The sound part is mainly practical and is dependent on concepts that have been tested through measuring with a sound level meter. The design part is more theoretical and has been verified with CAD models and finite element analysis.With a sound damping hood on the compressor the sound level is reduced with up to four dB. An optimized absorbent for the compressor space gives a reduction with three dB. By using the insulation for the heat water tank as absorbent we can see a sound reduction on the lover octave bands. A reduction like this is elsewhere hard to achieve as at it requires thick absorbents.By changing the today?s insulation to the heat water tank to a form of polystyrene polymer insulation the weight from the heat pump above can be transferred to the stable heat water tank.

In modern society in terms of economics and environmental impact, it is important to ensure that a company is as energy efficient as possible to reduce the amount of energy used. About 10 TWh of electricity used annually to pump drives in Swedish industry. Therefore, pumping system has great potential for energy savings.The objective of this report was to determine how much energy and money that can be saved with the insertion of variable speed drive to six pumps on Bleach plant 4 in Skutskär Mill. The work was performed with electrical measurements during one week, analysis of pump curves and the compilation of production data over a year.The results show that four of these six pumps were profitable and yielded an annual saving of 1172 MWh of electricity and 560 000 SEK. With an economic lifetime of 10 years and a discount rate of 6.8% the final result for the entire life-cycle savings became 3 355 000 SEK.

This master thesis is an in-depth study of an existing heating system at a household cooperative in Uppsala that has been converted from district heating to a bedrock heat pump system. The study focuses on an economical system optimisation of the building?s complete heating system. The aim was to determine how well a heat pump system in large buildings actually work, find out possible ways to optimize the existing system and point out important system parameters for new heat pump installations in larger buildings.The project points out a possible energy cost reduction of 45 % without investment and further cost reductions with equipment investments. A reduction by 30 % is possible by improvements in the regulation system and 15 % is possible by maintaining the brine system.

The study aims to give a description of the conditions in which matters is prepared withinSwedish Government`s offices, to describe the adaptive capacity in the agency`s internalprocesses by investigating the experiences of some civil servants restricted to the Ministry ofEnterprise and the Ministry of Environment in their work with the EU Maritime Policy GreenPaper. The results have been analyzed against the basis of eight identified criteria of buildingadaptive capacity in socially dominated systems. The criteria are comprised of both individualand organizational abilities. Only two of them were fully met; the criteria about diversity inexperiences and knowledge and the criteria about information and how the information hasbeen applied. However, the process has traces of all the identified criteria.

Glulam is a product that was engineered to make use of timber in a more efficient way. Bychoosing timber of similar quality and discarding natural defects during production, thedevelopment of a stronger cross-section is achieved.Carbon fiber is a relatively new material with a high tension capacity. This feature is used toexamine how the bending capacity of the beams improve by adhering carbon fiber laminateson the lower edge of the beamsThe strength of the material is tested with three experiments: carbon fiber on the bottom of thebeam (a), carbon fiber attached to the lower sides of the beam (b) and carbon fiber in thebeam, covered with a layer of wood (c)The results show that the first case, where the carbon fiber is attached to the bottom of thebeam, gave the best result with an increase in capacity of 59 % compared to the nonreinforcedcontrol. The other two cases also show an improvement in capacity, beam-type 3had a capacity increase of 47% and beam-type 4 increased with 25 %Tests were also made with glulam beams reinforced with fiberglass, but these tests were notanalyzed in depth because the purpose was to compare the capacity to carbon fiber. Thisbeam improved its capacity by 40.3%.The tests show that carbon fiber as a reinforcement material for glulam is a good choice whenthere is a requirement for stronger cross-sections in both new production and renovation ofold buildings.

För att transportera bränsle från tanken till motorn används på tunga fordon idag vanligen en mekanisk pump, driven av och placerad på motorn. Anledningen till att ha en direktdriven pump är främst att det anses som den mest robusta lösningen för den relativt enkla uppgiften som bränsletransport och liten tryckökning anses vara. För att klara av motorstart och driftsfall med höga bränsleflöden är dagens pump överdimensionerad för det behov som finns större delen av tiden.Önskvärt vore att kunna reglera bränslemängden kontinuerligt, för att minska pumparbetet i de punkter matarpumpen idag har överkapacitet. En elektrisk pump kan regleras att endast pumpa bränsle efter behov och erbjuder även andra fördelar, som t.ex. fri placering, möjlighet att använda en mindre pump och tilläggsfunktioner genom mjukvara, exempelvis priming och automatisk avluftning.Projektet har genomförts i form av en förstudie med konceptgenerering för placering av komponenter och provning av dagens system för kravspecifikation.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

In modern military operations the requirements of transmitting large amounts of information have increased substantially during the last decade. This increases the demand for high-capacity radio networks. It is also very important that military decisions are made on recent and correct information and this implies that low and known delays are required. The existing military radio ommunications, within the Swedish army, do not meet the requirements for capacity and delay. We have investigated how the capacity and average delay can be improved in an Ad Hoc network with STDMA by using antenna arrays.

This thesis takes as its starting-point the different stands on the ever ongoing growth of multinational corporations (MNCs) and its consequences. Two opposing branches of theories, arguing that the establishment of MNCs in developing countries is good respectively bad for these countries, are tested for the aspect of state capacity. A quantitative method is then used to test if there exists such a relationship at all and if so, which of the two notions that are right.The presence of MNCs is measured as FDI of GDP while state capacity is defined as a combined index for three of ICRG's Political risk indicators. The two variables are analysed, mainly by cross tabulation, using an extensive dataset of 130 developing countries measured for a period of 20 years.The outcome is though ambiguous: No solid correlation can be found, but countries with a higher rate of FDI of GDP tend to have a slight worse rate of state capacity throughout the analysis. Thus the result points in favour of the notion that MNCs are bad for developing countries? state capacity.

With increased need for flexibility in timber deliveries, forest roads become an important factor. The disintegration of roads during the spring season can be avoided if it is possible to rule cutting areas to stands with good carrying capacity along roads with good carrying capacity. The goal with this work was to create a method to find the stands with high carrying capacity located near roads with high carrying capacity, and select them into a collection file. The method was based on Esri ArcGIS 9 and the tables that follow within that program. The method resulted in four different themes: 1. Collections with GYL 100 that cross the bufferzon for 0, 1, 2 and 3 class roads. Result 36 collections. 2. Collections with GYL 100 and 200 that cross the bufferzon for 0, 1, 2 and 3 class roads.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Husums plant has a selection of different pulp pumps at bleaching plant 4 and 5. The displacement- (HC-pump, Sund Defibrator PTD-60) and centrifugalpumps (MC-pump, MCA 42-200, MCP 30/20) are of interest in this report. The centrifugal pumps are controlled by throttle valves, which result in an energy loss. Chemical mixers are used to mix ClO2 into the pulp before proceeding into a holding tower where the bleaching process occurs.The energy demand of the different positions has been measured or calculated to be used in comparisons against new equipment. Quotations were requested and delivered from Valmet and Sulzer.

Crossfit is a recently developed form of training which is based on a number of functional resistance exercises performed at high intensity, often to the point of muscular failure. Crossfit has since its introduction 30 years ago, reached vast popularity all around the world, including Sweden. Its practitioners considers Crossfit to be an effective training method for achieving a functional and total trained physique thru improvements in VO2max, muscle strength, endurance, balance and speed. Few scientific studies has been published in the subject which is why this study sets out to examine the effect of Crossfit on VO2max (measured with Åstrands submaximal cyclingtest), maximal strength capacity in lower- and upper body muscles (measured with 1 RM tests in bench press and leg press), rapid strength capacity and strength endurance capacity in upper body muscles (measured with push-up test in 30 seconds) and explosive strength capacity in lower body muscles (measured with sergeant jump test). Five women with an average of 33(±5) years of age all new to Crossfit, performed these tests at two separate occasions with a training period of four weeks consisting of 12(±3,67) Crossfit sessions in between.The result showed a significant improvement in the maximal strength capacity of the leg extension muscles (p=0,025).

The purpose of this examination was to se how exercise affects the learning capacity. In this work I have chosen to integrate natural science with sport and the target group was a primary department. The two areas I integrate with sports were: the digestive system and knowledge of deciduous trees. I split the class in two different groups. One group got to have a theoretical lesson and the other one got to have an exercise lesson.

The interest for power and energy measurement has greatly raised with todays increasing electricity prices and enviromental awareness. In the search for energy efficient solutions, the measurements are more complex due to increasing of non linear components. Harmonics and non sinusoidal voltages put high demands on sampling and filtering. Meanwhile, the price must be controlled so the customer still will find it interesting to invest in smaller plants. ITT W&WW asks for a robust, heat resistant power meter with compact dimensions to allow mounting inside the casing of a pump.