In this project forging of aluminum alloy Al 6026 T9 has been performed in the temperature range of 400 °C ? 470 °C. The alloy which was in the shape of a cylindrical billet was formed in a press with the aim of analyzing the effect of different forging temperatures and required press load for optimal die filling. The component?s dimensions were later measured and compared to a reference piece.

There are many different recommendations on how to keep pelargoniums over winter, but most of the recommendations suggest ?the higher the temperature, the more light and water the pelargonium needs?. The purpose with this paper is to try to explain the best and the worst results that are achieved with different storage alternatives of zonal pelargoniums. The results are based on an orientating investigation carried out in January-February, and a questionnaire that members of the Swedish Pelargonium Society answered to. Both the orientating investigation and the questionnaire showed that zonal pelargoniums are best stored light and cold but frost free. They should be irrigated according to their needs which is when the soil is dry, about every second to third week. Zonal pelargoniums are very resistant to drought and can survive without water for at least 44 days, both when kept under light and cold as well as under light and warm.

Today, there are no regulations saying that cows must have access to some kind of shelter at pasture during the summer. In more tropical countries, it is well-known that dairy cows might suffer from heat stress when exposed to sun and high temperatures. The well-being of the cows is thereby reduced and the production may also decrease. In Sweden, no research has been done in the area and therefore it is now a clear need of improved knowledge.The purpose of this study was to investigate the importance of shade for dairy cows in Sweden. The behaviour of 30 cows was examined to see any differences between cows with access to shade and cows without access to shade.

In this report you can get a complete instruction about how to build your own development system for the PIC-processor. This card will be used for laborations for the students at LITH-ITN. With this card you can send new assembler codes (new instructions) down to the microprocessor via the Serialport on your computer. Then the new instructions for the microprocessor will start to execute. We made a solder paste stencil at Campus Norrköping solder paste stencil laboratory.

The automotive market is currently undergoing a historical change where stricter emission legislations and ever increasing fuel costs have intensified the search for effective alternatives to the conventional internal combustion engine, which has resulted in a substantial trend towards electrification of powertrains. Storage of electrical energy is the fundamental component in this technology where the lithium-ion batteries are currently considered as the most appropriate solution. Lithium-ion batteries, however, as other types of batteries, can only be used efficiently and durably within a specific temperature range.This Master thesis has been carried out in collaboration with Electroengine in Sweden AB, situated in Uppsala, which has an ongoing project regarding development of a modular battery system for electric powertrains. The project is at a stage where an initial prototype has been developed which provides the foundation for this thesis. The study has addressed the battery system performance from a thermal perspective, in order to validate the ability of the system to create a thermally serviceable environment for the lithium-ion battery cells.

In this study, the effects of using fine milled cassava stems as an additive in biofuel pellet production was compared to the effects of refined starch addition. The bulk biomass fuel raw material, to which the additive was added, was a blend of spruce and pine sawdust. An experimental design in the factors cassava/starch content, moisture content and material temperature was used. Measured responses were pellet bulk density, pellet durability, amount of fines, pelletizer motor current, pellet temperature, die temperature and CV for pelletizer motor current (a measure of process stability). Each response was modeled by multiple linear regression (MLR).

Safe retrieval of nutrients from human excreta to fertilize crops in order to gain adequate yields will increase food security and sustainability in agriculture areas with nutrient-poor fields. Safe and nutritious food will meet the dietary needs of the individual which promotes public health and the ability of an active life. Human excreta should be considered as a resource instead of being assumed as waste. Human faeces and urine is excellent fertilizers which may close the nutrient loop if utilized properly. However, sanitation of the excreta is required to prevent disease transmission by reducing the content of gastrointestinal pathogens such as bacteria, viruses and parasites. The objective of this study was to in small scale evaluate the sanitation in a combined liquid compost and urea treatment by monitor the inactivation of bacteria and viruses at the combination three start temperatures, 45, 40 and 35 °C, and three additions of urea, 0.5, 0.75 and 1 % and reference, 0 % urea addition.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Trädgårdens hantverk och design, 15 hp, 2015.

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

This report is the written documentation of a project work carried out at the Division of Engineering Materials at Luleå University of Technology in cooperation with Seco Tools AB. The project deals with the analysis of residual stresses in Ti-Al-N thin film grown on WC/Co cutting inserts. The composition of Al varied from 0% up to 75%. Increasing the Al content in the Ti(1-x)Alx N compound improves the compressive residual stresses even after annealing of the material. The experiments have been performed in a high temperature x-ray diffractometer (HTXRD) where the interplanar atomic spacing was determined in-situ and subsequent converted into stresses.

The aim of this study was to increase the knowledge about whooper swan (Cygnus cygnus) ecology to enhance the ability to predict and also to prevent the crop damage they cause. The largest proportion of damage in Sweden has been reported at stopover sites during spring migration in February, March and April. Therefore, this study focused on an important stopover site, Lake Tysslingen, situated in south-central Sweden. Specifically, the relation between the duration and period migrating swans stage at the stopover site and mean temperature (measured at three different weather stations) for the years 2001-2010 was studied. Furthermore, the swans´ selection for certain fields in relation to field type, distance to roosting site, a supplemental feeding site and forest edge within agricultural land surrounding the lake was analyzed.

The aim of this study was to increase the knowledge about whooper swan (Cygnus cygnus) ecology to enhance the ability to predict and also to prevent the crop damage they cause. The largest proportion of damage in Sweden has been reported at stopover sites during spring migration in February, March and April. Therefore, this study focused on an important stopover site, Lake Tysslingen, situated in south-central Sweden. Specifically, the relation between the duration and period migrating swans stage at the stopover site and mean temperature (measured at three different weather stations) for the years 2001-2010 was studied. Furthermore, the swans´ selection for certain fields in relation to field type, distance to roosting site, a supplemental feeding site and forest edge within agricultural land surrounding the lake was analyzed.

ABSTRACT: Commercial swab transport systems are used for collection and transporting of fecal and other microbiological samples. This system must maintain viability and contribute to survival of microorganisms during transport to the laboratory. Four swab transport systems have been compared, eSwab, ?- Transwab and fecalSwab, all three with flocked swabs, and Copan Venturi Transystem with rayon swabs. The study followed the recommendations from the Clinical Laboratory Standard Institute; document M40-A for recovery of Samonella, Shigella, Yersinia and Neisseria gonorrhoeae after storage for 0, 6, 24, 48 and 72 h at room- (22-25°C) and refrigerated (2-8ºC) temperature.

The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.

ABSTRACT: Commercial swab transport systems are used for collection and transporting of fecal and other microbiological samples. This system must maintain viability and contribute to survival of microorganisms during transport to the laboratory. Four swab transport systems have been compared, eSwab, ?- Transwab and fecalSwab, all three with flocked swabs, and Copan Venturi Transystem with rayon swabs. The study followed the recommendations from the Clinical Laboratory Standard Institute; document M40-A for recovery of Samonella, Shigella, Yersinia and Neisseria gonorrhoeae after storage for 0, 6, 24, 48 and 72 h at room- (22-25°C) and refrigerated (2-8ºC) temperature.