Rooted in Industrial Ecology (IE) theory, this report evaluates how urban agricultural concepts and techniques, can contribute to improved ecological sustainability within the inner city boundaries of Stockholm. An overarching literary study as well as an interview was carried out, resulting in a qualitative analysis followed by suggestions for practical implementations. A substantial convergence was found between the eco-restructuring objectives of IE and the principal motives for urban agriculture. Consequently, eco-restructuring objectives are found in varying degrees in the presented urban agricultural techniques. Industrial symbioses, permaculture and combinations of urban agricultural techniques are tools which are capable of corresponding adequately to the diversity of urban settings.

To enable the enhancement of the driver's environment in a forklift, an alternative form of steering has been evaluated. An earlier concept with a combined driving and steering wheel has been exchanged to a concept with two driving wheels. A link wheel has replaced the combined driving and steering wheel. The steering is done through differentiation of the velocities of the two driving wheels. The scope of this master thesis is to create a simulation model, create a control program and to evaluate the concept of two driving wheels.

ABSTRACTIntroduction: Preoperative hand disinfection aims to prevent surgical site infections. After the preparing hand wash, drying is performed using an aseptic technique. It?s important to dry hands thoroughly in order to achieve the full effect of the alcohol based hand disinfection. Due to the lack of a evidence-based guideline on this procedure, the hand drying techniques differ among operating theatre nurses, depending on which technique seen as the most appropriate.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

This thesis of 15 hp has been implemented at Halmstad University, incollaboration with Saab Dynamics in Linköping. Saab Dynamics is a companyoperating in the defence industry where competition is tough. This necessitatesnew ways to increase efficiency in the company, which is the basis for this thesis.Saab Dynamics wants to introduce simulation driven design. Since SaabDynamics engineers have little experience of simulation, required a usermethodology with clear guidelines. Due to lack of time, they chose to assign thetask to students, which resulted in this thesis.The aim of the thesis is to develop a methodology in mechanical design, wherethe designer uses the FE analysis early in the design process to develop thestructures' mechanical properties.

This thesis investigates techniques for stealth hydroacoustic communication using spread spectrum. The Swedish naval defense organisations have a vision that all their units should be able to communicate with each other, even between underwater vehicles. But the properties of water makes it a complex channel to use for wireless communications. Radiomagnetic waves have very limited range in water, therefore acoustic waves are used. In this report the basics of wireless communication systems are described including source coding, channel coding, modulation techniques as well as different techniques for spread spectrum.

This master thesis consists of the creation of shock absorber models for percussive rock drills. A model of the rock was also developed. These models were connected to existing models of the rock drill to create a complete simulation of the rock drilling process.When the models had been created the rock model was evaluated by comparison with measured values from lab tests. The verified rock model was then used to evaluate the shock absorber models.Four new shock absorber concepts have been developed. Three of these have been modelled, while the fourth have only been sketched and described.The evaluation of the models showed the following:? Simulations of the single shock absorber don?t correlate to reality very well.

This master thesis is about the production of the record ?Brutus? with the band ?Trilobit?. Trilobit consists of the three musicians, myself, Stina Hellberg Agback on pedal harp, Simon Sva?rd on guitar and Karl Jansson on drums.During the production, I have analyzed different aspects of my own musicality and also the role of the pedal harp in jazz. I have found techniques that have simplified chromatic movements on the pedal harp, and also techniques that has developed the rhythmical aspect of my improvisation.I have also looked into my process in improvising and composing and developed new aspects, many thanks to the close collaboration with Simon Sva?rd..

In this final thesis two simulation models have been integrated. The simulation models are models of JAS 39 Gripen?s fuel system, software and hardware. The time consuming and costly work to develop software has made the department of fuel system to build two models in Xmath/Systembuild. The software model also simplifies the comprehension of how the software in the control computer of the fuel system works.

The purpose of this thesis has been to build a parameterized model of a prototype motor in the program Solidworks, to use in future optimization of aspects of effectiveness and weight. The result were two models. The first model were one minor part of the whole design in 2D, to be able to optimize and study the minor part with a faster loss simulation. The second model was the whole design in 3D. The whole model were done with the three programs Solidworks, Comsol and Matlab.

The .NET Framework is a widely used system component for MicrosoftWindows. This thesis describes how the functionality of the framework canbe adapted to Microsoft Excel. Specific operations, such as integration ofuser interfaces, database connections and the ability to divide programs intosmaller components, are discussed. A number of architectural - and designpatterns to facilitate development are analysed.Several techniques have been made up in consultation with experiencedprogrammers. These techniques were further developed by implementinga number of test programs.The results of the study are a number of standard classes for future usageand a larger pilot project containing most of the analysed functionality..

This thesis discusses the possibilities to distribute digital video in a military vehicle. Today, an analogue system is used, which has a maximum capacity of eighteen video sources and the same number of monitors. The purpose of this thesis is to increase the systems capabilities regarding secure distribution and additional functions. Both software and hardware tests are made to investigate the features of the digital video standard MPEG-2. Both the coding delay and the image quality are of great interest.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.

The purpose of this literature study was to describe techniques for monitoring general anesthesia and standing chemical restraint in the horse. A number of various techniques and devices related to e.g. blood pressure measurement, blood gas analysis and pulse oximetry are defined, and finally their clinical relevance and reliability are discussed. The equine patient is generally far more exposed to anesthesia-related risks than other smaller species. Complications such as hypotension and hypercapnia are commonly seen during general anesthesia. Thus, close monitoring is essentially performed by the veterinary nurse, whom is responsible for monitoring the anesthetized patient.