Milosevic, S. 2014. Buller ? Hur planers en bullerfri stad?. Kulturgeografiska institutionen, Uppsatser, Uppsala universitet. This essay is about noise pollution caused by urbanization.

Light pollution in urban areas - How to prevent light pollution at construction Jakob Sjöling Light pollution is a relatively new but rapidly growing form of pollution. Society's increasing demand for light coupled with the pace at which lighting technology evolves is accelerating that growth. The purpose of this study was to analyse how the construction industry plan and design outdoor lighting when erecting new buildings, specifically with regards to the issue of light pollution. It also investigated how local authorities work with these issues during urban planning. In both cases special interest was placed in ways to improve the planning and use of outdoor lighting in order to minimize light pollution.

Light has always fascinated humans but ever since the invention of the first light bulb, the use of artificial lighting has accelerated dramatically. Darkness has never been as rare as today and the overuse of lighting has created a new phenomenon called light pollution. Most living beings are biologically dependent on the recurrent twenty-four-hour rhythm of light and darkness, called the circadian cycle. Human beings are evolutionary developed after this circadian rhythm and the effects of constant artificial light is yet unknown. Scientists fear the consequences of constant lighting and what it means physically, mentally and philosophically for the human species.

This report is a Master?s Thesis performed by Andreas Adolfsson and David Jacobsson atChalmers University of Technology. The purpose of this master?s thesis is to evaluate anew method for load-shedding, the voltage controlled underfrequency load-sheddingdeveloped by ABB. This report presents a comparison between conventionalunderfrequency load-shedding and this new method for load-shedding.

The aim of this study is to evaluate whether the value of occupant load is over or under estimated when the Swedish general value for department stores, 0,5 person/m2, is used for dimensioning shopping centers. The data that was analyzed derives from seven shopping centers and one department store. A conservative method was used to calculate the occupant load factor. The analysis shows that two groups can be discerned: one group that is characterized by a lower occupant load factor that does not exceed 0,3 person/m2, and one group with a higher occupant load factor. Shopping centers with a higher occupant load factor are located centrally in large urban areas.

Inventories of epiphytic lichens on Scots pine (Pinus sylvestris) were conducted at three sites in east central Sweden: along the newly build motorway (Road E4), along the old road (Road 600) and in a reference site, to compare the effects of traffic pollution on lichen diversities. At each site, species richness, lichen mean sensitivity value (MK), air quality index of the forest stand/sample plot (LKI) and nitrogen impact value (N) were calculated and it was tested if there was any difference between the sites. Twenty-four species were observed in total, and Parmeliopsis ambigua and Hypogymnia physodes were the most common species at all sites. At Road E4, fewer lichen species were observed than at the other sites and this might be due to the impact of air pollution. The species richness at Road 600 was similar to that of the reference site, which might be explained by the improved air quality.

The reason for performing an Environmental Impact Assessment (EIA) is to incorporate environmental concern in different kinds of plans and projects. The purpose of such an assessment is to identify and describe direct, indirect and cumulative environmental impacts.Geographical Information System (GIS) is a tool that can be used to combine spatial extension of both sensitive areas and different environmental impacts in a quick and easy way. Because of that, descriptions of environmental impacts and motivation of different standpoints on a specific issue can be more correct and easier to make if GIS is used as a tool.Hence, GIS can contribute to improve the quality of Environmental Impact Assessments. If the benefits of using GIS are to out weight the costs, geographical information of satisfactory detail, actuality and accuracy need to be available at reasonable prices.In this paper, case studies are carried out for three different geographical analyses to investigate the use of GIS as a tool in EIA. From these case studies, more general conclusions about the benefits and limitations of using GIS for Environmental Impact Assessments are also drawn.

The main purpose with the project has been to approximate the magnitude of the pollution transport from the actual road surfaces and to get an approximation of the possibility to collect the pollutants to reduce the load to the water and improve the water quality.The quantity of pollution transport from the most trafficated roads areas in Örebro city has been calculated. Roads whith a traffic exceeding 10 000 vehicle/day. The study has been done with the calculation tool StormTac. Through analysis of traffic loads and road surface, which together with a different kinds of parameters gives an approximation of the pollutant transport.The calculation has included some metals and other substances in the stormwater and has also included the present of suspended solids. Included the overall study, some smaller areas has also been calculated for the possibility to remove pollutants.The work also includes calculation for three different areas for stormwater treatment.

Syftet med denna undersökning har varit att underlätta för företaget Re-Load att presentera sin lastpall som produkt för potentiella kunder. Syftet har också varit att stötta Re-Load till att bli licenserad EUR-pall samt att successivt ersätta befintliga lastpallar och långsiktigt exekvera företagets affärsplan. Målet har varit att undersöka produkten avseende lönsamhet, miljöinverkan och hur den påverkade arbetsmiljön. Under-sökningen har genomförts med ett befintligt flöde där produkten använts och utifrån detta kunde en flödesstudie samt en komparativ produktstudie utföras med en alternativ lastpall. Med data hämtat ur detta flöde utfördes en investeringskalkylering, miljöberäkningar, subjektiva intervjuer samt dokumentation.

In times of increased flooding, enhanced by climate change, polluted stormwater poses an increased threat to the environment through contaminated water entering waterways. Bioretention utilizes natural processes in soil and vegetation to treat pollutants and combat this threat. Biochar produced through pyrolysis, has a high cation exchange capacity (CEC) and could therefore increase treatment in bioretention systems. This research applies a literature review, interview, and a model to explore the benefits and disadvantages of biochar in order to specify a soil-mix through an understanding of the production process and preferred application rate. High purification through CEC, increased water holding capacity, and carbon sequestration being the benefits discussed.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

The industrialization in Sweden has increased the large number of areas that have been contaminated with various types of pollution. One of those sites are the property Höjen 3:24 in Arboga where ?Arboga Mekaniska Verkstad? once been. The property wants to increase the use of the old former foundry building with the adjacent ?plate-workshop? and believe there are two options for the building: That the building either should be used as a warehouse/concert hall, or rebuilt into a cultural center. An environmental evaluation has shown that the levels of heavy metals are over the Swedish environmental protection agency guidelines of less sensitive land.

The aim with my master thesis is to develop and test the applicability of methods to quantify and map solute advective travel times and pollutant transport at the catchment scale. Such quantification and mapping can increase the understanding of catchment-scale pollutant transport in general and contribute to the identification of the main sources of water pollution and the most efficient measures to reduce such pollution. The study area is the catchment of Oxundaån, about 20 km north of Stockholm. For detailed GIS modeling of water flow and catchment-scale contaminant transport in water, I´ve used new high-resolution elevation maps, land cover maps and soil maps combined with other available relevant data..

This master thesis sets out to compare the different public transport modes in Stockholm city.Both energy consumption and air pollution are compared. The chosen transport methods are car,bus and metro.Traditionally the rail industry has had environmental arguments as a strong competitiveadvantage when it comes to passenger transportation. However, in recent years the automotiveindustry has been getting more positive media attention regarding environmental issues, forexample Roger Kemp?s statement that the car is the most environmental friendly passengertransportation mode in the UK. This study will show the environmental advantages of railwaytraffic in cities.The energy sources of the world are not endless and the use of the different sources affects theenvironment in different ways.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.