This thesis studies the concept of balance in the management control systems (MCS) of a small Swedish company within the IT-sector. The aim is to evaluate the importance of balance and dynamics in MCS and investigate which factors affect them. The frameworks used are Simons (1994) four levers of control, and the five-factor model for balance and dynamics by Mundy (2010). The small IT company - the object of the case study - has grown extensively in the last years and needs to develop more formal MCS without losing efficiency and creativity in their fast-moving industry. The case study reveals that balancing MCS is important also in smaller companies with less formal MCS.

Chinas government has a multifunctional program for a more sustainable forestry since 2000. This six key forest programs goal is to develop a more sustainable forest sector but also take environment consideration. The state forest administration in China has decided to create 5.8 million hectare of fast growing and high yield forest. Eucalyptus has showed to have good properties for pulp and timber production and therefore Eucalyptus plantations are under development in costal areas in southern China. By adding extra nutrients, growth can be enhanced in Eucalyptus plantations.

Studiens syfte var att undersöka om det fanns skillnader i personlighet och val av konfliktstil beroende av vilken placering respondenterna hade i syskonskaran samt om Locus of control skiljde sig mellan olika åldersgrupper. Samband mellan chefers konfliktstil och personlighet undersöktes också. De 103 respondenterna som var mellan 25-75 år, 63% män och 37% kvinnor, besvarade en enkät som bestod av demografiska frågoroch arbetsrelaterade frågor om chefskap. Tre test användes; ett personlighetstest, RottersLocus of Control och Thomas-Kihlman?s konfliktstiltest.

AbstractThe purpose with this study was to get knowledge if there are any possible differences in, and correlation between, experienced stress, experienced demands, experienced control and experienced social support in correlation to shiftwork.The study was made at two central hospitals in south of Sweden and had 90 participants (78 women and 12 men) that answered a questionnaire in the current variables. The result in experienced stress showed that there were no differences between shift workers. The results showed a difference between the day- and the nightshift in the correlation between control and stress. The writers speculates that the reason why the nightshift experience high stressvalues with high control can depend on the lack of presence by higher managers, compared with the dayshift. .

The purpose of the Sharing Economy is to exploit unused resources between people, as an alternative to buying new and owning themselves (Gansky, 2010). Gansky (2010) argues that a major reason why the Sharing Economy has grown in recent times is, besides from the recession and people?s increased environmental awareness, the urbanization which has made people move closer to each other and in to the big cities. This in addition to an increased use of GPS technology in smartphones enables people to be constantly connected to an ever-changing network. People now share and exchange services and products from each other.

In this bachelor thesis, diagnostic methods for one of Siemens stem inlet control valves have been developed. The work has taken place during ten weeks at Siemens Industrial Turbomachinery AB in Finspång. The company produce steam- and gas turbines and also provides service and maintenance. The purpose with this project has been to develop diagnostic methods that oversee the health of the control valves. By using the developed methods you will know when it?s time for maintenance.

Background: Performance measurement as a management control tool has received considerable academic attention. As the number of inter-organisational relationships, such as customer-supplier relationships, increases, there is a new scope for performance measurement as a management control tool. In order for a company to assess the effectiveness of its supplier relationships it has to define, measure and evaluate variables that are critical for the success of the relationship. The role of management control, and thereby of performance measurement, has increasingly been discussed in theory. However, empirical research in this area is still somewhat limited.

Background: The population of the world is getting older and in the year of 2020, 1.2 billion people will be 60 years or older. A common health complaint affecting the quality of life in elderly persons are sleep difficulties. Physical activity is claimed to improve sleep quality and the maintenance of a normal circadian rhythm. Several studies have shown positive effects of physical activity on sleep quality, still the evidence of physical activity as sleep-promoter is insufficient. Aim: The aim of this study was to investigate associations between physical activities and sleep quality in persons ?60 years of age.

Ever since ABB has begun diecasting their rotors instead of permanent mold casting it,variation in the quality of the cast has arisen. Diecasting is performed in three differentmachines, M1, M2, M3 with 400, 660 respectively 800 tons of die locking pressures.The aim of this thesis is to answer the following questions:What is the ?right? cast quality? How is the right quality achieved?For sizes 160-180 solutions will be proposed that consider eccentricity between thelaminate and the short circuit ring as well as elimination of the thin Al film that appearson the outer periphery of the rotors.Through considering the statistic material the most often diverging rotor type has beenidentified and one of the actual rotors has been sent to a laboratory to be analyzed inorder to establish the current defects. The result of the analysis shows that there areplenty of gas- and oxide-porosity.It has been proved that every time the dies temperature decreased below 120°C thecontent of gas porosity increased. It is due to rapid solidification of metal that flowsthrough the ?cold? laminate.It has confirmed that enhanced porosity in squirrel cage causes high impedance in therotors.

The implementation of a material requirements planning system is a complex and demanding task. There has been much research into what factors are important in such implementations, but seemingly very little about the links between critical success factors and management control systems. This thesis attempts, through a case study, to answer the question of how management control systems affect the implementation of an MRP system in ASSA AB, a Swedish manufacturing firm. Data is primarily collected through interviews. Theory regarding implementation success definitions, critical success factors as well as management control systems is presented.

The aim of this Master?s thesis is to study the effects that geographical distance have on the control systems in a scattered organization and how this, ultimately, affects the employees in terms of loyalty and motivation. In order to do this, a case study has been conducted on a multinational travel group and its local branches in Thailand. The study is based on a selected number of theories focusing mainly on control systems in multinational contexts as well as on theories regarding communication and autonomy. The conclusion of the study is that geographical distance has led to a rather large autonomy for the local branches and that the headquarter to a large extent rely more on formal control.

Quality is the key to a well executed product or service. The construction industry hasn?t highlighted the quality in recent times which have contributed to the construction industry receiving much criticism in the field. The public sees it as an offhanded industry where errors and delays are common.The reason for this is considered to be primarily the lack of time, constant pressure to reduce costs and skills and the ability to communicate between the parties about what the correct quality really means. The industry has begun to realize that it must start setting clearer standards and that there are great opportunities for improvement.This report will give Peab an opportunity to develop their quality work.

Recent years have been very turbulent for most private equity firms. Especially the financial meltdown in global economy has affected the industry, but also the public pressure has made private equity houses change their control strategies towards more conventional methods used in public companies. This thesis aims to put light on the control methods used in listed private equity houses which use a buyout strategy. The paper describes how the control methods change over the different phases the asset experience and how different value generating strategies use altered control methods. Using Merchant's (2003) framework for management control systems and Berg and Gottschalg's (2004) research on value generating strategies in buyouts the thesis shows that action controls as designing instructions for the board and a business plan, together with goal alignment is the commonly used control strategy directly after the acquisition.

In this master thesis, control algoritms using arm side sensors are investigated for an industrial robot. The sensors can be position encoders placed after the gearbox and accelerometers on the robot arms. Control strategies are discussed and evaluated for different models of the robot, after which chosen strategies are applied to a realistic model. Control algoritms using arm side sensors (LQ, dual-loop and PD-PID) are compared to a PID-controller that only uses measurements of motor position for feedback control. The comparison are done with respect to disturbance rejection, oscillation damping, robustness and tracking performance of a reference trajectory.

Preporsition for bachelor thesis project, working from the inside and out. Emphasising spatial quality and experience, More or less ignoring form and program. I?ve had issues with these aspects in earlier project, the form or the program takes alot of place in the project. I haven?t tried this approach before, it?s an attractive thought to allow the project take a form of it?s own, enclosing those spaces i create.The initial concept was to place the pools on the ground (not digging them into the ground) making them volumes that divide and define spaces.