The residential and service sector in Sweden accounts for approximately 38% of the total energy usage and Sweden has an aim to reduce the total energy use by 20% by 2020 compared to 2008, which means residential sector will have to improve energy efficiency. As part of that a law was instituted by the Swedish parliament that all properties must have an Energy Performance Certificate (EPC) to thereby give the property owners a greater insight into energy use in their buildings and propose recommendations for energy-efficiency measures. On the EPC, a value on the building's energy performance in terms of energy use in kWh / m2 per year is declared, of which electricity is a share of it. Instructions on what to include in the amount facility electricity for running the facilities is regulated by the authority for building, Boverket while SVEBY has made an interpretation of the regulations in their report "Brukarindata bostäder" where they have a table on what should be included in the amount and what not to include.This report is a study of two similar apartment buildings, where one of the buildings recently underwent renovation, to see if the declared amount of energy for electricity, in the EPC, is consistent with the measured value, and whether there has been any reduction in facility electricity in the renovated building after the renovation.The result shows that the measured value of the building electricity was 2.6 kWh / m2 per year, 28,8 %, lower than the declared value in the building that have not undergone a renovation. Calculation of values from previous years (2011) by the same percentage of facility electricity as in the results of the measurements, 56.7%, it becomes clear that the declared value for facility electricity in the EPC of the renovated building do not correspond with reality and that there has been an increase in use of facility electricity after the renovation..

The primary purpose of this study has been to investigate the Swedish timber industry?s perception of compression wood. A secondary aim has been to describe particular areas within the production process where compression wood is likely to cause problems. This study has mainly been carried out as a questionnaire. In order to connect the findings to current research, additional information has also been collected by means of a literature review. The questionnaire has been intended for sawmills and wood-manufacturing companies from various production classes and owner categories, as well as from different parts of the country.

The aim of this paper is to investigate what part film music plays in the creation of stereo-types in the production of Swedish cinema, in the 1990s and early 2000s. This period of Swedish cinema was largely defined through the visualization of life in the smaller provinces of the country. The results were reached through the analyzing of four important works of this era, representing different provinces and genres. The examined movies have shown frequent use of extreme characters and a somewhat hostile environment in search of an interesting story. The music is used in ways of describing class differences amongst the inhabitants and to set the gen-eral mood of the concerned provinces: an agent often working in the unconscious of the viewer in order to affect the final results..

Abstract. Title: Supply Chain Optimization ? for Sourced Production. Authors: Patricia Möller and Andreas Paulsson. Tutors: Jan Eskil Hollen ? Business Developer, Lilleborg as, Orkla, Everth Larsson ? Department of Industrial Management and Logistics, Division of Engineering Logistics, Lund University, Carl-Henric Nilsson ? Department of Economics and Business Administration, School of economics and management, Lund University.

It is becoming increasingly important for companies to meet customer demands due to intense competition in today's global market, that forcing companies to improve their offerings and become better at managing their supply chain (Shen et al., 2006).  Long lead times can be reduced by using different methods and strategies shows various researches. Lead times occur in the planning, production, inventories and handling of products (Treville et al., 2003).The aim of the study is to develop a method to analyze the factors that affect the length of internal delivery lead time in manufacturing companies. The method also included suggestions for reducing delivery lead-time to internal customers.The main factors that influenced the length of the on delivery lead times has summarized to make a selection among the factors that can have the most significant impact. The selected elements will be used as a method to analyze how these areas affect a company?s length on internal delivery lead times.The study shows that the causes of the long delivery lead times was the location of the customer order point, uncertain forecasts, long material and production planning time, and long waits in the production and storage.The delivery lead time, according to this report?s suggested improvements reduced by centralizing CODP and makes more reliable forecasts.

This report describes the process of outlining a design proposal for a resource planning tool for TV post-production. A feasibility study in form of a participant observation has been carried out on-site, which has resulted in a requirement specification. Based on the requirement specification, mockups have been created to illustrate the functions and features that a final planning tool should have. In addition to developing a design proposal, an evaluation of the existing resource planning tool Ganttic has been conducted. Ganttic has been reviewed based on how well it meets the list of requirements.

Companies that invest in e-learning have different expectations regarding the outcome of the investment. According to literature and articles it is common that companies see reduction of costs as the primary benefit with e-learning. Therefore we ask ourselves the question if companies have attained the expected benefit of the investment in e-learning and to what extent cost reduction have been a determining factor in the investments? The purpose of the thesis is to examine if companies that invest in e-learning have attained the expected benefits. We also want to examine what the reason for investing in e-learning is and if cost reduction is the primary reason for investing.

This essay revolves around the organization Mobile Art Production, MAP, and their artexhibition Street View shown on Kungsportsavenyn, Gothenburg two weeks in April 2010. Beingan alternative to traditional art institutions, MAP sets out goals for their activities and the aim ofthe essay is to examine whether the main goals of the organization were fulfilled through theexhibition. In Street View six Swedish artists participated with a total of seven artworks.The theoretical framework is formed using Arthur C. Dantos today classic essay ?The Art World?,Anne Ring Petersens definition of installation art and Nicolas Bourriauds term and bookRelational Aesthetics.

Environmental management officers ? leadership and employeeship in local environmental health authorityThe purpose of this study was to illustrate the working situation of municipal environmental health management officers. This is a qualitative study where I have interviewed ten environmental officers in ten municipalities in Sweden. The interviews were based on a half structured interview guide with questions. I have interpreted the interviews through different leadership theories.

Swedish healthcare are in need of radical changes to meet the requirements from both the government and the patients to create organisational working methods that better support the patients through their healthcare processes. Digitalization of patient data has been going on for decades in order to increase participation and understanding among patients in their care processes. However, availability of information does not ensure understanding. Therefore, resources should be devoted to create conditions to enable participation. The purpose of this study is to explore how visualization of patient data in the patient?s journal can affect the consultation in the encounter between the doctor and the patient.

Ala sawmill in Ljusne, Hälsingland, has increased its flow through the sawing plant during the last couple of years. The problem now is the sorting plant, as this part of the mill is now slower than the rest. A close analysis of the sorting plant was therefore necessary to be able to increase the flow through. The aim of the project was to find solutions that can lessen downtime and increase flow. The goal was to increase the flow from 650 to 925 logs through the sorting plant per hour.

The study examined what NHL-teams should improve. This has been done by studying the significant statistics of NHL-seasons, and with linear regression identifying what NHL-teams should do to win many points and thereby get a good placement in the final table. The most interesting result of the study is that the statistics on faceoffs and shots on goal and power play efficiency most seasons where irrelevant for the outcome of a season..

The study examined what NHL-teams should improve. This has been done by studying the significant statistics of NHL-seasons, and with linear regression identifying what NHL-teams should do to win many points and thereby get a good placement in the final table. The most interesting result of the study is that the statistics on faceoffs and shots on goal and power play efficiency most seasons where irrelevant for the outcome of a season..

The aim of this literature review is to give an overview of the differences between pure- and crossbreeding systems. Crossbreeding is a mating system with individuals of different lines or breeds. It is one of several breeding strategies in dairy production used to increase the economic profit. The use of crossbreeding increases due to changes in the dairy market and an increase of inbreeding among purebred Holstein. The main benefit of crossbreeding is heterosis, which is the improvement in genetic level in a hybrid offspring above the average of the parent breeds.

Hallstaviks papermill is an industry plant within Holmen Paper. Hallstavik is a mechanical mill and produce newspaper and journal paper. During year 2000, Hallstavik used approximate 1.200 m3f spruce, either as logs or chips from sawmills. Due to that the production is running continuously the mill also needs raw material at the same rate. At some periods the supply of raw material cannot keep up pace.