This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Trycksår orsakar lidande för patienter och höga kostnader för sjukvården. För att förhindra uppkomst av trycksår är det viktigt att identifiera patienter med ökad risk för trycksår samt att aktivt arbeta med preventiva omvårdnadsåtgärder. Ett strukturerat arbetssätt kan göras utifrån kvalitetsregistret Senior Alerts rekommendationer. Senior Alert är inriktat på förebyggande vård av äldre över 65 år och i registret registreras bland annat risk för trycksår, planerade åtgärder samt sjuksköterskans utvärdering av de insatta åtgärderna. Syftet med studien var att kartlägga täckningsgrad, utförda riskbedömningar och planerade åtgärder avseende risk för trycksår i kvalitetsregistret Senior Alert.

The purpose of this essay was to investigate the opinions of young people, age 14-16, at a school in a middle-sized city in Sweden, concerning narcotics. The questions we asked ourselves were;-What are young peoples' ideas of narcotics?-What do young people imagine when they think of a drug addict?-What reasons do young people give to start using narcotics?-What gender-related opinions do young people have regarding drug abuse?-What do young people think about legalization of narcotics?For this purpose we interviewed six girls and six boys. We interviewed them one at a time, for about an hour each. We used a qualitative method for the interviews.The young people in our study described narcotics as "dangerous".

Background:When the patient is critically ill the family is in a vulnerable position. The nurse's role is to support and help the family to find meaning in the difficult situation and to provide realistic hope. Balancing between the patient's and the family's needs is difficult. Knowledge about how nurses experience difficulties in the interaction with family is required in order to grant good care too critically ill patients and their family-members.Aim:To describe nurses' perceived difficulties in the interaction with family-members of critically ill patients.Method:The study is a qualitative literature-based study based on qualitative research. Results: The analysis resulted in four main themes; difficult disunion, environmental constraints, interpersonal difficulties and communicative difficulties.

This study examines the theories about intervention and sovereignty in relation to the world of today, with the raising question about humanitarian intervention in a globalized society.The purpose of this paper is to examine if intervention can be justified in a sovereign state and how it can be justified. The expected outcome is that conclusion can be drawn from the specific case with United Nations intervention in Bosnia and Hercegovina, and what kind of motives they putted up to justify their intervention.Because we are still living in the era of the Westphalia system with the inherited thoughts of state sovereignty, but in conflict with the new ideas of globalization and human rights, it?s of big relevance to look at this topic closer.First of all the reader is presented to the theoretical aspects of state, sovereignty and different kinds of intervention, to become more aware of the complications surrounding the relationship between these conceptions.The method used in this study is a motive analysis with the focus on the motives told by United Nation, to be the reason for the intervention in Bosnia and Hercegovina. The empirical results are based on the reports from United Nations Security Council during the years 1991 ? 1995.The results are that the intervention in Bosnia and Hercegovina can be justified when looking at the theories in relation to the empirical result, with the FN ? charter and the fact of violation against humanitarian law and human rights.One conclusion can easily be drawn, that individual rights are playing a big role in today?s global society and are putting some pressure on the United Nation to look over the rules about humanitarian intervention..

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The background of this study is the fact that it nowadays is more common to grow wheat after wheat. Usually we plow every autumn to remove the straw, and we wanted to study the effect of alternative methods to do it. We have done this experiment to answer the question if no tillage is better than conventional plowing. The results of the field experiment indicate that there is a link between plant establishment and the choice of equipment, but also a higher weed pressure in experimental plots with only ground tillage. The equipments which left much straw on the top of the ground the problems with fungi were more severe.

Atelektaser uppsta?r inom tio minuter hos 90 % av alla patienter som so?vs och leder till fo?rsa?mrad syresa?ttning men kan a?ven leda till postoperativa lungkomplikationer. Syftet med studien var att beskriva hur anestesisjuksko?terskan med olika ventilationsstrategier kan fo?rebygga atelektasbildning under generell anestesi. Studien genomfo?rdes som en litteraturstudie da?r 19 vetenskapliga artiklar granskades och analyserades.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible. When investigating the different principle of purifying water, a research of different products and their manufactories was done. These different products were compared and the principle of filtration was the most applicable, as most of the products were designed for far larger applications. As the process water contains quite large amount of particles, it is necessary to perform the filtration in different steps. The process water purifier is therefore composed of a module of coarse filtration and one of micro filtration. In the module of coarse filtration the mainly amount of fibres and particles are eliminated. They are kept back in the container unit with the larger fragments and dumped with these when the container is emptied. In the module of micro filtration the filtration is performed in two steps. In the first step particles larger than 50?m are eliminated, in the second step the micro filter is setting the range of purifying, in this case 10?m.