Scandinavian Biogas is involved in the planning of a combined ethanol and biogas factory in Karlskoga, Sweden. Besides biogas and ethanol large amounts of digester residues will be produced, about 450 000 liquid tonnes residue (~7,3 % Dry Substance( DS)). The objective of this thesis was to investigate possible uses of the residue from the biogas production process ScandgasEthanol developed by Scandinavian Biogas, and to derive a methodological approach how to evaluate and compare handling systems. Three systems where proposed and compared in this thesis; spreading of the untreated residue as fertilizer (system 1), dewatering to a higher DS content to reduce transportation before spreading as fertilizer (system 2) and production of a solid fuel by dewatering and drying the residue (system 3). The general conditions for the proposed systems were investigated in terms of practical viability, economical aspects, environmental impact and energy inputs/outputs.

The Swedish production of biogas was 1,5 TWh 2011. About half of the production was used as vehicle fuels. The cost for upgrading biogas depends on the size of the biogas plant and its gas production. If the gas flow is low the cost will be high. However, further development of existing upgrading technologies or development of new ones, have good potential to decrease the upgrading cost for small scale biogas plants.

 With the increases in fuel costs due to the depletion of the world oil reserves and the increase of greenhouse gasses as a consequence to using oil as a fuel many companies are looking to new and innovative ways to power their aircraft. One of these new ways to power an aircraft is using fuel cells powered using hydrogen and oxygen, thus producing nothing but water vapour and small amounts of nitrogen dioxide as well as trace amounts of other emissions. Both Boeing (1) and Politecnico di Torino (2) have shown that it is possible to build an all-electric aircraft powered by fuel cells. Both flights used small, two-seater aircraft and a constant between them was the loss of the co-pilot seat due to weight and lack of space. As this paper will deal with a commercial aircraft a primary concern is the cargo and passenger capacity and whatever impact switching propulsion system has on these.

Dimensional stability is an important aspect of fuel mechanical design and licensing of new fuel designs for nuclear power plants. Dimensional changes within the reactor can affect the safety margins against overheating of the cladding and the pellets, therefore it is crucial that the dimensional changes are kept to a minimum.The profits per produced kiloWatt hour continue to decrease for the Swedish nuclear power plants. Some reactors are even operated with a calculated loss. To reduce fuel costs and thereby improve the profit some reactors are operated with higher uranium enrichment, so that the assemblies can reach a higher average burnup. This increases the neutron fluence to the pellets, cladding an spacers.

The use of bio fuel is increasing every year. Nowadays you will find different alternatives to oil and electricity heating system. In this essay I have examined what the economic conditions are to invest in a bio fuel furnace. I have chosen to assume from a specific farm and do a case study on this farm. Malmvik farm is located just outside of Stockholm.

The demand for biogas as vehicle fuel has risen sharply and there is a great need for increased production. A possible addition of vehicle gas can be produced by upgrading landfill gas which is formed by degradation of organic waste. This thesis investigates the potential of producing vehicle fuel from landfill gas in the region of Biogas Öst.In 2008, an amount of 32 million Nm3 landfill gas was extracted in the region. This level can be maintained for another ten years if the efficiency of gas extraction is improved. The annual production will decrease with time since landfills aren?t allowed to receive more organic waste.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The milling process creates a wide range of particle sizes.

New energy resources that can replace petroleum diesel are needed and biodiesel may be an excellent substitute. During storage and use, biodiesel can oxidize and form peroxides, leading to degradation of the fuel. It is therefore important to determine the peroxide content of the fuel. In this thesis the triphenylphosphine method, which involves GC-MS analysis has been compared to the standard iodometric method which involves titration with sodium thiosulfate. Working standards were made to see how well the iodometric method worked and also in order to make a calibration curve in GC-MS.

The environmental requirements and laws on combustion engine emissions are very tough today andthey will become even more stringent in the future. To achieve these requirements there are highdemands on the control systems for these engines. An improved precision in the measurement of anengine's speed and position gives the electronic control system an even better timing when it comes tofuel injection and ignition. This makes the engine more fuel efficient, reducing the emissions. This thesisis part of a collaborative project between Hoerbiger Control Systems and subsidiaries.

This study has analyzed particel size distribution and needle content in chipped logging residuals (branches and tops) delivered to the district heating plant Ryaverket in city of Borås, Sweden. Two fuel assortments has been analyzed: Chipped logging residuals from pure softwood and from mixed fuel (connifers and broadleaves). The samples has been sieved at Linneaus University laboratory.The study of particle sizes indicates that only 53,2 % of delivered fuel is within the fuels specification (7? 45 mm). The needle content is in this study 12,4 % (dry mass) which is higher than expected..

Mathematical models possible to simulate are of great importance in order to make successful projects in the aircraft manufacturing industry. An aircraft fuel system is very complex, containing pipes, tanks, orifices, valves and pumps. The principal of this thesis is using the tool Easy5, which no longer is considered reliable enough in terms of development and support. This thesis tries to evaluate the Modelica language as a possible alternative to Easy5. To make this evaluation, the components concerned in the fuel library in Easy5 are implemented to the Modelica language.

There are several energy systems in the Swedish society and to ensure the comfort and health of the citizens it is of importance that the different energy systems are functioning properly. District heating is one of these energy systems and many household depend only on district heating to warm up their homes. District heating is dependent on several processes where every step needs to function in order to deliver the produced heat to the end consumer. Previous studies have investigated the distribution of district heating and how to make customers choose district heating as their heating method. The supply of fuel to the district heating plant has not been studied as much, even though it is an important part of the whole system. This thesis is a part of the project NORD-STAR (Nordic Strategic Adaption Research), which has focused on climate adaption in the Nordic countries.

Reducing the CO2-pollution, resulting from the combustion of fossil coal for energyproduction, is important to affect environmental changes. One way to achieve a reductionis to use the oxy-fuel technology. The technology uses O2 and re-circulated flue gasduring the combustion which results in a flue gas mainly consisting of CO2. The flue gascould then be compressed and stored without environmental effects. A problem thatfollows from the compression is the risk of acidification in sensitive parts of the process.Acidification can occur because of reactions following from the contact of condensedwater and sulphur- and nitrogen-oxides which are also present in the flue gas.This report compiles and evaluates the basis of a scientific unit with the purpose ofexploring the possibilities of extracting impurities of SOx and NOx from the flue gases.The dimensions of the unit are based on basic conditions, defined for an existing oxy-fuelprocess at Chalmers, and on the results of computer modelling.

There have been changes in Earth?s climate system on both global and regional scale since the pre-industrial era and some of these changes are due to human activities such as the combustion of fossil fuels. This calls for the development of engines with a higher efficiency and less harmful emissions. One interesting concept is the Homogeneous Charge Compression Ignition (HCCI) engine, which has the advantages of potentially low emissions combined with high efficiency. However, HCCI with diesel fuel requires a relatively long fuel/air mixing time to ensure a "homogenous" charge.

Every year, KTH participates in the Shell Eco Marathon, a competition whose goal is to design a vehicle that can go as far as possible using only the equivalent energy of one liter of petrol fuel. This year, one of KTH?s contributions to this race is the Agilis prototype; a car powered by a uniquely configured HCCI-engine developed at the university. The engine is dependent of several subsystems in order to work properly, among other, systems for cooling and lubrication.Combustion engines are in need of a cooling system that reduces the heat developed during the combustion. In general, two main types of cooling systems are employed; either air cooling, where the outside of the cylinder is exposed to a flow of the surrounding air, ore water cooling, where water flows in tubes around the engine, and the heat are transferred by the water to the surrounding air through a heat exchanger.The purpose of the lubrication system is to prevent the friction that builds up in the interference between moving parts in the engine.