This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Writers: Johan Lundqvist Eriksson and Elin SandbergSupervisor: Stig AnderssonEnglish title: Allocation of revenue in the hospitality industryKeywords: Revenue allocation, cost allocation, profit center, Du Pont model, taxes and manipulation of data.Date: January 2012Since the taxes for food and lodging has been different in Sweden for many years, the hospitality industry has come up with a way to save money on tax paying. When private customers stay for a weekend where the meals are included, the business is placing more than the relevant revenue on the lodging part, which has the lower tax. Because of this the results has improved and tax money has been saved. Now when the Swedish government has decided to lower the tax on food to the same level as the lodging, the chances for correct revenue allocation arises. When we approached the hospitality industry with our problem area a big interest was showed from the head chefs. They now see a chance to get more income on the meals and through this be able to show better results towards the owners.Two hotel managers at two different hotels and their head chefs were chosen for interviews.

Uppsatsens syfte är att försöka förstå, utifrån existerande teorier och med hjälp av insamlad empiri, vilka parametrar i ett kundperspektiv som är av betydelse vid utvecklingen av en prissättningsförmåga bland business-to-business-företag.Vi har använt oss av en kvalitativ metod vars ansats är av abduktiv karaktär. Den empiriska datan har samlats in genom semi-strukturerade intervjuer vilka har genomförts via personliga möten samt via telefon. Då vi betraktar prissättning som en förmåga, vilken återfinns inom företaget, så utgår det teoretiska ramverket främst från det resursbaserade synsättet vilket styrks av en akademisk artikel som beskriver och förklarar bakgrunden till att prissättning kan ses som en förmåga. Därutöver beskriver vi den vanligaste prissättningsstrategin företag emellan; cost/plus-strategin. Vi argumenterar för att företag bör införa rutiner och skapa en entydig struktur, med särskild fokus på tre områden, för att försäkra kunden om att de erbjuder produkter med kundvärde.

The work that is the basis of this Master Thesis was performed on Scania´s group of cabdevelopment, and concerns the GPS-system in Scania´s trucks. Today, the GPS-systemconsists of an active antenna mounted on the roof of the truck. The antenna is connectedto the receiver with a coaxial cable.The purpose with this Master Thesis was to develop and evaluate a new GPS-system,where the information is distributed using a LIN-network. Today, each unit requiringGPS-information is equipped with its own antenna and receiver. This solution has beenthe most cost effective to this point.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Welding is a common method for joining of metal or plastic construction parts. This report describes several different weld methods in general terms. The report focuses on the GMAW method, specifically MAG welding.A case study has also been performed for the company Wenmec. The task received from the company was to compare the mechanical properties of joints welded with the tube electrode called Nittetsu SM-3A and joints welded with the homogenous electrode called ESAB Aristorod 12.63. Both types of weld joint were welded with the MAG method with an Argon based shielding gas with 18% CO2.

The project aimed to develop a protective and stabilizing insole called Trailplate for soft andlight shoes. The demand came primarily from off-road runners in France, Switzerland, andAustria. The project was carried out at Icebug, a company that develops shoes mainly forrough terrain. The main focus has been on the trailplate which is designed to fit severaldifferent shoes.Torsional stiffness and bending resistance were the main objectives. To improve the existinginsole, a material with the right features was required.

The thesis work was conducted with the company Free2Move AB. The company is located in Halmstad and is an acting provider of wireless communications for industrial customers, mainly focused on Bluetooth? technology.In today's society most people have their music on their computer, MP3 player or mobile phone. What if you could avoid the cable between your sound system and sound source and transfer music wirelessly instead? Together with the company's engineers, I have developed a new comprehensive product for wireless music transmission.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

In an attempt to develop a more cost-efficient material for solar   energy applications, nano-particles of nickel oxide composite in a silikatmatris manufactured with solar gelmethod and studied structurally by electron microscopy. Furthermore, the thin film optical properties characterized by Variable. Angel Spectroscopic Ellipsometry. Sol gelfilms suitability as a selective absorber surface is also analyzed by optical modeling..

Avsikten med uppsatsen är att utvärdera och analysera implementeringen av en ny teknologi, vilken befinner sig i en nätverksdriven marknad. Studien ämnar se till de överväganden företag står inför vid implementering av Anototeknologi, förändringar som implementeringen medför samt de för- och nackdelar som uppleves. För att nå syftet med denna undersökning används kvalitativa intervjuer uppdelade i två fall med två slutkunder till företaget Anoto. Teorierna som används och ställs mot empirin är disruptiv, plattforms teori, nätverkseffekter, switching cost & TCO. Uppsatsens empiriska material består av kvalitativ data erhållen från intervjuer med två Anotopartner: Penboosts Solutions AB och Catrel AB, två slutkunder: Würth Svenska AB och Hemtjänsten i Sundbyberg, tre användare av Anotopennan: två Würthsäljare och en hemtjänstarbetare, samt sekundärdata erhållen från de undersökta företagens hemsidor och annat informationsmaterial.

Today?s electrical grid companies understand that better knowledge of and information about their grid can help realize a smart grid network. One way to gain better knowledge and information about the low voltage network is to install measuring equipment on the substation transformer´s secondary low voltage side that measures the low voltage network losses for that specific substation. By doing so, grid companies can, due to the calculation of the low voltage network losses, identify and address issues such as illegal power dissipation, unmeasured power outtakes, and unsatisfied technical documentation for the substations low voltage network.During 2012, Mälarenergi Elnät AB had a total electrical network loss (both medium and low voltage network losses included) of three to four percent of their total distributed electrical volume. Converting this energy volume into a monetary figure this accounts for a loss of around 30 million Swedish crowns.

The long-term external financing of a corporation is satisfied through the bond market where issues of index-linked bonds, which are discussed in this thesis, is one alternative. (Finnerty&Emery 2001) An index- linked bond is a debt instrument where the investor is guaranteed the principal and premium amount in real terms. As the bonds cash flows are indexed to the inflation this implies that the issuer of an index-linked bond assumes an inflation risk. Purpose: The purpose of this thesis is to describe and examine corporate motives for choosing index-linked bonds as way of financing their business. Realization: Primary data was collected through interviews with corporate issuers of non-swapped index-linked bonds.