Kompaktaggregat är ett integrerat FTX- och FVP-system som används i passivhus. Vi har gjortenergiberäkningar i programmet VIP+ för att se hur kompaktaggregatet skulle kunna fungera ipassivhus i Sverige.De resultat vi har fått fram ur VIP+ visar att passivhus med ett installerat kompaktaggregat klararav att nå passivhuskraven ända upp till Skellefteå. De beräknade värdena understiger kraven förpassivhus, men en viss marginal behövs för att kraven ska nås även efter uppförandet avbyggnaden. Vi har även tolkat tekniska uppgifter på ett sätt som enligt oss har en positiv effektför passivhus på kallare orter. Därför tror vi inte att värdena för de tre nordligaste platserna ärhelt tillförlitliga.

Kompaktaggregat är ett integrerat FTX- och FVP-system som används i passivhus. Vi har gjortenergiberäkningar i programmet VIP+ för att se hur kompaktaggregatet skulle kunna fungera ipassivhus i Sverige.De resultat vi har fått fram ur VIP+ visar att passivhus med ett installerat kompaktaggregat klararav att nå passivhuskraven ända upp till Skellefteå. De beräknade värdena understiger kraven förpassivhus, men en viss marginal behövs för att kraven ska nås även efter uppförandet avbyggnaden. Vi har även tolkat tekniska uppgifter på ett sätt som enligt oss har en positiv effektför passivhus på kallare orter. Därför tror vi inte att värdena för de tre nordligaste platserna ärhelt tillförlitliga.

There have been changes in Earth?s climate system on both global and regional scale since the pre-industrial era and some of these changes are due to human activities such as the combustion of fossil fuels. This calls for the development of engines with a higher efficiency and less harmful emissions. One interesting concept is the Homogeneous Charge Compression Ignition (HCCI) engine, which has the advantages of potentially low emissions combined with high efficiency. However, HCCI with diesel fuel requires a relatively long fuel/air mixing time to ensure a "homogenous" charge.

A two-factor design of experiments done on GGAB for the identification of two selected factors influence on the length of the scattering of heat exchanger gaskets. The work consists of four parts: study, choice of survey method, the performance of investigation and analysis of the results. Chosen factors on the study are considered to be the most effecting of the length distribution of seals during the production of GGAB. The study is the first of its kind both in GGAB and in the rubber industry and has an experimental nature..

This thesis was conducted at AB Fredr Wagner in Ösmo in Nynäshamn, Sweden.AB Fredr Wagner provides solutions for the graphic industry and has been asked by acustomer to develop a product that can simplify handling of EUR-pallets, namely amechanical arrangement, further called pallet exchanger that can switch from anempty pallet to a fully loaded one using only hand force.The goal with the thesis was to create design documents for a pallet exchanger, andalso from those documents to manufacture a prototype for testing and evaluation.A field trip was made to the customer, IKAB mailing in Huddinge, where the palletexchanger is thought to be placed. The purpose of this field trip was to get an insightinto the current work condition and need of change, as well as to gather informationregarding the requirements when it comes to size and robustness of the palletexchanger. Existing equipment on the market that can perform similar tasks werestudied in order to find an optimal solution for the actual pallet exchanger.After the field trip and gathering of information the concept generating phase began.The method used for generating concepts was brainstorming. To decide on whichconcept to use, a concept selection matrix was created. The selection criteriaincluded in the matrix came from the requirements for the pallet exchanger.

Vattenfall district Heating power plant in Uppsala produces district cooling with absorption heat pumps which leads to a large amount of waste heat that has to be cooled with evaporative cooling towers. The Environmental Court has ordered Vattenfall to survey the possibilities to recover the heat, which is the focus of this thesis.The study begins with an overview of the system, and conditions and limitations for waste heat recovery is examined. In the next step alternatives to recycle the heat is evaluated, either by direct recovering or by upgrading.First, the technical possibility of each alternative is discussed, and then the operation time and the amount of recovered heat is calculated. Those alternatives which are possible are brought further to an economic analysis.The cost of investment for each alternative constitutes the basis for a present value analysis. The results are put together in a table where the total amount of recovered heat is compared with the present value for the different alternatives.

People in today?s society are becoming more and more aware of how important it is to use energy as efficiently as possible. This is clearly noticeable by an increase in home produced heat with e.g. solar panels or heat pumps heating systems. These changing customer demands forces district heating technology to be redesigned, which is why there is an ongoing research regarding the next generation of district heating - low temperature district heating (LTDH).

This report describes the building of a computer model that makes it possible to simulate the thermal climate in a greenhouse. The computer model is built on the physical theory of heat exchange that occur in a greenhouse, such as radiation and convective heat exchange. The model also includes the heat storage that is active in a greenhouse.The computer model is used to simulate the thermal climate in a greenhouse under three periods, winter, spring and summer. It also investigates which effect a concrete wall has on the thermal climate in a greenhouse. The purpose of putting a concrete wall in the greenhouse model is to investigate the possibility to store heat during the day and then use this heat when the temperature drops during the night.The result from the simulations shows that a concrete wall levels the big difference in temperature that normally occurs under a day in a greenhouse.

Modern technology and fast development of heat pumps, the hunt for savings in energy consumption and the strive for environmentally friendly energy sources, convenience, and financial profit, have made heat pumps a reasonable alternative for the heating of houses.When the heat pump starts it will consume a considerable amount of current, which may result in a short-lived voltage-drop if the power grid is weak compared to the start-up current.The company Fortum Distribution which owns and administrates electrical network is interested in an investigation that deals with heat pumps affect on the quality of electricity.The purpose of this investigation is to study fast electrical fluctuations (flicker) as a result of start-up currents for single as well as multiple heat pumps on the same electrical station and from this evaluate whether there will be any problems installing heat pumps..

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

The aim of this thesis was to investigate if the robotized welding method FSW (Friction Stir Welding) could be applied for joining a rotating structure in an aero engine at Volvo Aero Corporation. FSW is expected to introduce less defects than today?s welding methods and could therefore be suitable for critical aero components. The material is the nickel based alloy Inconel 718, however a material experimentation is outside the scope of this report.The main goal of this study is to verify if the ESAB ROSIO robot based FSW-system has a suitable work space to be able to weld the rotating structure, and if the welding tool has accessibility to the joints. The FSW-process needs a rigid fixture, and a number of fix-ture concepts are presented based on a proposed weld sequence.

When a combined heat and power plant produces heat and power it often faces a deficit of heat load during the summer or other periods of time. This heat is often unnecessarily cooled away or the power production has to be reduced or shut off. If it is possible to store heat from periods with low heat demand to periods with high heat demand one can get many benefits. Among these benefits are: increased power production, decreased operation with partial load, uniformly distributed load.To be able to store heat in situations like this long-term thermal heat storages are needed. In this thesis five different types of stores are presented: rock cavern storage, tank storage, pit water storage, borehole storage and aquifer storage.

This diploma work covers an investigation over the heat - and hot water systems of thetenant-owner's association, Bogården. The heat - and hot water needs of Bogården aresatisfied by both district heating as well as three heat pumps. Implemented investigationshows that the heat pumps are not used in a profitable way. Apart from that, the reservepossibilities are small. There is also a risk of the growth of Legionella bacterium in thehot water system.Since the heat pumps are already installed, HSB-Gävleborg (responsible for Bogården)has a wish to investigate possible proposed actions for optimization of existing plant.After completed investigation, a new proposed action is presented.

Cooling down the indoor air can be done in several ways. One way is desiccantcooling which will be used at the Stockholm Arena. This method is used in airhandling units that use temperature changes and moisture fluctuations in the air. Oneof the steps is to add heat during the cooling process in order to reduce the relativehumidity of the exhaust air. The air passes thru an adsorptions rotor which thenabsorbs moisture from the supply air.

För att ha en chans att ändra trenden med ökande utsläpp av växthusgaser är internationella samarbeten nödvändiga. Därför har EU genom miljökvalitetsmålet Begränsad Miljöpåverkan satt krav på högsta tillåtna utsläpp av växthusgaser. Att sänka energianvändningen för upp- värmning är ett steg i att även sänka utsläpp av koldioxid, som är en av växthusgaserna. Sänkning av energianvändning kan göras på flera sätt, bl.a. genom att öka tjockleken på isoleringen eller återvinna värmen i frånluften. Men dessa åtgärder ska inte helt okritiskt göras.