Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey wasperformed. The voltages and currents have continuously been sampled in the incoming 10 kVsubstation HSP01 from April-August 2008. Power quality measurements were also performedin Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of theinduction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps tothe plant. The reason for the latter measurement was due to registered negative transients eachtime the motor was connected to the grid. The cause of the transients could be explained by thecoupling in the substation, the ageing of the motor which could result in damage of thebearings or resonance in the motor circuit which amplifies high frequency harmonics.

This report is based on a thesis that was carried out during spring 2012. The report covers the development of a preliminary study to Performance Sk8. The purpose of the study is to facilitate and contribute inspiration to Performance Sk8 to run an automation project to bring home their production to Sweden from China. The reason is to gain a greater ability to control quality, produce smaller batches and reduce the cycle time to reduce costs.The goal is that the preliminary study shall meet the requirements and wishes Performance Sk8 and other partners defined. The pre study will contain different cost proposals for the automation of selected process and serve as a basis for procurement of the equipment.The pre study has resulted in some proposed solutions to the various steps required to automate Performance Sk8 ?s production.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.

The work has been carried out in cooperation with the company Zenit Design in Malmö. The project's goal was to restore, improve and produce an ozone generator. During the project, the authors sought relevant literature in databases, been in contact with US suppliers of fuel cell membranes, Asian suppliers for the processing of Teflon and Titanium parts in mechanical engineering and Swedish suppliers of various standard components. The authors had access to a temporary lab at Zenit and electron microscope at Halmstad University where material tests were performed. The authors have also had access to measurement equipment to measure amounts of ozone.During the work, the authors have mapped how an existing ozone generator works and then have their own development.

Detta examensarbete syftar till att utreda vilka skillnader som råder mellan livslängdsprovning för transmissioner i rigg respektive fält för hjullastare på Volvo Construction Equipment (Volvo CE). Hjullastare benämns maskin i den följande texten. Uppgiften har delats upp i tre delar; ? Kartläggning av riggens uppbyggnad samt vilka tester som utförs i rigg respektive maskin i dagsläget. ? Analysera vilka effekter dagens skillnader i testning har på de transmissioner som provas i rigg respektive maskin.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

The report begins with a general inventory of possible technical faults in a hydropower plant and of possible fault indicating measurements. Then an investigation is made concerning a few different faults. Based on this investigation a choice on seal box condition and water leakage is made as problem for a more thorough examination, in which it is concluded that the turbine water leakage is larger when the turbine is put into operation. The examination ultimately results in a computer alarm for faults related to the seal box. Finally a few things are mentioned about flow measurement and pressure measurement in relation to the project as a whole..

Thesis completed by Johan Arvidsson, Alex Rasooli and Pontus Winroth, students at master program Product development and Design at the School of Engineering in Jönköping Sweden. The project comprises 30 ECTS credits and was carried out during the semester in the autumn of 2007.It was carried out in cooperation with Eksjöverken AB, subcontractor within the truck industry with special knowledge within the area of complicated machinery construction work. Job initiators at Eksjöverken were Mats Svanberg and Kjell Nygard. Dag Holmgren was acting as a tutor from the university. The task was to develop tools for trucks, primary toolboxes but in case of time also under run protection.

A substation must be properly protected against lightning and other external effects to the equipment in the station or staff, for that we use relay protection. They should also protect against internal errors which may occur as ground faults. There are different types of protection relays, but most common are overcurrent-, distance-, residual current- and differential protection.The purpose of this thesis was to deepen our knowledge of relay protection and to use the theoretical knowledge we got from the university studies in the work process. In the process we discovered which parameters were the most essential and calculated these for all relay protections on the substation. We also carry out a comparison between two brands of relay protection, ABB and Alstom.During our work we will test and simulate the over-current relays in a program called NEPLAN, the program will also calculate the fault currents.

Sitka spruce (Picea sitchensis) is a tree species that have its natural distribution along the West Coast of North America, from Alaska in the north to northern California in the south. Sitka spruce is a typical coastal tree species that can reach heights up to 85 meters and occurs in single pure as well as in mixed stands. The main purposes of this study were to describe the Sitka spruce growing characteristics and the volume production in comparison to spruce (Picea abies). The possibility to predict future volume production by using prognosis tools designed to be used on spruce were also studied. The material that has been used in this study are permanent sitka trials established by the Faculty of Forestry fixed Sitka trials and also material gathered in this study. A literature study was also carried out in order to determine the Sitka spruce growing characteristics. Sitka spruce has a high adaptation and a high volume production on a broad scale of soil types. The tree species is a pioneer species that has a fast early growth and in combination with sharp needles it is less susceptible to animal browsing than spruce. The factor that is the single most limiting factor for where the Sitka spruce can be planted is frost. This factor can be limited by using plant material with a well-suited provenance. According to the literature, the Sitka spruce has an average total volume production that is between 20-40% higher than spruce.