote with there certifying in ISO 14001: s demand standard. Organizations who continuously work with environmental issues have a lot to gain. Two things an active environmental development process will convey are, building of thrust within the circle of customers, and great financial savings. An increasingly numbers of organizations realize the importance to introduce a functioning environmental system into their activity.

Since prehistoric time man has used wood to build their environment. The material?s availabilitycombined with its good mechanical properties has often made it the material of choice. Like allmaterials exposed to natures degradative processes the properties of wood decreases over time.Rot, UV radiation and attacks by insects and pests damage wood if not protected. Since we wantwhat we build to consist, optimizing our building materials durability is of great interest.Techniques and methods for increasing the endurance of wood have been developed in severaldifferent places and for a long time.

This thesis has been performed at Scania CV AB Technical Centre in Södertälje and its aim hasbeen to study the causes and effects of deformations in the interface between the rear axlehousing ADA1100 and the central gear house R780 during operation. Design changes that wouldincrease the sealing capability of the studied interface are also suggested. Finite element (FE)and CAD software have been the primary tools in this study.Finite element (FE) simulations are used in the industry to predict and develop engineeringdesigns. The main motive for FE simulations has traditionally been to identify weak spots in thedesign, regarding high tensions and large deformations.The FE model is an aggregation of submodels and interface models that represents the rear axlehousing, suspension, central gear, central gear housing, wheels, bolts and weldings, and theirinteractions. The submodels have different material properties and they are connected withcontact interface models.Boundary conditions are defined on the bushings in front of the rear axle and on the air bellowsbehind the rear axle.

The voltage level in the power grid varies due to variations in load and production. Normally these variations are manageable, but they may be excessively large during a disturbance. If the voltage is too high it may damage the equipment in the grid and too low voltages may cause problems like voltage instability. The magnitude of the voltage variation depends on the short circuit power capacity of the point of interest.This problem may become lore prominent due to automatic voltage regulation that acts on shunt reactors and shunt capacitors. When the shunt reactor is connected or disconnected to the grid it may cause such large changes in the voltage that the shunt reactor starts hunting.

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

Safe operation of a large synchronous power system as Nordel is not an easy task.There are several aspects to take into consideration. This thesis focuses on the problems due to voltage collapses in a transmission system.The ability to foresee an upcoming collapse is vital to maintain stable operation of the grid. The grid operator at Svenska Kraftnät (SvK) uses the computer program SPICA to predict the maximum transfer limit at specified transfer sections. SPICA uses actual states from the grid to predict the transfer limitation, and a quarter later a renewed estimate is produced and so on. This means that the operator can se his transfer limits vary every fifteen minutes.Our task in this project is to validate the accuracy of the limitations obtained by SPICA.

Biogas mainly consists of methane and carbon dioxide, where methane is theenergy-rich gas, and is naturally created when organic matter breaks down in absenceof oxygen, also known as anaerobic digestion. A biogas plant re-creates the anaerobicconditions inside a digester where the organic substrate is fed into and digests toproduce biogas. The gas is then used to produce energy by combustion and can beseen as a completely renewable fuel.Today, energy from biogas is used primarily by major stakeholders such asmunicipalities and thus the plants become very large with high investment- andconstruction costs. There are currently few small plants in Sweden, even though thepotential for agriculture and medium-sized to smaller farms to become self-sufficientin terms of electricity and heat is great. Farms have a natural stock of digestibleorganic material in form of manure or crops for example, which are constantlyavailable.

Transmission of reactive power is well known to cause active power losses. Thus, newcomponents who can help minimizing these expensive reactive power flows are ofgreat interest to the power distribution companies. ABB Corporate Research hasdeveloped the first electronic power breaker. One possible application for thisbreaker is transient-free switching of capacitor banks. This could prove a usefuldistribution voltage complement to the switch-sync technique, mainly applied to transmissionvoltage level.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Mankind faces a serious threat. Its activities, for example the burning of fossil fuels, have led to an enhancement of the greenhouse effect - something that has given rise to a global warming. The climate is becoming warmer, a change that has important effects on the nature as well as for humans and their society. Sea level rising, extreme temperatures are becoming more common, glaciers and other ice caps melt and storms becomes more intense when they appear. The main cause is the emission of greenhouse gases into the atmosphere - carbon dioxide in particular.