Since 1 January 2010 it is a requirement to use the European standards, Eurocodes, in Sweden when constructing bridges. One chapter that has caused an extra amount of problems for the engineers is the one about fatigue analysis, which resulted in us doing this thesis.To do this we had to read all of the Eurocodes that direct, or indirect deals with fatigue and calculating of such. We have read the background documents for the Eurocodes and master?s thesis in the subject. We also studied the calculations of bridges constructed by different construction firms.We have chosen to limit the thesis to discuss only road bridges made of concrete due to the lack of method for verification of concrete in the national appendix.

The comprehensive purpose of this Master of Science thesis is to examine which fleetmanagement services for engineering vehicles, ?Fleetech? preferablyought to develop inorder to reach a broad market and meet the demands of contractors.Scanty explained, fleet management is the management of a company's vehicle fleet and theservices can include a range of functions such as driver management and fuel management. Inshort the thesis encompasses four sections:1.Survey of the general contractor industry: The survey has been preformed toevaluate the potential size of the market for fleet management services in the generalcontractor industry.2.Needs analysis: The needs analysis aim was to define what contractors tasks andgoals are, and to determine what functions they want and need from a system.3.The use of CAN and the technical premises: The prerequisite for developing asophisticated and generic system is that vehicle data can be accessed from the CANbuss.The use of CAN standards in construction equipment has therefore beenexamined.4.Specification: An explicit set of requirements have been set to be satisfied by a fuelmanagement service, based on CAN standard protocol J1939.Important conclusions: The use of CAN protocol standards are extensive and the prerequisitesfor developing elementary and CAN based services good. The services should be compatiblewith different manufacture?smachines.

Outside of many Swedish households today, you will find a typical green wastecontainer. This container has not changed since its introduction, despitecomplaints about foul-smelling and its impractical system. Even if the system usedtoday, still is the most optimal choice, there is a lot of newly developedalternatives out there.Its purpose is to get a broader perspective on how a waste management systemcan be developed into a working, land efficiently and aesthetically pleasing systemof humans and the environment in a small residential area.The authors treat the residential area of Jära, Ekhagen, in Jönköping, which ismanaged by JM AB as a problem area in regards to waste management.The issues raised by the authors are the different waste management systems usedin the corresponding areas of the world, how to apply technical andenvironmental as well as the waste management facilities from financial aspects.In the process, the methods used were literature reviews, case studies and aninterview. The case study was done through a modeling of waste managementsystems in the area Jära and an interview was conducted with the company Envacworking with vacuum systems. Studies have been made by different systems n theareas around the world.The results show that using directives and guidance will reduce the environmentalimpact done without replacing the traditional system.

Today when new and harder demands on CO2 emissions are developed, vehicle manufacturers must work to develop new engine solutions to new kinds of fuels to replace fossil fuels. A fuel that could be applied is hydrogen. When hydrogen is combusted only water vapor occurs. Hydrogen is known to be explosive and flammable. These properties are both good and bad for combustion.

This report relate a concept study that consider a number of different proposals to improve the overcharging system in BAE Systems Ha?gglunds tracked vehicle series BvS10, to maintain sealevel power at extreme altitude.At high altitude the power losses beacuase of the air density that decreases, which results in less fuel can be burned. The decreasing of air density also gives rise to fatigue failure of the turbocharger unless power is reduced.The proposals shall be as required by BAE Systems Ha?gglunds economically sustainable and defensible from a packing perspective. That means the selected solution must have a reasonable price tag and at the same time a minimal impact on adjacent components.The basis for this thesis is based on benchmarking of both the auto industry as the flight industry, to find inspiration and tips for improvement.Some of the concepts have after gathering facts and calculations been excluded while other solutions has been considered as workable and thus interesting for BAE Systems Ha?gglunds.Initially the current turbochargingsystem was analyzed in order to determine the starting point and thus be able to fix the current problems surrounding high altitude driving.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Road transports stand for a great part of Sweden?s total CO2-emissions. Transports are expected to increase over the coming years, and with those the emissions. A greater environmental awareness leads to increased demands for environmentally friendly transport. The aim of this thesis is to study the consequences of changing transportation modes from road to railway.

Water hardness indicates the concentration of calcium and magnesium ions in water. Water with high concentrations of these ions is described as hard water and water with low concentrations is described as soft water. Water that is too hard or too soft can lead to technical and economical problems. In collaboration with Midvatten AB, groundwater hardness in the Badelunda esker between Leksand and Avesta has been mapped, and an attempt has been made to explain the variations. For this purpose, different GIS programs, such as ArcView, ArcInfo, IDIRISI, and one geochemical modelling program, PHREEQC, has been used.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

This report is part of the major thesis carried out at Stoneridge Electronics in Bromma,Stockholm during autumn and winter 2005-2006. The background to the thesis is the trendwithin the automotive industry where color displays have become more common for presentationof information to the driver, a trend that has come to the commercial vehicle market. Thepurpose of the thesis has been to evaluate whether programmable logic, with respect to FPGAtechnology, could be suitable for display control and graphics generation of these more complexcolor displays in automotive environment.Within the scope of the thesis the FPGA technology has been investigated, i.e. whatopportunities and threats there are with aspect to environmental and security requirements. Inaddition, the market of FPGAs and pre-built IP-cores has been investigated.

Nya typer av krigföring, så som COIN-operationer (Counter insurgency), ställer nya krav på flygstridskrafterna. Utvecklingen av det bemannade stridsflyget har, om man jämför med UAV (Unmanned Aerial Vehicle), trots detta stått relativt stilla. Obemannat stridsflyg har samtidigt utvecklat förmågor som gör funktionen till en värdig konkurrent på det moderna slagfältet. Syftet med denna uppsats är att undersöka huruvida obemannat stridsflyg kan överta det bemannade stridsflygets plats inom ramen för COIN-operationer. Detta avser jag uppnå genom att undersöka hur väl de båda funktionerna svarar uppmot de krav som ställs på ett stridsflygplan i en operation med inslag av COIN.

Handling, loading, transport time and unloading in connection to transport of farm animals affect animal welfare. Induced effects include both psychological and physiological stress responses in animals. The physiological parameters may be measured through blood analysis while behavioural changes often manifest themselves through increased vocalisation, escape attempts and apathy. Physiological parameters are additional parameters of importance when measuring animal stress responses. The handlers behavior during transport has been shown to have major impact on animal welfare and the quality of meat. Animal friendly handling and driving of animals create a more manageable work environment for the handlers. To further increase animal welfare in connection to transport, stables should be built with well adapted drift passage and ramps on the transport vehicle.

Title:?Speed cameras - an prevention of crime and a standard forming instrument of control??Authors: Markus HanssonTutors: Bo Isenberg & Carl HultExaminator: Ulf DruggeThe School of Human SciencesUniversity of KalmarThe studys purpose is to get a absorbed understanding for peoples attitude, and effect of speed cameras. The disposition for the study is to integrate earlier studies in the matter, combined with elevating interesting sociological conceptions. As an attempt to understand speed cameras as an instrument of force on the individual have Michel Foucaults concept Panopticon been used to see its effect, and it?s look upon how crime prevention will be formulated, which can give an explanation of why speed cameras are being used as an instrument of control on the traffic area.