This report is a description of a developed educational simulator over rail vehicles and its components. The simulator is a hardware-based prototype over a door system on rail vehi- cles. System specialists and technicians will use the prototype. The Simulator should give the user a technical demonstration on how components work in a door system. The proto- type consists of motor, switch, relay and sensor.

Uppsatsens syfte är att undersöka hur företag använder sig av den interna information som affärssystemet genererar. Vi i studien vill också studera skillnader mellan en teoretisk idealbild och praktisk användning. En kvalitativ fallstudie av Perstorp AB genomförts för att undersöka ovanstående. Den primära insamlingsmetoden var en besöksintervju. I studien presenteras ett urval av de befintliga teoretiska referenserna kring information, affärssystem och styrning, samt hur dessa hänger ihop inom ramen för studien.

When the Eolshällproject was completed for the first time, a great deal of moisturedamage was discovered. Therefore the structure completion was removed andreinstalled. The project was originally planned to cost a total of 126 million SEK, but thefinal costs landed on 271 million SEK. What caused this failure? Were the designs poor,was the technology used too advanced, or was the project not managed properly?Based on the Eolshällproject, theses will be presented about what may have caused themoisture damage.

The purpose of this essay is to see if villages or bigger settlement locations can be found in south-eastern Blekinge during the viking age. There have been many archaeological findings from this period in Blekinge, for example grave findings, ring-forts , old roads and ancient harbors. But no evidence of a village has been found yet. If south-eastern Blekinge is compared with the area surrounding Järrestad on Österlen in south-eastern Skåne and the area surrounding Sorte Muld on Bornholm, many likenesses can be seen. In this essay, the findings in Blekinge will be used as different components when the three areas are compared with each other.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

This report is a description of a developed educational simulator over rail vehicles and its components. The simulator is a hardware-based prototype over a door system on rail vehi- cles. System specialists and technicians will use the prototype. The Simulator should give the user a technical demonstration on how components work in a door system. The proto- type consists of motor, switch, relay and sensor.

The topic of the present paper is to investigate and identify how two translators, Reginald Horace Blyth and David Landis Barnhill, differ in their translation of Japanese haikus by Matsuo Bashô to English. Three focal points of the study are; the translation of haiku rythm, the translation of kireji (a word for separating the haiku) and the translation of kigo (seasonal word). These three components are fundamental parts of Japanese haiku poetry and haiku experience, however there are no set rules on how to translate these haiku components to English. This study contains a comparative detailed analysis of five of Bashô´s haikus, in translation by Blyth and Barnhill. Sample haikus were selected from Blyth´s books A History of Haiku Vol.

SEP Modular Armoured Tactical System is the next generation of military vehicles developedby BAE Systems Hägglunds AB. At present time, BAE Systems Hägglunds AB aredeveloping a 6-wheel electrical hybrid and a conventional 8-wheel vehicle. The questionformulation was summarized as: ?In which ways can the electrical transmission in a hybriddriveline for SEP be designed, when the surrounding fixed interfaces are kept and the unity ofcomponents within SEP is maximized??. The purpose of this master thesis was to study avariety of concepts for hybrid propulsion.

SAAB Aerotech division FGR in Arboga builds and develops equipment and components used in both military and civilian applications. To build a test system for a specific project that SAAB is responsible for requires a simple signal generator that can provide a pulse modulated signal. The need to buy a new advanced signal generator for example from Agilent is not as profitable as the instrument is expensive and contains features that SAAB does not require in their applications and test systems. That was the reason why SAAB offers two students a thesis where the goal is to construct a signal generator in accordance with what SAAB requests.This thesis contains several different phases. The first step was a meeting with our supervisor Mats Bergman and by reading the data sheets for components to be used in the project, with these information and specifications that we have received from SAAB we started to construct the signal generator.What we did during the construction work was to simulate and draw a schematic to be able to design the circuit board.

We have chosen to focus this paper on the importance of game-components in the MMORPG-game World of Warcraft, in order to discover which of them who are the most important and create the biggest motivation to play the game for the players of World of Warcraft. We made this  investigation because we wanted to find out more about the specific reasons about what people think is especially great with World of Warcraft and makes them want to play it for hour after hour. By doing this we wanted to find out what it is that is so appreciated with this game. But this is a big area and it has therefore been difficult to find a way to satisfy and make those who have answered on our survey to feel that the game-component they enjoy most has been a part of our questions.To solve this problem we did a survey that included 200 persons and two interviews. When both the survey and the interviews had been completed, the result was being compared against each other and together to see if there was any difference between them or if they had any similarity to the attraction and motivation.

This thesis includes a description of the project flow for our projects at Semcon. The emphasis is on designing a manual for elMaster Concept.The project flow provides several minor and major elements plotting schedules for this project and the establishment of a manual. When a schedule is drawn, lists and tables with components and connections can be created. This is done to better manage drawings and make changes. These diagrams and tables are used in product manufacturing, testings, controls.

In this report you can get a complete instruction about how to build your own development system for the PIC-processor. This card will be used for laborations for the students at LITH-ITN. With this card you can send new assembler codes (new instructions) down to the microprocessor via the Serialport on your computer. Then the new instructions for the microprocessor will start to execute. We made a solder paste stencil at Campus Norrköping solder paste stencil laboratory.

Dione kullager AB is a company in Uppsala, which sell industrialmachinecomponents, transmissionsolutions and provides repair serviceof hydraulic components.When a hydraulic cylinder is about tobe repaired it needs to bedisassembled. Because hydrauliccylinders usually work in dirtyenvironments and are heavilyworn some types of cylinders arealmost impossible to disassemble.Today the disassemble is made by hand,which means extra work for themechanics. In order to facilitate thedismantling of this type of cylindersa machine is to be developed for thispurpose and this is where this thesisbegins.The thesis has been organized in threephases: Literature study in whichfacts and theories are acquired.Concept generation in which differentconcepts, calculations, and solutionswere identified and selected. Thedesign phase where all the differentconcepts of components were assembledand simulated in SolidWorks. Similarstructures have also been studied inorder to identify necessary functions.The thesis resulted in a structurewhich is believed to meet therequirements.

This thesis has been written at Linköping University for the company Instrument Control Sweden AB (ICS).ICS is a small company located in Linköping that develops software and hardware for Unmanned Aerial Vehicles, UAV. At present, ICS has a fully functional autopilot called EasyPilot but they want to reduce the autopilot?s size to make it more attractive.The purpose of this thesis was to investigate if it was possible to reduce the size of the autopilot and how, in that case, it would be done. It was also necessary to examine whether the old processors should be replaced by new ones and how hard it would be to convert the old software to these new processors.To succeed with the goals many of the old components had to be changed for new, smaller ones. Some less necessary parts were also completely removed.

To create a profitable and competitive business an important factor today is a well-functioning logistics. Through effective internal material flows effective logistics can be achieved. Unnecessary handling and movement of materials is a waste which affects the internal material flow. These wastes should be identified and eliminated as much as possible to improve the internal materials handling and through that achieve a more efficient business. At Fagerhults Belysning AB, where professional lighting systems are developed, manufactured and marketed, a new inventory has been built and changes in the assembly has been made during the past year.