n this dissertation a comparison of two evolutionary methods for evolving ANNs for robot control is made. The methods compared are SANE with enforced sub-population and delta-coding, and marker-based encoding. In an attempt to speed up evolution, marker-based encoding is extended with delta-coding. The task selected for comparison is the hunter-prey task. This task requires the robot controller to posess some form of memory as the prey can move out of sensor range.

The focus of this study is to identify important factors affect, how teachers' professional identity and role are shaped and changed during and after teacher training. Study's focus is to identify important factors bearing on how teachers' professional identity and role are shaped and changed during and after a teacher training. Respondents included in study are all teachers in vocational subject in upper secondary school. They also have experience from at practical profession before they began to work as teachers and started the teacher training. Method used in this study is the life stories of narrative nature.

The thesis demonstrates a low-cost, low-bandwidth and low-resolution Analog-to- Digital Converter(ADC) in 0.35 um CMOS Process. A second-order Sigma-Delta modulator is used as the basis of the A/D Converter. A Semi-Uniform quantizer is used with the modulator to take advantage of input distributions that are dominated by smaller-amplitude signals e.g. Audio, Voice and Image-sensor signals. A Single-bit feedback topology is used with a multi-bit quantizer in the modulator.

Det finns idag goda möjligheter att beröringsfritt kontrollera elektroniska objekt. Ett exempel är belysning som aktiveras via rörelsesensorer.Enkla lösningar innehåller oftast sensorer för ljud, ljus eller rörelse vilka används för att aktivera ett styrobjekt, vanligen genom att slå på eller av en elektronisk strömbrytare kopplad till styrobjektet. Behövs det mer säkerhet och möjlighet att bevisa för styrobjektet vem individen är som försöker få styrobjektets uppmärksamhet behövs det mer än en enkel sensor. Det behövs en anpassning för att separera olika bluetoothenheter från varandra. Bluetooth är en teknik för att trådlöst skicka information mellan två enheter.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

?Boverket? the Design Regulations in Sweden, also called BKR has for a long timebeen the mandatory standard that has guided and regulated construction design. Butat the end of 2010 BKR was replaced with Eurocode. This report deals with thecomparison of these two standards when it comes to wood construction. Duringwinter 2009/2010 there were many roof collapses due to excessive loads on theroofs across Sweden.

The purpose with this essay is to look at how categories of "us" and "them" are created, reproduced and categorised. The areas of politics and media are in focus, though they are powerful and influential actors in generating discourses.The method is qualitative analyses of current research and analyses of discourses, contexts and resources from an intersectional perspective. Intersectionality presents a theoretical tool for complex understandings of power as it takes its point of departure in an understanding of power as multidimensional and one where gender, ethnicity and class are constitutive and bearing principals. Intersectional analyses aim to understand how these dimensions are created and changed in relation to each other and how they interact with specific gender orders in specific contexts.The analyse shows that "immigrants" are in a subordinate position compared to "Swedish" when it comes to resources, contexts and discourses. The analyse indicates the relation of power between "us" and "them", where "us" have the power and with that preferential right of interpretation in discourses, contexts and resources.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

In the pulp industry, digesters are used to disolve lignin in wood chips. The concentration of lignin is measured and is called the Kappa number. In this thesis, the question of whether an online Kappa sensor, taking samples from the mid-phase of the digester, is useful or not is analyzed. For the samples to be useful, there has to be a relationship between the measured Kappa at the mid- phase and the measured Kappa in the blowpipe at the bottom of the digester. An ARX model of the lower part of the digester has been estimated.

AASS (Applied Autonomous Sensor Systems, Centrum för Tillämpade Autonoma Sensorsystem) arbetar med forskning inom autonoma system. Deras stora användningsområden är utveckling av automatiska system till fordonsindustrin samt system till äldrevården.AASS, har ett önskemål om en enklare modell av en CNC fräs för enklare fräsning till bland annat prototyptillverkning. Fokus ska ligga på kostnaden då precisionen inte är av största intresse.Uppdraget innebär att ta fram en konstruktion av en cnc- router med tre axlar med ett arbetsrum på 600x450x150mm. Maskinen ska kunna skära i mjuka material som trä, plaster men även mjukare aluminium.Resultatet är en tre axlig cnc- router som drivs av tre stycken stepmotorer som är kopplade till respektive kulskruv. Cnc routern har ett arbetsrum på cirka 600x450x150mm.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

Complete tumour regression is the optimal outcome of cancer therapies. There are however types of tumours that naturally regress. Most of these are benign, dermatological and have an early onset in life. This literature study aims to elucidate the mechanisms behind spontaneous tumour regression. In Libechov Melanoblastoma-Bearing minipigs, an animal-model specifically bred to develop malignant melanoma, the tumours usually involute within three months.

A buyer of a new car is often offered a various selection of warranties. A warranty can e.g. exist in the form of an extended new car warranty. However, some manufacturers demand that the car has to be serviced by an authorised repairer for the validity of an extended warranty. In the thesis I analyse whether such a contractual term is incompatible with today?s legislation and I argue for when such a term is to be seen as unfair.

This bachelor degree project was carried out at Saab AB Service and Repair, Arboga, Sweden. The objective was to design, construct and implement a new stable and reliable method of measuring the continuous vertical displacement (height) of the military search radar PS861 mounted on a hydraulic powered elevator. The end product needs to be durable enough to be fully operational in the harsh environment of an outdoor elevator shaft and yet as accurate and precise as possible since one of its purposes is to calibrate control equipment. Previously used technique has proven not to meet any of the above mentioned properties.A prototype using a high resolution quadrature output rotary encoder has been developed, allowing a completely digital interface. This new method has been evaluated in laboratory environment where tests have been conducted regarding both reliability and validity.