Wind is used as an energy source all over the world. To be able to use this effectively, there is a need for as good forecasts and forecast models as possible. One of these models is Coupled Ocean/Atmosphere Mesoscale Prediction System (COAMPS®) that is used to calculate short time forecasts. This model is used here to calculate wind speeds at two different areas in Västra Götaland, Bengtsfors and Vänersborg. There are also wind measurements with SODAR stations for these areas.

This master thesis was a subtask of a project called EMIR-1. The goal with the thesis was tobuild a system for particulate mass measurements in one of the engine test cells at KTH. Theparticulate mass measurements are planned to be measured with a TEOM.The exhaust gases must first be diluted with air before the sample is sent to the TEOM.Therefore an ejector diluter for this matter also was designed and evaluated in the thesis.Emissions measurements have been done both with and without dilution to determine thedilution ratio. Tests have been done for different speeds and loads.Problems with stability of the dilution ratio have been an issue throughout the process andpressure pulsations in the exhaust pipe are believed to be the cause. More tests have to be done tomake sure that this is the problem.One idea is to make the inner diameter of the diluter nozzle smaller and see if it changes thedilution ratio stability.

AbstractThe Swedish Road Administration in the region of Mälardalen has since 2004 worked to in¬crease the efficiency of the maintance of bridges based on limited functional requirements and time demanded action.The maintenance of the bridges is contracted in the county of Uppsala since 2004, and Örebro since 2007. The county of Nyköping and Västerås is contracted by the traditional system. The contractor will perform a regular maintenance on all bridges. The bridges are inspected by the contractor at least once every year.The contractor registers the result of the inspection in a database called BaTMan. BaTMan is a Bridge and Tunnel Management system and is a strictly web solution were the user logs in via the internet.The Swedish Road Administration also inspects the bridges to se that the demands on the bridges are followed.My work is to compare these different inspections and to see any development..

In 1997, the Swedish parliament adopted a decision on Vision Zero (nollvision) in the road and transport system. Vision Zero means that no one should be killed or seriously injured in traffic accidents in the road transport system (Prop. 2003/04: 160). For the Transport Administration in Sweden (Trafikverket), this means increased demands on security and signage at road work sites around the country. This in turn means increased demands on the contractors that carry out road work for the Transport Administration.

Bachelor thesis, Business Administration and Economics Programme, School of Business and Economics at Linnaeus University in Va?xjo?.Spring of 2015 Title: Performance measurement from a cost leadership perspective - A case study on Gekås.Authors: Adrienn Csiszer, Hannah Lundberg & Helena WennerströmTutor: Eva GustavssonExaminer: Karin Jonnergård Keywords: Performance measurement, Performance measurement systems, Generic strategy, Cost leadership strategy, Financial and non-financial measurements. Purpose: The purpose of this study is to examine how a company with a clear cost leadership strategy chooses to work with performance measurements, with a view to comparing a practical example to theorethical approaches. Methodology: The method chosen for this paper is a case study on Gekås AB. The presented data were collected through interviews conducted with four employees on Gekås. Conclusion: The study concludes that for a business with cost leadership strategy the financial measurements are more important than non-financial meausurements. For Gekås it is important to keep the performance measurement simple and understandable for the employees. They only use three measurements (sales, hours and sales per hour) in planning and in evaluation.

The purpose of the present study was to study if the systemic blood pressure in cats significant increases due to stress associated with a visit to a veterinarian clinic. We also wanted to investigate the clinical utility of two different methods for indirect blood pressure measurements in cats by assessing how easy they were to use and how reliable measurements they provided. The methods that were used were oscillometric (Memo Diagnostic) and ultrasound-doppler technique (Minidop). The blood pressure was measured in both clinical environment and home environment. Fifty cats were used in the study, from which measurements were impossible to obtain in one cat.

As trucks are getting more and more advanced, information about their weight has become a key factor for controlling them in a more fuel efficient and safe manner. Knowing the mass of a heavy duty vehicle in real time has been a difficult challenge for the truck manufacturers. With the processing power for electronic control units in trucks steadily increasing, more advanced algorithms for calculating the mass has been developed, but at the moment there still is a wish for better performance.Since there is a lack of good information regarding the external forces acting on the vehicle, forces that depends on the slope of the road, foundation of the road and the wind, the methods have to be able to disregard these. Such an approach, based on an indirect least square solution, has been evaluated in this thesis. The results have been promising and based on these a recommendation about further evaluation has been made..

The purpose of this study was to develop recommendations for using more efficient lighting and better graphic design to create a more uniform structure in the exhibition hall ?Road to the past? in Jönköping County Museum by answering the following questions at issue:1) How are the objects in the exhibition hall ?Road to the past? exposed today?2) How can you use lighting and graphic design to create structure in the exhibition and strengthen the expression in the exhibition?Our work is based on observations and open group interviews. We observed the exhibition hall ?Road to the past? during day and evening. In the same hall, we observed a guided tour that we followed up with open group interviews.

This report describes an investigation of the indoor climate in two different workspaces. Since we a big part of our lives are staying indoors in artificial environments, and more particularly in our workplaces, we think it would be interesting to do this investigation. The technical solutions for air treatment systems began with simple natural systems without fans and where the thermal rise of the air applied. In modern time is technical air treating systems used to take care of the fresh air supply. This type of units can supply filtered air with the right temperature to the building. Well-functioning ventilation is essential to bring clean fresh air to the room and effectively remove impurities without sound- or draught problems. The indoor climate is relevant for the output capacity.

Stockholm city has recently raised its ambitions for bicycle traffic, the goal is to achieve a larger andsafer bicycle traffic. But cyclists are more vulnerable on the roads than other vehicle users because of the lack of protection. This means that a large proportion of road safety for cyclists is based on the design of the traffic environment. Since most serious bicycle accidents are those that occur in conflict with motor vehicles, and the majority of these accidents occur at intersections, these areas are of great importance forcyclist?s safety.The  purpose  of  this  paper  is  to  highlight  bicycle  accidents  at  intersections  and  to  suggest improvements  in three accident-prone junctions  in Stockholm.  This is  achieved  by  the study of accident statistics, literature and finally three case studies.The literature study focused on cyclists, traffic safety and traffic safety measures.

This report treats a Master Thesis performed at Scania CV AB. The task was to create a computer model of a hydraulic actuator system in the software AVL Hydsim. The system consists of two spring-loaded masses with surrounding hydraulic components. The purpose of the model is to study phenomenon and problems in the system, as well as to be a support in the development of the system. It is not supposed to be used to study absolute values in its current form.

Stockholm city has recently raised its ambitions for bicycle traffic, the goal is to achieve a larger andsafer bicycle traffic. But cyclists are more vulnerable on the roads than other vehicle users because of the lack of protection. This means that a large proportion of road safety for cyclists is based on the design of the traffic environment. Since most serious bicycle accidents are those that occur in conflict with motor vehicles, and the majority of these accidents occur at intersections, these areas are of great importance forcyclist?s safety.The  purpose  of  this  paper  is  to  highlight  bicycle  accidents  at  intersections  and  to  suggest improvements  in three accident-prone junctions  in Stockholm.  This is  achieved  by  the study of accident statistics, literature and finally three case studies.The literature study focused on cyclists, traffic safety and traffic safety measures.

The study was carried out as a time study of five wood chippers placed on trucks,so?called huggbilar. They are trucks with built?in wood chipper, chip bowl and crane pulling a chip trailer. The system is used for chipping wood fuel, transporting, and delivering the chips to heating plants.

se PDF.

Single vehicle accidents are one of the most common types of accidents that occur on the Swedish road network. Depending on the design of the road, the presence of a crash barrier and embankment on the roadside, the outcome of a roadside collision can lead to serious injuries and even deaths.The aim of this project is to investigate the possibility of improving road safety by designing the optimal roadside area based on the results of a life cycle cost analysis (LCC).The questions that have been answered during the duration of this project are:1) Describe the current technical solutions for roadside area design and the various barrier types used in Sweden.2) Complete an existing mathematical model that has been developed by Hawzheen Karim, for calculating life-cycle costs for various roadside areas.3) Calculate and compare the life cycle costs for the side area with a barrier and without a barrier.By performing an analysis of the documentation on the current guidelines and rules for shaping the roadside, was it possible to describe the current technical solutions for the formation the roadside as well as the current roadside barriers in use today. A mathematical model for calculating the life cycle costs of different barrier types had already been developed by Hawzheen Karim. This model was supplemented so that it could calculate life-cycle costs of the roadside region with and without a barrier. After the model was completed, an analysis was performed to obtain life-cycle costs of a roadside with and without a barrier.The result showed that there is a clear relationship between the slope inclination, fill height, and the rate at which the costs rise.