In this final thesis two simulation models have been integrated. The simulation models are models of JAS 39 Gripen?s fuel system, software and hardware. The time consuming and costly work to develop software has made the department of fuel system to build two models in Xmath/Systembuild. The software model also simplifies the comprehension of how the software in the control computer of the fuel system works.

The purpose of this thesis has been to build a parameterized model of a prototype motor in the program Solidworks, to use in future optimization of aspects of effectiveness and weight. The result were two models. The first model were one minor part of the whole design in 2D, to be able to optimize and study the minor part with a faster loss simulation. The second model was the whole design in 3D. The whole model were done with the three programs Solidworks, Comsol and Matlab.

Mosquitoes are found in extremely large numbers in the lower parts of the River Dalälven. In the year 2000 the mosquito nuisance was especially high, resulting in foundation of the Biological mosquito control project. Since 2001 mosquito larvae are controlled by using a biological pesticide BTI (Bacillus thuringiensis ssp israelensis). The mosquito fauna in the area is dominated by flood water mosquitoes, a group of mosquitoes that are very aggressive and form new generations of mosquitoes during every single flooding event during the summer. To be able to efficiently control the mosquitoes it is essential to know the extension and locality of the flooding.

The main object of this diploma work thesis is about how computer programs can bea tool to use for work on stormwater investigations. The advantage of using acomputer program compared with calculations made by hand is evaluated anddiscussed. The computer programs that have been used for studies and a sequence oftesting of the possibilities are Autodesks Storm and Sanitary Analysis and DHIs MikeUrban.Focus on sustainable development now permeates the building industry. As a resultstormwater investigations have been conducted in an increasing extent the recentyears. Stormwater is water produced due to precipitation, such as rain and snowmelt.Stormwater investigations normally contain descriptions of existing land use, plannedland use and suggestions of measures and technical solutions for the future disposal ofstormwater.The initial part of the thesis consisted of literature studies on stormwater andstormwater investigations to understand the science.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.

Hydroware Elevation Technology AB sells control and regulation equipment for hydraulic elevators. The company now wants to investigate the possibility of changing their present softstarters to frequency inverters to supply power to their pump engines. They also want to investigate the possibility of future use in so called ?intelligent? houses.The purpose of this report is to investigate these possibilities..

Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest production cost. The production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

Modelica is a multi-domain and equation-based modeling language. Modelica is based on object-oriented principles and non-causal modeling. The language is constructed to facilitate reuse and decompose models. The models and the modellibrary can modified to design a new nonlinear components.Object-oriented modeling is an excellent way to analyze and study large complex heterogeneous physical systems. The object-oriented modeling approach build on reusing and decomposition of models and non-causal modeling.Modeling physical systems often leads to a DAE system with index 2 or 3.

This master thesis studies how much the cycle time, i.e. the time it takes for an industrial robot to perform a given task, can be reduced if an extra degree of freedom (DOF) is added to the robot system. The extra DOF consists of a linear track, which is supposed to be used in an optimal way. The problem has been studied using simulations in the robot simulation tool RobotStudio. To be able to run an optimization in Matlab, with the RobotStudio simulation cycle time as the object function, communication between Matlab and RobotStudio has been set up with an interface written in Visual Basic.

This bachelor thesis in mechanical engineering was performed during the spring2015 in collaboration with Composite Consulting Group in Laholm. TheComposites Consulting Group works mainly with design and details of differentcomposite projects, their main area is FE-calculations, 3D-modelling andmechanical tests with composite materials.The aim of this bachelor thesis was to simplify the calculation process of solidmechanics for sandwich panels by simulation with computer software. The goalwas to decrease the time for the design and calculation process of the constructionand the cost of the practical tests. Our task was to build a static three dimensionalmodel with the computer software Abaqus, where the result should correspondwith the practical pressure tests in laboratory.The project started with collection of material data from Composites ConsultingGroup and by learning the software Abaqus, simultaneously a specification wasdeveloped in corporation with the company. Later on, a static wheel pressuremodel in the software Abaqus was produced which simulated the behavior of thesandwich panel during static wheel-pressure by a pallet truck.

This thesis deals with different methods for measuring moisture-related dimensional changes ofwood. Typically relative humidity is measured to determine if the ambient climate around anobject is harmful to it or not. Values between 40 to 65% RH are recommended for hygroscopicmaterials. To know how a wooden object actually reacts to changes in the surroundingenvironment requires methods that involve the object itself. Because of the wood anisotropy,differences in wood structure, finishes and other restraints, it is not always possible to predict themovements.This paper addresses various measurement methods, primarily methods that have been testedin the field of conservation, with examples of their use.

AbstractIn urban societies people spend more and more time indoors, which put great demands on the indoor environment. If the ventilation is to manage the removal of unwanted substances in the indoor air, a good mixing of the air is required. The question arises that, whether the buoyancy forces will counteract a good mixing of the indoor air or not?This report aims to clear up the difficulties whether you need to consider the buoyancy forces or not, when adjusting a ventilation unit. For studying the indoor mixing of the air a two dimensional model is constructed in COMSOL Multiphysics.

By our employer Camatec Industriteknik AB have we been given the assignment to continue with the previous work ?Design of strip feeder?. Our goal with this work is to come up with a design basis for a strip feeder.Functionally a strip feeder consists of two rollers which with the aid of the friction between the strip and the coating on the roller create a strip force that pulls the strip through the working progress.Demands on this project:? 10 ? 600 mm in strip width and 0,1-1 mm in strip thickness.? Minimum 30m/min in production speed.? A maximum strip force on 30-40 kN.? The cost of the strip feeder?s components is to be considered of economy and quality.The need of a strip feeder occurs when the coil doesn?t manage to feed or pull the strip before or after a working process. The strip can otherwise be exposed by a permanent yield deformation or a change in the strip material if it?s pulled trough the working process only by the on ? and of-coils.

This thesis work includes studies and simulation how magnetization of the translator in a linear generator for wave power can be automated. The translator is the moving component in the generator that is "dressed" with permanent magnets. The translator is magnetized with rectangle-shaped permanent magnets that are today's strongest permanent magnet type of neodymium-iron-boron (NdFeB).Eight equivalent metal sheets are mounted around the translator. The plates have milled tracks where 106 permanent magnets per sheet are mounted. Today the assembling of the magnets is done by hand, which is a very tedious and time-consuming work.  This project presents investigations about the automation of the translator magnetization theoretically and simulation results are preformed in ABB's robot simulation software RobotStudio. Even robot-held tool was designed that enables the robot to be able to magnetize the translator in a simple manner.  The investment cost is roughly 1.5 million SEK. With an economic life-time of five years, the investment costs are estimated to 24000 SEK / month.  According to the calculations, this project is very motivated to implement, as it provides savings up to 17 000 SEK per translator which is 10.2 million SEK assuming that the robot cell is operating at full speed the whole year.According to this thesis work the result is a 4x9 meter cell with two industrial robots of the type ABB IRB6650S.The cycle time to magnetize one translator was calculated to about 10 hours.This prototype of project can possibly be implemented in a full-scale production line and performed according to the calculations and simulations presented in the report. Further work is suggested to improve the tool.Lyssna .

This master?s thesis deals with integrating simulations using Agilents Electronic Design Automation tool ADS with customized Matlab scripts, for solving complex analog and digital radio architectures. In particular, it addresses predistortion, realized in the digital domain, of power amplifiers, modeled in the analog domain. The former is implemented in Matlab while the latter is implemented in ADS. Two versions of integrating the two systems have been tested: 1) Iterative approach on sample basis and 2) Scheduled batch solution by matrix inversion.