When farm animals are transported there are several factors that can affect their welfare. If the vehicle has an accident the welfare of the animals transported will probably be compromised. The aim of this study was to make a survey of accidents with animal transportation vehicles in Sweden. The survey included the number of accidents from January 2000 to May 2014, the cause of the accidents and how the animal welfare was affected by the accident. The authorities which were likely to have reports about accidents involving animal transports were contacted. There were no collected records about transportation accidents and the authorities referred to eachother for information.

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

I want to look at the possibilities to start selling hot water from a small district heating plant with bioenergy. My reason for doing this project is to look at a new business opportunity for our farm. Our company have less work during the winter time compared to the spring and this project will give us more work during the winter. I also want to take as much material as possible for heating from our farm in order to increase the value of the products from the farm. The project is in a village near us, where we should support a school, a churh, a home for the aged, a kindergarten and a parish hall with heat. In my work I have compared two different alternatives with each other. The first alternative is to put a central heater in one of the buildings, the home for the aged, in which we will burn oat.

Wastewater contains biodegradable materials, which are often measured as BOD7.Trickling filters are sometimes used as a purification step for BOD-reduction. Atrickling filter is a tower, which is filled with a carrier material. Microorganisms growon the carrier material in the form of a biofilm. This biofilm consists mostly of bacteriathat purify water from BOD.In Älgarås? wastewater treatment plant the water is purified by a trickling filter.However the treatment plant has difficulties reaching the emission requirements forBOD.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

This report describes the master thesis project ?Weight Optimization of a Composite Chassis for a Multimodal Lightweight Vehicle? which is a part of the Master program in Naval Architecture and a part of a research project at the Centre for Naval Architecture, KTH. Demands on smart and energy efficient transport solutions are continuously increasing. In the Stockholm region the citizens are expected to increase with 25% and the road vehicles with 80% until 2030, putting high demands on the traffic system. Using a small multimodal vehicle deals with this problem and uses both the land and waterways for transportation.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

The objective of this thesis was to get more knowledge about how to design a dairy farm reducing the working hours and the work tasks whit high work load. I will try to reduce the working hours and the tasks whit high work load on my own farm witch I am about inherit. Today, the old stanchion barn has room for about 60 cows and 74 young cattle and need two men to run it every day. The total acre is 188 hectare, 100 hectare forest, 65 hectare farmlands and 23 hectare natural pasture. I have studied two solutions. In the first solution, I will use my old barn for young cattle and build a new barn for the cows.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

Lerbodaälven is a river in the municipality of Kil which, due to high phosphorus content is not meeting the requirements for good ecological status according to the Water Framework Directive. The purpose of this report is to investigate the causes for the high content of phosphorus that has been measured in Lerbodaälven between 1995-2010. Four questions will be answered in this report. 1. Does the sewage treatment work affect the phosphorus level in Lerbodaälven? The result from the time series analysis shows that the sewage treatment works have a small impact on the phosphorus level in Lerbodaälven.

The City of Stockholm has decided to invest in renewable energy and especially in photovoltaics. The objective of this thesis is to investigate the photovoltaic potential on roof areas that the city possesses and to further investigate some buildings of the Property Management Department. The thesis also compares some existing photovoltaic plants with the solar irradiance map which shows available roof area on each building in Stockholm. The report ends with a literature study about the climate impact and greenhouse gas emissions of photovoltaic.The total available roof area suitable for photovoltaic plants is estimated to 700 000 m2, with a potential electricity production of 110 GWh per year. This corresponds to 17 % of the City of Stockholm?s yearly electricity consumption.

Fuel produced from renewable resources is of big interest. In this project the difference between a few different renewable materials are compared on the matter of environmental load when ethanol is produced. The renewable materials that are compared are Salix, straw and reed canary-grass (rörflen). The cellulose in the material is cut down to small pieces and then hydrolysed so that the sugar from the cellulose can be fermented into ethanol. Tha amount of ethanols that is studied in this work is the smount of ethanol needed to cultivate 1000 ha. The functional unit in the report is 1000 ha.

Both the German and the Nordic power markets are seeing dramatically changed conditions due to an ongoing process of expanding the share of renewable production in the systems. For the German part this comes from heavy subsidies which have led to an explosive development in installed capacity of photovoltaic and wind based production. After the Fukushima incident it has been decided to shut down all Germanys nuclear plants. This capacity drop is however not of the same magnitude as the increase in renewables, but will impact the stability of the power system. The Nordic power system which already has a surplus of power sees an even further increase, coming mainly from construction of new nuclear plants in Finland and a general increase in wind farms.