Until 2020, 49% of Sweden's use of energy must derive from renewable sources. Greenhouse gases must as well decline with 40% compared to 1990 as a part of Sweden's 16 environmental objectives. Biogas is part of the effort to achieve these objectives, but as the demand for biogas increases, more substrates are needed to meet the demand. The purpose is to investigate the conditions for pea residue as substrate by performing lab-scale mesophilic digestion with different fractions and notch lengths and then to summarize pea residue as a substrate for biogas production. During anaerobic digestion, 1000 ml bottles were used as reactors for digestion.

Acid sulphate soils is a wide spread problem along the northern coast of Sweden. This is causing great damage through low pH and leaching of metals out into the streams. These soils are estimated to be found in several places in Sweden but also in many other areas in the world. One of these areas in Sweden that are believed to contain these sediments is Mälardalen. The purpose of this study is to evaluate the extension of the acid sulphate soils in this area.

During whole-tree harvesting, there is a risk that the soil will become impoverished of nutrients. To prevent this, nutrients are returned to the harvested site as wood ash. This action also reduces the risk of soil acidification. Nevertheless, the ash does not result in any increase of tree growth if it is added on mineral soils, which is where the measure is most commonly used in Sweden. Due to the lack of growth response, the interest from landowners is small, which is why ash amendment today is not done enough to compensate for the need.

I mitt examensarbete har jag undersökt om det lämpar sig att använda en manuell metod för att skapa normal maps till icke-organiska polygonmodeller avsedda för datorspel. Jag har använt mig av Photoshop för att måla normal maps som jag sedan applicerar på lågdetaljerade modeller jag skapat, för att höja detaljgraden avsevärt. Då icke-organisk modellering inbegriper modeller som ska representera hårda ytor, och därmed inte animeras med deformation, så antog jag att denna metod skulle lämpa sig väldigt väl åt dessa ytor som ofta har extremt mjuka former och precisa vassare kanter. Min metod har varit att studera litteratur om Normal Mapping och hur man använder Photoshop för detta. Jag har sedan utfört praktiskt arbete för att utvärdera hur effektiv metoden är samt vilka fördelar den bidrar med. Jag går igenom teori för normal mapping som jag stödjer med hjälp av faktatexter och instruktions-DVDer i ämnet för att sedan redovisa metoden jag använt i mitt arbete. Jag avslutar sedan med en diskussion kring mitt resultat och redovisar vad jag kommit fram till genom mina experiment. Jag kommer fram till att Normal Mapping med Photoshop är mycket väl lämpat åt hårda ytor och även bidrar med optimeringar i arbetsflödet både vad gäller organisering, tidsåtgång samt kontroll över resultatet.

As a small and land scarce country, effective waste management is ofoutmost importance in Singapore. In this study the production of biogasthrough anaerobic digestion from the organic fraction of municipal solidwaste (OFMSW) was compared to incineration of the waste. At the momentalmost all of the OFMSW in Singapore is incinerated. Three differentscenarios were compared to the reference scenario (incineration): one with alarge scale biogas plant that can treat half of all OFMSW in Singapore, onewith a medium scale biogas plant about 15 times smaller than the large oneand one with a small scale biogas plant that can treat waste from e.g. ashopping center or a food center.By using life cycle assessment (LCA) the different scenarios were comparedin terms of global warming potential (GWP), acidification, eutrophication,energy use and land use.

When rubber equipment in a milking system ages, physical and chemical deterioration occurs and cracks, crevices, as well as deposits of organic and inorganic material is formed on the surface. Bacterial colonization can accumulate, especially on ageing rubber equipment and if the cleaning procedure is not functioning properly. Formation of biofilm in milking equipment could in turn cause bacterial contamination of bulk tank milk. ATP bioluminescence is a fast and easy way to determine the hygienic status of a surface based on its ATP content, and results are given in relative light units (RLU). The method measures both bacterial contamination as well as residues from other organic material.

Storage of biomass is associated with problems like heat development, biomasslosses, and reduction of the fuel quality. Certain processes such as biological- andchemical degradation are responsible for these storage problems. This master?sthesis was carried out at Vattenfall Research and Development AB and is alignedtowards quantifying the biomass losses from short-term storage (1-2 months) ofbark and recovered wood. The biomass was stored in outdoor piles during differentseasons, campaign 1 (summer) and campaign 2 (autumn).

In 2013 a new emission standard for heavy trucks was introduced and hence a number of new parts was brought in to Scania CV AB. This created a need for modifications in the silencers flow. The flow is highly complex involving several suppliers, call off methods and different models of silencers. The aim for this project was to improve the existing silencers flow. The flow, from supplier to assembling, has therefore been mapped.

The purpose of this report is to investigate the possibilities with drain water heat recovery (DWHR) in residential buildings. Information and relevant theory has been collected and summarized in this report. Calculations have been done for given scenarios to evaluate profits. DWHR heat exchangers use simple technology and have long life-time. The heat exchanger is connected to outgoing drainage pipe and incoming cold-water supply so countercurrent flow is accomplished.

Forest streams and the associated riparian zones are sensitive to disturbances and changes that occur within these riparian areas. Particularly sensitive are small streams of low order, which will have large impacts down-stream. The disturbances that occur in the riparian zones are reflected quickly in the stream. Driving with forestry machines in the riparian zone will have detrimental effects to the soil and water. Driving the machines will lead to changes in the mineral soil composition, resulting in the reduction of porosity, less infiltration, compaction, and an increased bulk density.

Bath has been a part of human history for a long time. Today bathing/swimming inmunicipal pools is for people of all ages and it is possible to take swimming courses,exercise or enjoy recreation. The municipal indoor pool of Hogdalen in Sweden wasbuild in the sixties and has had problems with high levels of heterotrophic bacteria. Thefacility has two larger pools, one adventure park for young kids, two smaller bath tubsand a jacuzzi. To improve water quality UV light and coal filter were installed inOctober 2009 to the already existing purification system.

Tryckeribranschen är en ekonomiskt pressad bransch som söker nya besparingsmetoder. En av metoderna är att minska insatsvaran tryckfärg med färgreduceringsprogramvara.Rapporten undersöker möjligheterna med färgreduceringssystem. Detta genom att studera hur man använder sig av färgreducering och hur det påverkar trycket.Studien avser besvara:? Hur stor färgminskning kan man använda sig av utan negativa konsekvenser på bildkvalitén?? Hur går man tillväga för att skapa den färgminskningen?? Överensstämmer total färgförändring och visuell bedömning av tryck?För att få svar på dessa frågor togs en testform fram med nödvändiga bilder och färgfält som sedan genomgick en rad färgreduktioner. Testformen utvärderades digitalt med avseende på TAC och total färgförändring.

This thesis work was made for Södra Cell Mörrums bruk in Blekinge. The purpose of the work was to develop a computer model in the simulation program Extend for the removal and balance of organic oxygen consuming substances, measured as COD (Chemical Oxygen Demand), in the new biological treatment plant in the mill. The plant produces two different pulp products, TCF- (Totally Chlorine Free) pulp and ECF- (Elementary Chlorine Free) pulp, for sale. The different bleaching procedures affect the characteristic of the wastewater and thus the effectiveness of the biological treatment plant.In the model that was developed the COD in the wastewater was divided into five different COD-fractions: soluble easily degradable (SS), soluble hardly degradable (SR), soluble inert (SI), particulate inert (XI) and particulate biomass (XB). To create the model FlowMac? was used as a base.

Storm water is defined as runoff from precipitation such as rain or snow. It is collected in sewage disposal systems and since it mainly originates from urban areas it can contain high levels of heavy metals, nutrients and oil etc. Polluted storm water is currently treated by different methods such as wet ponds, constructed wetlands and filter strips. This study investigates these methods, which in earlier studies have shown to give varying results regarding their treatment efficiency.This thesis has been written on commission of SWECO VIAK and was aimed at studying those parameters that may affect the treatment efficiency of nutrients and heavy metals in storm water treatment facilities (STF:s). Through literature studies the dominating treatment processes in ponds and wetlands were examined.

In order to avoid harmful substances ending up at the municipal sewage treatment plants, it is important to purify the wastewater at the source. One such source is the wheel washers available in many tire garages which are used to wash the wheels on our vehicles when we change between summer and winter tires. It is important to wash the wheels before storage, to extend the tires lifetime. The purpose of this study is to find a green innovative solution for reduction of emissions of heavy metals at the source, so that the sludge from the sewage treatment plants can be used as fertilizer. The target is to find a wheel wash method which leads to compliance with the guidelines for car washers, and that also provides a better washing result than with the existing method.