District heating covers around 80 % of the heating demand in apartment buildings and 10 % in single-family homes in Sweden. In the year 2010 the total input of energy to the Swedish district heating grids was about 70 TWh, which corresponds to 11 % of the total energy input to the whole energy system in the country. Through the combined production of heat and power the CHP-plants often reaches an efficiency of 90 % from energy in the fuel to produced heat and power. In order to keep the efficiency high it is important for the owners of the plant to have good knowledge about the plants performance at different operation points. Strängnäs Energi AB initiated this diploma work together with FVB Sverige ab in order to come up with a program for short term planning of the production of heat and power at the company´s CHP-plant.The work consists of three main parts.

As emission legislations across the world continuously pushes engine development forward,engineers constantly need to come up with and implement fuel saving technologies. During thelast decade, variable cam phasing has become a popular solution to increase gas exchangeefficiency. This configuration is typically mechanically constrained by camshaft limitations, anda solution to circumvent this problem would be to use a different valve actuation principle.One example of this is to use pressurized air controlled by electrical solenoids. Such a systemhas been developed byCargine Engineering and this provides the starting point for this work. Tobe able to operate the valvetrain on an actual engine, a control system is needed.

LevMacinstrumentet är ett analysinstrument under utveckling som utnyttjar leviterade droppar på 100 nl ? 2 ?l. Genom att använda leviterade droppar med den omgivande atmosfären som enda kontaktyta, undviker LevMac?en de vanligaste problemen associerade med miniatyrisering av analytiska tekniker, t.ex. kontaminering av provet genom desorption från provbehållaren eller andra gränsytor, adsorption av analyten till omgivningen med minskat utbyte som följd, och optisk interferens vid väggarna av provbehållaren vilket resulterar i störningar av detektionen.Tillsatser till den leviterade droppen kan göras i pl-området och reaktioner i droppen kan följas med olika spektroskopiska tekniker.

Food-poisoning is a major health problem and an estimated half a million Swedes are food-poisoned annually, with acute gastroenteritis as a consequence. One of the major causes of contaminated foods is related to food- and waterborne viruses. To be able to trace back the source of contaminant, the method of detecting viruses must be specific and sensitive. No standardized method for detecting foods for sapovirus exists today. The aim of the work described in this bachelor thesis is to implement and opti-mize a real-time RT-PCR method for the detection of all genogroups of human sapovirus in foods.

In order to optimize calf welfare and health it is important to know the behavior of cattle in free ranging conditions. When the cow is about to give birth to a calf she will leave the heard about 12 hours before. It is then rather obvious that isolating the cow about calving time in a single pen is imitating the cows? natural behavior. To save space and minimize building cost it?s common that the farmers build calving pens for four of five cows especially at larger farms.

To effectively manage a forest resource for both economic and other values good planning is required. The problem is complex since you want to know which forest to cut and when. Often a hierarchical planning structure is applied, including strategic (long-term), tactical, (medium-term) and operational level. Today SCA Forest is one of few forestry companies in the northern Sweden with an integrated forest wood supply and industry. The goals of the company are to supply their own industries with wood and to manage the resources of the forest through a long-term perspective with satisfactory profitability.

The focus of this project was to characterize the occurrence of ESBL-­?producing bacteria in two irrigation water ponds in Southern Sweden. Samples were taken from two ponds nearby each other, from which analyses were made based on levels of community and individual isolates. Community samples were used for attempts for characterization of resistance patterns in irrigation water using the Omnilog PM-­?plate system. The growth of community microbiota in the presence of the following antibiotic substances was assessed; amikacin, gentamicin, kanamycin, penicillin G, ampicillin, piperacillin, trimethoprim, potassium tellurite and ciprofloxacin. Isolates were pure cultured using semi-­?selective media: LB, Rainbow Agar, mEnterococcus, 0.1 TSA and VRBD. A total of 177 isolates were isolated randomly. Each isolate was identified using the Omnilog GENIII-­?system of biochemical characterization. Further, the isolates were tested on Brilliance ESBL-­?agar for their ability to grow. Out of the total number of isolates, 30 were selected, preferably Enterobacteriaceae or Pseudomonas spp., based on their high similarity to library strain during the identification in the Omnilog-­?system. These were further characterized using Etest-­?sticks. Three selected strains were picked for further analyses using exogenous isolation for attempts to simulate horizontal gene transfer, and Omnilog PM-­?panels containing various antibiotics of interest. Selections of samples were chosen for molecular tests targeting plasmid-­?borne resistance genes CTX-­?M1, CTX-­?M2 and SHV. The method for assessing community-­?resistance patterns showed ambiguous data that was difficult to interpret; further optimization is recommended. For all tested PM-­?plates, generally greatest differences between substances were found among wells with the strongest concentration of antibiotic substance. A total of 175 isolates displayed ability to grow on ESBL-­?agar. Etests confirmed ability of isolates to resist many ?-­?lactam antibiotics and many were clinically resistant to certain substances. No plasmids were transferred during exogenous isolation. During molecular tests, a few matches were found for the CTX-­?M1 gene. Isolates analyzed with Omnilog PM-­?plates showed resistance to most compounds tested. The isolates showed greatest resistance toward penicillin G, ampicillin, amikacin, kanamycin and trimethoprim. In the study, it was established that resistance among bacteria was frequently occurring in the irrigation water, and ?-­?lactamase producing bacteria was very common. Extended studies are needed to assess the frequency-­? and occurrence of horizontal gene transfer (HGF) in this environment. Although some potential corresponding data is found, it is at this point not possible to determine whether the resistances are due to antibiotics used in veterinary medicine, human medicine or one additional reason is travel and trade. in irrigation water using the Omnilog PM-­?plate system. The growth of community microbiota in the presence of the following antibiotic substances was assessed; amikacin, gentamicin, kanamycin, penicillin G, ampicillin, piperacillin, trimethoprim, potassium tellurite and ciprofloxacin. Isolates were pure cultured using semi-­?selective media: LB, Rainbow Agar, mEnterococcus, 0.1 TSA and VRBD. A total of 177 isolates were isolated randomly. Each isolate was identified using the Omnilog GENIII-­?system of biochemical characterization. Further, the isolates were tested on Brilliance ESBL-­?agar for their ability to grow. Out of the total number of isolates, 30 were selected, preferably Enterobacteriaceae or Pseudomonas spp., based on their high similarity to library strain during the identification in the Omnilog-­?system. These were further characterized using Etest-­?sticks. Three selected strains were picked for further analyses using exogenous isolation for attempts to simulate horizontal gene transfer, and Omnilog PM-­?panels containing various antibiotics of interest. Selections of samples were chosen for molecular tests targeting plasmid-­?borne resistance genes CTX-­?M1, CTX-­?M2 and SHV. The method for assessing community-­?resistance patterns showed ambiguous data that was difficult to interpret; further optimization is recommended. For all tested PM-­?plates, generally greatest differences between substances were found among wells with the strongest concentration of antibiotic substance. A total of 175 isolates displayed ability to grow on ESBL-­?agar. Etests confirmed ability of isolates to resist many ?-­?lactam antibiotics and many were clinically resistant to certain substances. No plasmids were transferred during exogenous isolation. During molecular tests, a few matches were found for the CTX-­?M1 gene. Isolates analyzed with Omnilog PM-­?plates showed resistance to most compounds tested. The isolates showed greatest resistance toward penicillin G, ampicillin, amikacin, kanamycin and trimethoprim. In the study, it was established that resistance among bacteria was frequently occurring in the irrigation water, and ?-­?lactamase producing bacteria was very common. Extended studies are needed to assess the frequency-­? and occurrence of horizontal gene transfer (HGF) in this environment. Although some potential corresponding data is found, it is at this point not possible to determine whether the resistances are due to antibiotics used in veterinary medicine, human medicine or one additional reason is travel and trade..

This master thesis in energy optimization was made during the autumn of 2006 at Käppala wastewater treatment plant in Lidingö, Stockholm. A preceding thesis, where all electricity consumption was mapped, showed that the aeration in the biological treatment is the single largest consumer in the plant, and it is therefore of interest to reduce this cost. The oxygen control strategy used at Käppala WWTP is working well from a nutrient removal point of view, but not from an economic one. The last aerobic zones have a very low oxygen consumption during low loading periods which give rise to enhanced dissolved oxygen concentrations with excessive costs and reduced denitrification as a result. But also during periods of normal loading unnecessary high oxygen concentration are sometimes given.By modifying the aeration control strategy three full-scale experiments have been made, with the intention to reduce the air consumption.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.

I takt med att Internetanvändandet ökar på bekostnad av andra medier blir Internet alltviktigare som marknadsföringskanal.Att synas på Internet har tidigare främst åstadkommits med hjälp av så kallade bannerannonser.Numera finns det en mängd andra sätt för att kommunicera med sina kunder somtill exempel e-postmarknadsföring och marknadsföring genom sökmotorer.Av alla varianter av marknadsföring på Internet är sökmotormarknadsföring den marknadsföringsform som växer överlägset snabbast. Det finns två varianter av sökmotormarknadsföring: vanliga annonser i form av länkar som presenteras vid sidan av sökresultatet ochsökmotoroptimering. Sökmotoroptimering, som företrädesvis behandlas i den här utredningen,syftar till att ge webbplatser höga placeringar i sökmotorer som Google, Yahoo ochMSN Search.Eftersom sökmotoroptimering, även kallat search engine optimization eller SEO, är en mycketkomplex verksamhet är det svårt för företag som vill köpa den här tjänsten att veta hur manskall gå tillväga för att få tag på en kompetent konsult. Vad som komplicerar saken ytterligareär att det har framkommit att många sökmotormarknadsförare har använt otillåtna metoder föratt ge sina kunder höga placeringar. Dessa metoder kan visserligen vara mycket effektiva menom det upptäcks riskerar både konsulten och kunden att bli utslängda ur sökmotorernasregister, även kallade index.

Sönderdelning och transport av GROT (grenar och toppar) kräver dyra maskinsystem samtidigt som efterfrågan av sortimenteten varierar kraftigt under året. Det är därför svårt att planera flöden av GROT-flis effektivt och samtidigt välja rätt maskinsystem. AB Karl Hedin är en sågverkskoncern lokaliserad i Bergslagen. De äger fyra sågverk varav tre är sverigebaserade. De levererar även GROT-flis till flertalet värmeverk och har ett behov av ett beslutsstöd som underlättar sortimentets flödesplanering och föreslår maskinsystem. Projektets syfte var att skapa ett användarvänligt enperiodsbeslutsstöd med mål att maximera den totala vinsten och genom detta kvantifiera GROT-flisflödets förbättringspotential. Nio månaders historiska flödesdata kartlades och användes som jämförande testperiod. Genom en fallstudie bestående av två scenarier analyserades optimeringar med månadsvisa, kvartalsvisa och säsongsvisa (9 mån) optimeringshorisonter: 1.

The demand for renewable energy is increasing in Sweden. This consequently increases the pressure for and willingness to pay for forest fuels. One method to extract forest fuel from suitable commercial thinnings is the "long top method? (LT-method). With this method saw logs and non-delimbed tops are recovered, i.e.

Intresset för sömlösa stålrör med stora ytterdiametrar i förhållande till tunna väggtjocklekar har ökat tillsammans med att högre hållfasthet i olika stålsorter tillkommit. Detta gör det möjligt att tillverka lättare, billigare och mer materialeffektiva stålprodukter med samma eller högre hållfasthet som tidigare.Denna nya utvecklingsriktning medför förändringar och utmaningar i en av företaget Ovakos produktionslinor i Rörverk 5 Hofors, vilket de har behov av att samarbeta med maskinkonstruktionsföretaget BEKAB för att utvärdera och utveckla.I Ovakos produktionslina i Rörverk 5 finns en del av ett asselvalsverk som kallas för "förreducerare". Denna del av asselvalsverket ser Ovako ett stort intresse i att utvärdera och utveckla för att bättre anpassas till den nya utvecklingsriktningen.  En känd utmaning hos förreduceraren sen tidigare är att den från början är framtagen för att reducera ner ett kvalitetsproblem hos rörprodukterna som kallas för trattbildning. Projektet fördjupar sig därför inom trattbildning för att bättre förstå grunden till förreducerarens nuvarande design för att därefter genomföra en redesign av förreduceraren.I en nulägesanalys av nuvarande förreducerare framkommer ett flertal olika produktionsutrustningsproblem med tillhörande kvalitetsproblem hos rörprodukterna. Projektet väljer därmed att fokusera på de produktionsutrustningsproblem som ger störst effekt för förreduceraren om de löstes.

District heating covers around 80 % of the heating demand in apartment buildings and 10 % in single-family homes in Sweden. In the year 2010 the total input of energy to the Swedish district heating grids was about 70 TWh, which corresponds to 11 % of the total energy input to the whole energy system in the country. Through the combined production of heat and power the CHP-plants often reaches an efficiency of 90 % from energy in the fuel to produced heat and power. In order to keep the efficiency high it is important for the owners of the plant to have good knowledge about the plants performance at different operation points. Strängnäs Energi AB initiated this diploma work together with FVB Sverige ab in order to come up with a program for short term planning of the production of heat and power at the company´s CHP-plant.The work consists of three main parts.

The public transport network in Täby commune consists currently of two types of bus line of whichboth belong to the category of feeder lines. The first type terminates at Danderyds sjukhus and feedsto the subway whereas the second type terminates at Täby centrum and feeds to Roslagsbanan, asuburban narrow-gauge railway system in northern Stockholm. The trunk bus line that connectsgreater parts of the commune with Danderyd is the ring line 604 and goes both clockwise (604H) andcounterclockwise (604V). The main negative aspect of this structure is the complicity in incorporatingit timetable-wise with other bus lines that share the same route, such as through Enebyberg.The goal of this project is to investigate the possibilities of splitting ring line 604 and connecting theends to two different bus routes that terminate at Täby centrum today. Apart from easing thecoordination with other bus lines through Enebyberg, the extension also creates new directconnections from various areas in Täby to Danderyds sjukhus.