The purpose of the present study was to examine effects of driver, vehicle, and environment characteristics on Collision Warning System (CWS) design. One hypothesis was made that the capability of collision avoidance would not be same among a driver, vehicle, and environment group with different characteristics. Accident analysis and quantitative analysis was used to examine this hypothesis in terms of ?risk? and ?safety margin? respectively. Rear-end collision had a stronger focus in the present study.

SEP Modular Armoured Tactical System is the next generation of military vehicles developedby BAE Systems Hägglunds AB. At present time, BAE Systems Hägglunds AB aredeveloping a 6-wheel electrical hybrid and a conventional 8-wheel vehicle. The questionformulation was summarized as: ?In which ways can the electrical transmission in a hybriddriveline for SEP be designed, when the surrounding fixed interfaces are kept and the unity ofcomponents within SEP is maximized??. The purpose of this master thesis was to study avariety of concepts for hybrid propulsion.

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

This report covers the conceptual design of a new one person hybrid vehicle that is to be fast and convenient to drive on the roads. The vehicle is most of all supposed to be used as a commute vehicle but can also be used at other occasions as well.During the work with this project the group has focused on three larger areas, the outer design (body), wheel chassis and an ergonomically designed interior. The group was not able to just create these parts in 3D to get a trustworthy vehicle, hence number of other components and details were also created to get a better entirety.The outer design starts with idea generation and sketches and ends with a 3D model which is rendered to show how the final product is going to look. The design of the body has been going on during the entire work process due to new ideas and improvements that seemed interesting and had to be changed.The wheel chassis also started with idea generation, research and sketches. It ended up with a simulated 3D model which later on was mounted on the vehicle body to show how the vehicle is going to perform during usage.

This master thesis is performed at Scania Axles and Gearboxes, a production plant located in Södertälje. Within the plant axles, gearboxes as well as central gears are assembled from components to finished products. All production is conducted on production lines, with a pre-determined rate, which is supplied with components by the material handling department. Since the production quantity and the mix of product variants produced on the production line is customer order-based, the number and type of components needed for production as well as appropriate staffing within the material handling department is difficult to predict. Scania is currently using a number of different resource planning tools for each material handling-department within Axles and Gearboxes to visualize the workload within the departments.

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

In order to avoid harmful substances ending up at the municipal sewage treatment plants, it is important to purify the wastewater at the source. One such source is the wheel washers available in many tire garages which are used to wash the wheels on our vehicles when we change between summer and winter tires. It is important to wash the wheels before storage, to extend the tires lifetime. The purpose of this study is to find a green innovative solution for reduction of emissions of heavy metals at the source, so that the sludge from the sewage treatment plants can be used as fertilizer. The target is to find a wheel wash method which leads to compliance with the guidelines for car washers, and that also provides a better washing result than with the existing method.

This report reflects an examination work performed for Getrag All Wheel Drive AB during the spring of 2005. Among the companies range of products there exists some concern regarding the amount of clamping force and friction on bolted joints caused by the assembly torque.The aim of this project has been to determine if there is a simple way in which to identify and then practically apply testing methods for clamping force and friction through utilization of existing testing equipment.Three separate methods of clamping force and friction determination have been tested in rear drive unit, RDU, at a 30 Nm assembly torque. A fourth and final method, screw elongation with ultrasound, has been used as reference. The methods are:?Torque-Tension test.?Screw elongation with micrometer.?Joint stiffness test.?Screw elongation with ultra sound for reference.The results from tests can be viewed in table below.MethodTorque-TensionMicrometerCs=318 kN/mm Assembled with torque wrenchMicrometerCs=318 kN/mm Assembled on lineUltra-soundCS=311 kN/mm Ultra- soundCS=318 kN/mm Joint stiffnessTheoreticalClamping force-21,8 kN17,6 kN17,3 kN17,6 kN17,1 kN17,3 kNFriction-0,110,1470,1530,1470,1520,149.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

The Swedish Military Defence is about to make a large reorganization. Surplus, everything from tanks to personal underwear, enough to equip 800,000 soldiers will be destroyed or sold to the highest bidder. This thesis is a discourse analysis about the argumentation in media between the Military and the enthusiast, who are interested in military vehicles and military surplus..

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

The object of the thesis is to propose a new design for the neighbourhood of Veiberg that is situated in the small Norwegian town Jessheim. My approach was to first make an analysis of the whole community and the structure of the town, and then gradually focus on the actual neighbourhood to continue the research there. On the basis of my research the block will be redesigned. The research will lead to a well-planned design of the neighbourhood, which will adapt it to its surroundings in a sustainable and constructive way. The project will lead you through the history of the town and the intentions and aims of the municipality. The project also examines the structure of the town and the function of the neighbourhood in the town today as well as investigation of the history, the structure and the qualities in the area.